http://wiki.makespace.org/api.php?action=feedcontributions&feedformat=atom&user=JCGS 2026-05-29T19:58:35Z User contributions MediaWiki 1.22.6 http://wiki.makespace.org/Equipment/Electronics_Workbenches 2018-06-21T19:53:43Z

<p>JCGS: /* Want */</p> <hr /> <div>{{GreenTool}}<br /> {{OrangeTool}}<br /> <br /> [[Equipment|Equipment]] / Electronics Workbenches<br /> <br /> Workbenches for electronics and precision work.<br /> <br /> [[File:Electronics-thumb.jpg|right]]<br /> <br /> <br /> == Enthusiast Bench ==<br /> A 1800mm x 900mm ESD cantilever bench from [http://www.bigdug.co.uk/workshop-benches-c348/antistatic-workbenches-c721/antistatic-workbenches-capacity-300kgs-pp4582 here]<br /> <br /> === Equipment ===<br /> * Hameg HM-203-5 20MHz analogue oscilloscope<br /> ** [[File:HM203-6_Manual.pdf]]<br /> * Black*Star Jupiter 500 0.1Hz-500kHz function generator (sine, square, sawtooth)<br /> * Philips PM6622 80MHz counter<br /> ** [[File:PM6622_PM6624_PM6625_Manual.pdf]]<br /> <br /> == Expert Bench ==<br /> A 1800mm x 900mm ESD cantilever bench from [http://www.bigdug.co.uk/workshop-benches-c348/antistatic-workbenches-c721/antistatic-workbenches-capacity-300kgs-pp4582 here]<br /> <br /> === Equipment ===<br /> * BlackJack BK6000 Rework station (Class: Orange)<br /> ** [[File:BlackJack_BK6000_Rework_Station_manual.pdf‎]]<br /> * Rigol DS1104Z 100MHZ Digital Oscilloscope<br /> ** Info [http://www.rigolna.com/products/digital-oscilloscopes/ds1000Z/ds1104z/ here].<br /> * Philips PM 3217 50MHz analogue Oscilloscope (Class: Green)<br /> **[[File:Philips_PM3217_50MHz_Oscilloscope_Manual.pdf]]<br /> * Thurlby Thandar TG212 0.1Hz-2MHz function generator (sine, square, sawtooth) (Class: Orange)<br /> ** [[File:TG200_Series_Manual.pdf]]<br /> * Thurlby Thandar TF830 1.3GHz high resolution reciprocal measurement<br /> <br /> == Shared equipment ==<br /> * Soldering irons:<br /> ** 2x Tenma AT60D soldering stations (up to 400C) (Class: Orange)<br /> * Bench power supplies (e.g. a mix of 5V, 12V, variable, and multi-rail PSUs) (Class: Orange)<br /> ** Farnell AP20-80: up to 20V at up to 80A<br /> ** Hameg HM7042-3 dual: each channel up to 32V at up to 2A<br /> ** Tenma 72-8695 two channels each up to 32V at up to 3A, plus a single fixed 5V/2A channel<br /> * Logic analyser:<br /> ** HP 16500A (status unknown: may not be operational but has probes pack)<br /> ** Currently assumed dead.<br /> * Components and small tools<br /> ** PCB holders or &quot;helping hands&quot;<br /> ** Magnifying lamps<br /> ** Side cutters<br /> ** Multimeters<br /> ** Wire<br /> ** Selection of basic components (res, caps, v-reg, basic digital logic, basic IC's - 555,358, connectors, cable)<br /> ** Inspection microscope (fixed 20x monocular, with 80mm clearance under the lens)<br /> * Reflow Oven<br /> ** [[Equipment/Electronics_Workbenches/ReflowOven|Equipment/Electronics_Workbenches/ReflowOven]]<br /> == Supplies ==<br /> <br /> [[Equipment/Electronics_Workbenches/Supplies | Supplies]]<br /> <br /> == Wishlist ==<br /> <br /> ===Need===<br /> * Soldering microscope with inbuilt illumination<br /> * PCB holders ('''not''' just &quot;helping hands&quot;)<br /> * Abrasive pen<br /> * Heatsink tweezers<br /> * Tweezers<br /> * ESD handling equipment, eg. anti-static mats, wrist-strap, earth points, tester<br /> * URLs or PDF manuals for the equipment<br /> <br /> ===Want===<br /> * Logic Analyser<br /> ** Possibly a Saleae [http://www.saleae.com/logic16 Logic16]<br /> * Fridge for solder paste (and glues)<br /> * Solder paste for fridge :)<br /> <br /> ===Would Be Nice===<br /> * USB microscope with monitor (not to be confused with a soldering/lab microscope!)<br /> * Spectrum Analyser<br /> * A PC<br /> <br /> &lt;!--<br /> == Archive==<br /> <br /> &lt;gallery&gt;<br /> File:1836058-40.jpg|[http://cpc.farnell.com/tenma/72-8700/power-supply-bench-2x-32v-5a/dp/IN06096 Dual 32V, 5A Bench Power Supply]<br /> &lt;/gallery&gt;<br /> <br /> Bench Requirements (based on conversations with lots of people!)<br /> * Height: Standard workstation/stool height (~840mm) rather than desk/chair height - allows working standing or sitting on stools<br /> * Depth: Standard electronics workstation depth of ~900mm to allow for equipment at the back whilst still giving decent workspace<br /> * ESD - whilst some people don't care, other seem to care a lot, so assume antistatic worksurface<br /> * Structure - A long workbench surface along the wall of the main workshop, approximately 4m; Options:<br /> ** Standard electronics workbenches (metal structure bench with drawers below left/right, back power strip at back, raised shelf)<br /> ** Basic electronics workbences without storage below, cantilever or 4-post design<br /> ** Worksurface (e.g. kitchen) fixed to wall with some drawer units as stands (e.g. ikea) <br /> * Other considerations:<br /> ** Allow for a variable number of people to sit at it (i.e. bunch up, couple of people around same project)<br /> ** Decent storage for all the basic tools, components<br /> ** Some form of raised area for scopes/test equipment<br /> ** Very sturdy - i.e. wont move if lent on, pushed against etc<br /> --&gt;</div>

JCGS http://wiki.makespace.org/Donations_Policy 2018-06-21T18:52:56Z

<p>JCGS: </p> <hr /> <div>You can't donate equipment to Makespace, but we might buy something from you for a pound.<br /> <br /> (This is so that there is a receipt, so that it's clear that you're not just lending the equipment to us; there has been confusion over this in the past, where we believed that we had been given something, but the person from whom we got it later said they had only lent it to us.)</div>

JCGS http://wiki.makespace.org/Make-a-makespace 2018-06-21T18:34:57Z

<p>JCGS: </p> <hr /> <div>This appears to be our original wishlist. We'll keep it here for posterity.<br /> <br /> = Features of the space =<br /> Mailing list, wiki, IRC<br /> <br /> Office desk space (smaller pods than workbench)<br /> <br /> More post-it notes<br /> <br /> Prototyping boards (mbed, Beagle, Etc) for use AND to buy<br /> <br /> Armour<br /> <br /> Animatronic active/reactive artwork<br /> <br /> Pillar drill<br /> <br /> CAD Software (mech &amp; EDA)<br /> <br /> &lt;nowiki&gt;Papercraft equipment (diecutters, embossers, etc) [So the wife and I can come together]&lt;/nowiki&gt;<br /> <br /> Van<br /> <br /> Wood burning stove<br /> <br /> Project cases to buy (fabbed, or from Maplin)<br /> <br /> Fire/fireworks<br /> <br /> Compost<br /> <br /> Whiteboards or chalkboards<br /> <br /> Chairs<br /> <br /> Web Forum (area 51)<br /> <br /> Multimeter (several!)<br /> <br /> Laser Cutter<br /> <br /> Trips to orbit (!?)<br /> <br /> 24-hour design and build contest<br /> <br /> Toilets!<br /> <br /> Outside space<br /> <br /> Website linked to RFID entry cards<br /> <br /> LEGO<br /> <br /> Component layer<br /> <br /> Oscilloscope<br /> <br /> Software sponsorship/donations<br /> <br /> Phone wall<br /> <br /> Hammocks<br /> <br /> Place to hide stuff from my wife!<br /> <br /> Mail order collection storage<br /> <br /> Microscope<br /> <br /> Compressed air<br /> <br /> Blank CDs<br /> <br /> Industrial safety zone (safe bay)<br /> <br /> Storage trays &amp; parts trays<br /> <br /> Serious lighting<br /> <br /> Box-o-screws<br /> <br /> Single/3phase power<br /> <br /> TV<br /> <br /> Crane (for engines)<br /> <br /> Liquid nitrogen<br /> <br /> Science gear (eg bunsens, crystal growing, test tubes, chem supplies)<br /> <br /> Good GPS/Radio reception<br /> <br /> Patent advice<br /> <br /> Car parking<br /> <br /> hot glue gun<br /> <br /> energy monitoring - live display of site usage<br /> <br /> Freecycle<br /> <br /> Healthy, safe, insured!<br /> <br /> Gas, water, electricity<br /> <br /> Dry ice<br /> <br /> RF shielded box<br /> <br /> Library: stock of relevant books<br /> <br /> Postcard/notice board for user contributions<br /> <br /> Fume cupboard/hood<br /> <br /> CAD station<br /> <br /> IRC<br /> <br /> Rocket launch pad<br /> <br /> Pet enhancements: Robo cat, auto pet doors, <br /> <br /> Unused applications for AlertMe<br /> <br /> 3D camera<br /> <br /> IR camera<br /> <br /> Paint sets<br /> <br /> Sewing for conductive fibres<br /> <br /> LED Collection<br /> <br /> Oxy-acet<br /> <br /> Exercycle electricity generator<br /> <br /> Robot command chair<br /> <br /> Server<br /> <br /> Compos<br /> <br /> Pico projectors<br /> <br /> Cheap, hackable toys<br /> <br /> Bike parking (safe!)<br /> <br /> Datasheet emporium<br /> <br /> Robot arm<br /> <br /> Optical box<br /> <br /> Stonework/bricklaying practice area<br /> <br /> Pick and place<br /> <br /> AR Drones<br /> <br /> Digital download library<br /> <br /> INTERNET CONNECTION!<br /> <br /> Clamps<br /> <br /> Hack Shop (see www.coolcomponents.co.uk)<br /> <br /> Forming jigs<br /> <br /> Raw/retrieved materials bin<br /> <br /> Trailer for materials pick-up<br /> <br /> 3D Scanner<br /> <br /> X-Ray M/C<br /> <br /> Music box<br /> <br /> Frisbee + surveillance camera<br /> <br /> Whiteboard A/V equipment<br /> <br /> Alu Welder<br /> <br /> Walls that post-its actually stick to<br /> <br /> PCB prototyping<br /> <br /> Wii<br /> <br /> Live webcam<br /> <br /> WiFi<br /> <br /> Goggles<br /> <br /> Car lift or pit<br /> <br /> Book-swap library<br /> <br /> Whiteboard that can be printed<br /> <br /> Migratory box of electronics<br /> <br /> Comfy sofas<br /> <br /> Shared (file) storage space<br /> <br /> Good natural light (+2)<br /> <br /> Serious lighting<br /> <br /> Snack bar<br /> <br /> A way to broadcast 'what I'm doing now'<br /> <br /> Cooking equipment (microwave, etc)<br /> <br /> Bike tools<br /> <br /> Borrowable bike trailer<br /> <br /> No rules<br /> <br /> Dark Room<br /> <br /> Fricking LASER<br /> <br /> Digital darkroom<br /> <br /> Parts<br /> <br /> SESolder station<br /> <br /> USB PIC kits<br /> <br /> Solder flow machine<br /> <br /> Oven (fibre glass, etc)<br /> <br /> Sewing machines<br /> <br /> Gloss painted floor<br /> <br /> Stone masonry equipment<br /> <br /> Microsoft SenseCam<br /> <br /> Shower<br /> <br /> Bins for duff stuff<br /> <br /> Jigsaw<br /> <br /> Bench PSU<br /> <br /> JUNK<br /> <br /> Video/music equipment<br /> <br /> BGA Reflow<br /> <br /> A good server<br /> <br /> Basic hand tools<br /> <br /> Infrared camera<br /> <br /> Video camera, tripod, webcam<br /> <br /> Video Conferencing<br /> <br /> RepRap<br /> <br /> MIG/TIG welder<br /> <br /> Food printer<br /> <br /> Rackspace<br /> <br /> Soldering kit<br /> <br /> PU resin casting (vacuum chamber)<br /> <br /> Printer<br /> <br /> Thermal camera<br /> <br /> Woodwork &amp; furniture stuff<br /> <br /> Lego league<br /> <br /> Squash ladder (social life)<br /> <br /> Welding training (+2)<br /> <br /> AI Challenges<br /> <br /> Wood work<br /> <br /> Resident Offices<br /> <br /> Deal w. Dominoes<br /> <br /> Xbox<br /> <br /> Online forum for ideas &amp; discussions<br /> <br /> Fish?<br /> <br /> Musical instruments (Junk Samba?)<br /> <br /> USB I/O Board<br /> <br /> Etch/PCB exposure unit<br /> <br /> Spray booth<br /> <br /> Cheap PCS w. 2 parallel ports<br /> <br /> Notice board<br /> <br /> mbed boards<br /> <br /> Backup server, source control<br /> <br /> Equipment museum<br /> <br /> Account holding (eg Farnell)<br /> <br /> Delivery receiving<br /> <br /> Tea/Coffee<br /> <br /> Big Table<br /> <br /> Films<br /> <br /> Roof Garden<br /> <br /> BBQ<br /> <br /> Tech book loan<br /> <br /> Sell Tshirts<br /> <br /> = Events =<br /> <br /> Robot Wars<br /> <br /> Fix It nights (salvation army)<br /> <br /> Speed dating<br /> <br /> Motor design<br /> <br /> Smallest microcontroller design<br /> <br /> Pyjama party (!?)<br /> <br /> Low energy design<br /> <br /> How to use amazing kit!<br /> <br /> Maker Faire (+1)<br /> <br /> Embedded S/W course<br /> <br /> Cloud platform training<br /> <br /> Linux basics<br /> <br /> (in)famous inventors &amp; their stories<br /> <br /> Stone masonry workshop<br /> <br /> Bridge the Cam<br /> <br /> How to make a film happen<br /> <br /> <br /> = Groups =<br /> <br /> Medical Engineering Group<br /> <br /> Heavy Engineering Group<br /> <br /> City Farm<br /> <br /> Scouts / Guides<br /> <br /> Techhub London<br /> <br /> Theatre Workshops (eg ADC)<br /> <br /> Cam 105 FM<br /> <br /> St Johns Innovation Centre<br /> <br /> Centre for Computer History<br /> <br /> Local venues (Arts, Junction)<br /> <br /> Model Railway Soc.<br /> <br /> Beavers<br /> <br /> Naked Scientists<br /> <br /> Local schools / 6th form / Uni<br /> <br /> Student Unions<br /> <br /> Old-aged support groups<br /> <br /> Cambs Ham Radio<br /> <br /> Camb Geek Nights<br /> <br /> ADC set division<br /> <br /> I.C.E.<br /> <br /> Military engineering groups<br /> <br /> University science + engineering outreach groups<br /> <br /> STEMNet<br /> <br /> Duxford IWM<br /> <br /> Fitzwilliam Museum<br /> <br /> Cambridge Science Festival<br /> <br /> Transition Cambridge</div>

JCGS http://wiki.makespace.org/Family_Makers 2018-06-21T18:08:05Z

<p>JCGS: /* Actions */</p> <hr /> <div>= Aim =<br /> To enable makers and their families and friends to come together, make things and have fun.<br /> <br /> = Description =<br /> In order to progress and get the club set up quickly and reduce the required legal work this will be for existing members, their families and their guests.<br /> The classroom will be the main location used, possibly making use of the kitchen and maybe demonstrating some of the equipment in the workshop.<br /> <br /> = Meetings =<br /> [[Family-Makers-Projects-List]]&lt;br/&gt;<br /> [[Meetings/FamilyMakers12-05-2014]]&lt;br/&gt;<br /> [[Meetings/FamilyMakers05-09-2013]]&lt;br/&gt;<br /> [[Meetings/FamilyMakers04-07-2013]]&lt;br/&gt;<br /> [[Meetings/FamilyMakers04-04-2013]]&lt;br/&gt;<br /> [[Meetings/FamilyMakers17-03-2013]]&lt;br/&gt;<br /> [[Meetings/FamilyMakers17-02-2013]]&lt;br/&gt;<br /> [[Meetings/FamilyMakers03-02-2013]]<br /> <br /> = When =<br /> *Some Sunday mornings: 10-12<br /> *Ideally weekly to enable access for as many as possible, as people will be away and unable to attend every week; however in practice it has been sporadic recently.<br /> [[Family-Makers-Projects-List|Project Schedule 2014]]<br /> &lt;br/&gt;&lt;br/&gt;Previous Projects&lt;br&gt;<br /> [[Family-Makers-Projects-List_2013|Project Schedule 2013]]<br /> <br /> = Who =<br /> * Presenter/Facilitator<br /> * Deputy<br /> ** Turn up a a bit early to set-up registration, put out registration book to record attendees names and photo consent and meeting fees collection box (£3 per family). The registration book and collection box are stored in the Family Makers box in the storage cupboard.<br /> ** Ensure supply of biscuits and squash. These are stored in the Family Makers cupboard (if there are any extra).<br /> <br /> = Rules =<br /> *We should have a committee of at least 3 members to organise and administer the club<br /> *We should have a set of club rules, on top of the Makespace membership rules<br /> *Parents are required to attend, it won't be possible to drop of kids and collect them later<br /> *Full control of children is required as Makespace has potentially dangerous equipment<br /> *Number of kids dependent on behaviour, typically up to 2 as we already have a majority of parents with 2<br /> *Three strikes rule on behaviour, three bad behaviour instances and the child will not be permitted back<br /> *Repeated ‘guests’ need to consider membership<br /> *A committee member should attend each day, be there 15 mins early and organise refreshments and projects plus ensure clear up afterwards.<br /> <br /> = Projects =<br /> <br /> Some future project ideas could be:<br /> *Raspberry Pi<br /> *Basic skills<br /> **Soldering<br /> *Standard kits e.g. Adafruit<br /> *Competitions<br /> **Cars<br /> **Robots<br /> *Laser cutter demo<br /> *3D print demo<br /> *Educational component – e.g. what is this resistor doing?<br /> *Sewing/knitting/weaving (by hand and using sewing machines) [beck can facilitate hand sewing/weaving and could help with machine sewing]<br /> *PaperCraft/Origami<br /> **I have a set of PaperCraft designs of locks, combination, cylinder etc, which are interesting to build and result in a working (but fragile) lock, RodW<br /> *Use 123D catch to capture 3D models, possibly heads <br /> *Use 123D Creatures to design 3D monsters and cartoons, then 3d print them.<br /> *Make a timing system for toy cars. BC<br /> *pin hole cameras. BC<br /> *spy stuff - make badges, long distance mic, spy cameras, spy gadgets. BC<br /> *Mask-making<br /> *Kites<br /> *Stamping, printings on paper or fabric<br /> *Jewellery/bead-making (paper, metal, clay, salt dough, etc.)<br /> *Bread animals [beck]<br /> *Baking (cupcakes, muffins, biscuits) [beck]<br /> *Picture taking morning (e.g., [http://www.instantshift.com/2010/08/24/88-brilliant-examples-of-forced-perspective-photography/ Forced perspective photography])<br /> *One Pot Electronics Engineering - many projects to choose from [http://ee.onepotcooking.com/syllabus One Pot Electronics Engineering]<br /> <br /> <br /> <br /> Longer Projects<br /> *Create a mold and cast something - low tech by cutting out layers of ply, vacuum mold a heated plastic sheet and cast chocolate. <br /> *Conductive Fabric - Sewing, sensors and simple circuits.<br /> *3D generative programs, create program (in openscad) that will generate 3D models, add parameterisation via thingiverse customizer script, 3D print<br /> *Create a polagraph, draw quirky pictures slowly<br /> *Raid Make magazine, [http://blog.makezine.com/projects/make-33/vinyl-pcb-resist/ Vinyl PCB Resist]encourages custom/artistic circuit diagrams and the process teachs circuit board basics<br /> *build a maze solving robot and enter it in to Competitions. BC<br /> *build 3D printer - maybe a reprap. BC<br /> *[[Family makers electronics sessions]]<br /> <br /> = Legal =<br /> &lt;Todo&gt;<br /> <br /> = Funding =<br /> *Initial investment <br /> **Makespace ?<br /> **Founding members?<br /> *Weekly fees<br /> **£3.00 for each member family and £5.00 for a non member family to cover refreshments and consumables<br /> &lt;br/&gt;<br /> <br /> = Other =<br /> *Communication – who, when, how?<br /> *Wiki page, web page, twitter, calendar, meetup pages<br /> *Founding families<br /> *Outreach targets ?<br /> *Sources for kits and spares<br /> *Refreshments: Squash, snacks<br /> *Are two members needed for each club event so that one can escort non members through the space if required?<br /> *Future coordination with other groups?<br /> *Committee meetings – how frequently? Monthly initially<br /> *How many people interested?<br /> *Who will actively attend?<br /> *Next meeting end of Feb<br /> <br /> = Links =<br /> Some links that could have useful information for us going forward:<br /> * [http://hackerscouts.acemonstertoys.org/ Hacker Scouts]<br /> *Instructables<br /> *Lego<br /> *Engineering faculty days – [mailto:outreach-officer@eng.cam.ac.uk Maria Kettle] <br /> *Adafruit<br /> *Proto pic<br /> * [http://www.theroboticist.org/ The Roboticist] (Seattle-based robot club for young kids)<br /> * [https://docs.google.com/file/d/0B9esWAj9mpBLNmRlMWYxZjUtZjJjMi00NTdhLThmNjUtMmM5ZDk5NTZmMzBh/preview Maker Club Play book] link to a document about setting up a maker club for older children.<br /> * [http://youngmakers.org/ Young Makers website] the site where I found the above play book.<br /> * [http://www.mindsetsonline.co.uk/ Mindsets Online]<br /> * AccessArt http://www.accessart.org.uk/<br /> * Things To Make And Do http://www.things-to-make-and-do.co.uk/index.html<br /> <br /> = Notes from Discussion with Maria Kettle =<br /> <br /> <br /> These are notes from my (MW) email discussion with Maria Kettle, Outreach Officer for Cambridge University Engineering Department. CUED hosts events for kids and their parents/guardians every other month, with projects and concerns very similar to Makespace's Family Makers.<br /> <br /> <br /> '''What projects have worked well and what haven't?'''<br /> <br /> * Electrical things usually go OK and can be split into a minimum needed for success (build a hovercraft) plus an extension (put a skirt on your hovercraft, decorate a jitterbug). They are expensive in terms of components, batteries etc. <br /> * Rolled paper tube structures are cheap but hard to complete in 1 1/2 hours for a small team. Also, people seem to think that cranes, bridges, towers and boats are all the same - rolled paper tubes. <br /> * Strangely, the electrical things, hovercraft, jitterbugs, crazy kit cars are not the same, even though they are all based on a battery box wired to a motor...<br /> * My only disaster was making gliders, the 2nd event I did. The gliders were fine and people had fun but some kids had the bright idea of launching their gliders from the mezzanine floor of engineering reception. The uprights that support the handrail around this floor are 1950's spec - very widely spaced. A kid could launch itself through them very easily, a H&amp;S nightmare. I now put &quot;No Entry&quot; signs at the bottom of the main building stairs.<br /> <br /> <br /> '''Might it be possible to reuse any of your projects?'''<br /> <br /> * Hunt about here and see if you can find anything useful:<br /> [http://www.eng.cam.ac.uk/outreach/Project-resources/Links-to-resources1.html CUED Outreach Resources] and here: [http://www.stemclubs.net/activity Stem Clubs Activities]<br /> <br /> <br /> '''How do you source funding?'''<br /> <br /> * Outreach at Engineering is funded by some big wedges of cash from industrialists who have a vested interest in increasing the numbers going into the profession at all levels. The University brand helps massively here. At family events, I put out a bucket and ask for suggested donations of £5. The actual amount I get is very variable but overall it covers the cost of sandwich lunches for the volunteers. <br /> <br /> <br /> '''Were there any legal challenges to setting up the programme?'''<br /> <br /> * We don't have event insurance. Instead, all the volunteers are STEM Ambassadors. This gives them personal liability insurance if they are at an event that is notified to our local STEMNET organization, STEM TEAM East, in advance. You can find out more about becoming a STEM Ambassador here: [http://www.eng.cam.ac.uk/outreach/CUED-students-and-staff/STEM-Ambassador-Application/Links-to-instructions.html STEM Ambassador Application]. The activities we do are not very dangerous.<br /> * We ask for signed photo consent from the responsible adults. I tell people that I use the photos to decorate my website, to decorate reports to sponsors and to decorate applications for cash. The wording of the form is much more wide open than this and I once had a solicitor parent refuse to sign it on grounds of its wideness. I have now decided that if this ever happens again, I will ask the lawyer-parent to help me draft something more realistic but I missed that opportunity. However, if someone refuses photo consent, don't ask why and don't take any photos. <br /> * The rules around maintaining the anonymity of adopted kids are VERY tight for good but horrid reasons. A photo of an adoptee at your event would tie the kid to a geographical location and could have very nasty consequences, kids are not lightly put up for adoption. Birth parents may not have seen the child for many years but they are usually sent carefully de-localised photos and news a couple of time per year so they could recognise a child on your website. Don't go there.<br /> * Also, in future, I'll tell people about photo consent in the information email I send out to confirm a booking. I had a mum reluctant to sign consent for her son's mate without asking mate's mum first.<br /> <br /> <br /> '''What did you do about formulating a set of rules?'''<br /> <br /> Trial and error! The rules we use are minimal and relate to<br /> * 1) All groups must have a responsible adult. <br /> * 2) Event volunteers only interact with kids professionally, that is, we are all in a room with lots of other people. We don't take kids to the loos, that is the job of a responsible adult if necessary. Stickers are handed to kids for them to stick onto themselves. This seems very paranoid as I write it but it is standard school practice. There is a CUED policy on working with children and vulnerable adults that covers this stuff in detail, I've attached a copy [[https://docs.google.com/document/d/1eimyJha_YYYBaMdDhtRRvO_T6T3pQLk3sQQrBUxESmc/edit?usp=sharing link to document]].<br /> * 3) Rules to stop kid A accidentally trashing kid B's hovercraft/boat or kid C's rubber band powered helicopter getting mashed into kid D's hair. We have testing areas, and all testing must be done there.<br /> <br /> <br /> '''What adult/child/teacher ratios to you recommend?'''<br /> <br /> * At least 1 responsible adult per group and don't have more kids in that group than the adult can cope with. This is flexible to allow for bigger groups of more experienced participants and smaller groups of younger kids. I recruit as many volunteers as possible, having too many is never an issue, sadly. The extra help they provide becomes an icing on the cake for family groups. I have a balloon powered bus activity that is mostly colouring to offer to very young children who arrive on the coat tails of older siblings.<br /> <br /> <br /> '''Are you aware of external sources of funding for children/technology programmes?'''<br /> <br /> * No.<br /> <br /> = Notes from the Maker Club Playbook =<br /> <br /> These are notes that I (MW) have taken on the [https://docs.google.com/file/d/0B9esWAj9mpBLNmRlMWYxZjUtZjJjMi00NTdhLThmNjUtMmM5ZDk5NTZmMzBh/preview Maker Club Playbook] (see the Links section above). The Playbook is a guide for setting up maker groups with older kids (ages 12-18) to get projects ready for Maker Faires. Even though we will not be preparing projects for Maker Faires (not yet, at least!), and there will be younger kids in our group, there is a lot from the Playbook that is helpful and relevant. Below I pull out what I think is most useful (but another person to scour the Playbook and find other important points would be good). In particular, I want to pay attention to the sections on philosophy and documentation: Ensuring our group has the right attitudes and making sure that we document our ideas and accomplishments is crucial. All is up for discussion, of course!<br /> <br /> <br /> '''Philosophy/Approach''' (p. 5): <br /> * &quot;Makers believe that if you can imagine it, you can make it. We see ourselves as more than consumers--we are productive; we are creative. Everyone is a Maker, and our world is what we make it.&quot;<br /> * &quot;Makers comprise a community of crative and technical people that help one another do better. They are open, inclusive, encouraging and generous in spirit.&quot;<br /> * &quot;Makers celebrate other Makers -- what they make, how they make it and the enthusiasm and passion that drives them.&quot;<br /> * &quot;Maker Clubs are about exhibition, not competition. We don't see Makers pitting themselves against each other. We hope each Maker gets useful feedback on what they exhibit, and that the feedback is offered in a spirit of generosity and received with similar openess and magnanimity.&quot;<br /> * And from p. 7: &quot;...[T]here are no winners or losers -- anything that's cool is fair game. It's not a competition and there aren't prizes, so there are no judges deciding who has succeeded and who has failed. ... [M]ost importantly, we notice that all Makers are curious and motivated people.&quot;<br /> <br /> <br /> '''Starter Projects''' (pp. 8-9)<br /> * &quot;We recommend that you make something [simple] together to get your feet we and see what it's like to work together&quot;<br /> * The Playbook recommends many websites for finding starter projects including Make:Projects, simpler Instructables projects and Build Howtoons projects. [We should see also the links that Maria Kettle from CUED has suggested.]<br /> * &quot;When choosing a starter project, consider the diverse interests and skill sets of the members of your club, and make sure that the project you choose is open-ended enough to welcome all kinds of budding Makers into the culture.&quot;<br /> <br /> <br /> '''Plussing''' (p. 11)<br /> * &quot;Pixar uses the term 'plussing' to men finding what's good about an idea and making it even better. In the Young Makers program, plussing sessions provide an opportunity for project teams to share their ideas, progress, challenges and next steps with the participants...&quot;<br /> * &quot;Through the Young Makers program we are modeling and sustaining a collaborative culture, and having highly interactive plussing plays a key role in reaching that goal. Admittedly the adult mentors and volunteers tend to have the most to say during the plussing sessions. It takes a lot of work to get kids to comment on one another's projects, but it is critical you put the effort into encouraging the kids to plus too.&quot;<br /> <br /> <br /> '''Documenting''' (pp. 12-13)<br /> <br /> I (MW) am keen that we start documenting the Family Maker mornings early on and have a plan for how we'd like to present what we do there. It will be important for record keeping and later on for outreach. Minimally we need (I think) project notebooks for each kid or family group and someone designated to take pictures at each session.<br /> * &quot;It's not enough to just make something--it's also important to be able to tell others about the projects and why they are great. To tell their stories better, your club's project teams will want to think ahead to make sure they have the tools they need to document their processes and their final project.&quot;<br /> * &quot;Documentation could take many forms, but whatever medium the members choose to tell their story, the important thing is that it captures why and how they made what they made.&quot; This could include:<br /> * &quot;Notebooks, blogs, project binders, photos, posters, how-to's (to contribute back to the larger Maker community), slideshows, videos, digital stories, project books.<br /> <br /> <br /> '''Designing creative environments''' (p. 16)<br /> * &quot;Make a variety of materials available, but also visible and easy-to-find. You might use clear or mesh containers that members can scan visually when they're looking for something specific or letting their imagination wander as they have Maker's Block. Keep something like an 'idea rummage box' in the space, where members can throw in cool clippings and clever projects they think could inspire others. Choose well-placed shelves and wall space for showcasing examples of past projects and current activities to seed ideas and inspiration.&quot;<br /> <br /> <br /> '''Safety and Training''' (pp. 18-19)<br /> <br /> There is a lot of useful information in this section (that cannot be summed up in a few quotes) such as &quot;avoid using a table saw when you can,&quot; &quot;aim away from yourself,&quot; &quot;secure your work when using hand or power tools&quot; and &quot;don't touch a bare wire, or cut any wire, until you're sure where the other end goes.&quot; It's worth going through all of the points in the Playbook to make sure we've considered everything.<br /> * A good rhyme: &quot;Protect. Double-check. Aim away. Clamp it. Focus. Never play.&quot;<br /> <br /> <br /> '''Mentors''' (pp. 20-21)<br /> <br /> As the kids start to develop ideas and projects of their own, we might want to find mentors to help (especially if the parents are not knowledgeable enough to help). The mentoring section of the Playbook is very good and worth a close read. <br /> * &quot;Mentors are adults who are interested in working with youth and who may be experienced in one or more forms of making. Mentors answer technical questions, address supply issues, pass on their knowledge of tool usage and safety, and help mange realistic project-build schedules. Along the way, mentors might exploit 'teachable moments' to explain underlying math, science and engineering concepts.&quot;<br /> * &quot;We have gleaned a number of tips from effective mentors who have participated in the Young Makers program [each one of these is fully fleshed out in the Playbook]: Help define scope; Help define schedules; Nurture note taking; Embrace failure and keep it safe; Avoid empty praise; Use your down-time well.&quot;<br /> <br /> <br /> '''Setup a website and/or a blog''' (p. 27)<br /> * &quot;''We strongly urge all clubs to create a website''. We also encourage every project team within a club to maintain a blog to track their project's progress. A website is a great tool to use to connect to your club members, as well as connecting to other blggs, and the greater community of Young Maker supporters... You can use it to document project made by your club, to recruit new members, and to maintain a schedule of build sessions.&quot;<br /> <br /> <br /> '''Come up with an identity''' (p. 27)<br /> * &quot;One advantage of a club is the opportunity to create a shared identity. Such things as adopting a mascot, designing a logo, having T-shirts made, having a website and picking a fun name can all help to create a sense of shared purpose and belonging. You'll probably want to pick an identity with member input, but don't spend too much valuable meeting time word-smithing your group's name. Then, in true Young Maker spirit, ask one of your Young Makers to create the logo and perhaps even manage the website. Some project teams may want to create a T-shirt to wear when they exhibit or present their work.&quot;<br /> <br /> <br /> '''Kick it off''' (pp. 29-30)<br /> * &quot;...[A]t the first meeting of the season, we have started with some low-key initiations: very brief introductions, then a little bit of making, and we end the gathering by giving all the new Young Makers brand new Maker's Notebooks where they can start jotting notes, making sketches and diagrams and recording things they find inspiring. We also ask that members sign an agreement that spells out the things they should expect of their experience and the commitments they've made. See the Resources section for a sample Participant Agreement.&quot;<br /> * &quot;You might also start your session with some ways to break the ice and also dig up helpful data.&quot;<br /> * &quot;Some goals for the kickoff meeting: 1) Introduce everyone; 2) Distribute notebooks or ask members to start them; 3) Get a sense of who is in the group, their skill level, and whether they have a project picked out; 4) Ask all participants to sign participation agreements.&quot;<br /> <br /> = Actions =<br /> {| class=&quot;wikitable&quot;<br /> !Action<br /> !Owner<br /> !Expected Date<br /> !Comments<br /> |-<br /> |Create a Meetup for the next meeting<br /> |<br /> |<br /> |<br /> |-<br /> |Start separate discussions on the Google group for the areas that need to be clarified<br /> |Steve U<br /> |<br /> |<br /> |-<br /> |Talk to Laura about the legal elements<br /> |Steve U<br /> |<br /> |<br /> |-<br /> |Contact details for [mailto:outreach-officer@eng.cam.ac.uk Outreach Officer] at Engineering Faculty<br /> |Meg W<br /> |<br /> |(MW) done - notes above<br /> |-<br /> |Contact friend at the [http://www.theroboticist.org/ Seattle kids' robotics club] for tips on setting up a club<br /> |Meg W<br /> |<br /> |(MW) done - waiting for reply<br /> |-<br /> |Define the steps to set the club up<br /> |<br /> |<br /> |<br /> |-<br /> |Define what we need to get access to the Makespace classroom<br /> |<br /> |<br /> |<br /> |-<br /> |Membership for Chris, Meg and Rod<br /> |Chris V, Meg W, Rod W<br /> |<br /> |<br /> |-<br /> |Risk assessments – what needs to be done?<br /> |<br /> |<br /> |<br /> |-<br /> |Do we need at least one founder in attendance?<br /> |<br /> |<br /> |<br /> |}</div>

JCGS http://wiki.makespace.org/Family_Makers 2018-06-21T18:06:53Z

<p>JCGS: /* When */</p> <hr /> <div>= Aim =<br /> To enable makers and their families and friends to come together, make things and have fun.<br /> <br /> = Description =<br /> In order to progress and get the club set up quickly and reduce the required legal work this will be for existing members, their families and their guests.<br /> The classroom will be the main location used, possibly making use of the kitchen and maybe demonstrating some of the equipment in the workshop.<br /> <br /> = Meetings =<br /> [[Family-Makers-Projects-List]]&lt;br/&gt;<br /> [[Meetings/FamilyMakers12-05-2014]]&lt;br/&gt;<br /> [[Meetings/FamilyMakers05-09-2013]]&lt;br/&gt;<br /> [[Meetings/FamilyMakers04-07-2013]]&lt;br/&gt;<br /> [[Meetings/FamilyMakers04-04-2013]]&lt;br/&gt;<br /> [[Meetings/FamilyMakers17-03-2013]]&lt;br/&gt;<br /> [[Meetings/FamilyMakers17-02-2013]]&lt;br/&gt;<br /> [[Meetings/FamilyMakers03-02-2013]]<br /> <br /> = When =<br /> *Some Sunday mornings: 10-12<br /> *Ideally weekly to enable access for as many as possible, as people will be away and unable to attend every week; however in practice it has been sporadic recently.<br /> [[Family-Makers-Projects-List|Project Schedule 2014]]<br /> &lt;br/&gt;&lt;br/&gt;Previous Projects&lt;br&gt;<br /> [[Family-Makers-Projects-List_2013|Project Schedule 2013]]<br /> <br /> = Who =<br /> * Presenter/Facilitator<br /> * Deputy<br /> ** Turn up a a bit early to set-up registration, put out registration book to record attendees names and photo consent and meeting fees collection box (£3 per family). The registration book and collection box are stored in the Family Makers box in the storage cupboard.<br /> ** Ensure supply of biscuits and squash. These are stored in the Family Makers cupboard (if there are any extra).<br /> <br /> = Rules =<br /> *We should have a committee of at least 3 members to organise and administer the club<br /> *We should have a set of club rules, on top of the Makespace membership rules<br /> *Parents are required to attend, it won't be possible to drop of kids and collect them later<br /> *Full control of children is required as Makespace has potentially dangerous equipment<br /> *Number of kids dependent on behaviour, typically up to 2 as we already have a majority of parents with 2<br /> *Three strikes rule on behaviour, three bad behaviour instances and the child will not be permitted back<br /> *Repeated ‘guests’ need to consider membership<br /> *A committee member should attend each day, be there 15 mins early and organise refreshments and projects plus ensure clear up afterwards.<br /> <br /> = Projects =<br /> <br /> Some future project ideas could be:<br /> *Raspberry Pi<br /> *Basic skills<br /> **Soldering<br /> *Standard kits e.g. Adafruit<br /> *Competitions<br /> **Cars<br /> **Robots<br /> *Laser cutter demo<br /> *3D print demo<br /> *Educational component – e.g. what is this resistor doing?<br /> *Sewing/knitting/weaving (by hand and using sewing machines) [beck can facilitate hand sewing/weaving and could help with machine sewing]<br /> *PaperCraft/Origami<br /> **I have a set of PaperCraft designs of locks, combination, cylinder etc, which are interesting to build and result in a working (but fragile) lock, RodW<br /> *Use 123D catch to capture 3D models, possibly heads <br /> *Use 123D Creatures to design 3D monsters and cartoons, then 3d print them.<br /> *Make a timing system for toy cars. BC<br /> *pin hole cameras. BC<br /> *spy stuff - make badges, long distance mic, spy cameras, spy gadgets. BC<br /> *Mask-making<br /> *Kites<br /> *Stamping, printings on paper or fabric<br /> *Jewellery/bead-making (paper, metal, clay, salt dough, etc.)<br /> *Bread animals [beck]<br /> *Baking (cupcakes, muffins, biscuits) [beck]<br /> *Picture taking morning (e.g., [http://www.instantshift.com/2010/08/24/88-brilliant-examples-of-forced-perspective-photography/ Forced perspective photography])<br /> *One Pot Electronics Engineering - many projects to choose from [http://ee.onepotcooking.com/syllabus One Pot Electronics Engineering]<br /> <br /> <br /> <br /> Longer Projects<br /> *Create a mold and cast something - low tech by cutting out layers of ply, vacuum mold a heated plastic sheet and cast chocolate. <br /> *Conductive Fabric - Sewing, sensors and simple circuits.<br /> *3D generative programs, create program (in openscad) that will generate 3D models, add parameterisation via thingiverse customizer script, 3D print<br /> *Create a polagraph, draw quirky pictures slowly<br /> *Raid Make magazine, [http://blog.makezine.com/projects/make-33/vinyl-pcb-resist/ Vinyl PCB Resist]encourages custom/artistic circuit diagrams and the process teachs circuit board basics<br /> *build a maze solving robot and enter it in to Competitions. BC<br /> *build 3D printer - maybe a reprap. BC<br /> *[[Family makers electronics sessions]]<br /> <br /> = Legal =<br /> &lt;Todo&gt;<br /> <br /> = Funding =<br /> *Initial investment <br /> **Makespace ?<br /> **Founding members?<br /> *Weekly fees<br /> **£3.00 for each member family and £5.00 for a non member family to cover refreshments and consumables<br /> &lt;br/&gt;<br /> <br /> = Other =<br /> *Communication – who, when, how?<br /> *Wiki page, web page, twitter, calendar, meetup pages<br /> *Founding families<br /> *Outreach targets ?<br /> *Sources for kits and spares<br /> *Refreshments: Squash, snacks<br /> *Are two members needed for each club event so that one can escort non members through the space if required?<br /> *Future coordination with other groups?<br /> *Committee meetings – how frequently? Monthly initially<br /> *How many people interested?<br /> *Who will actively attend?<br /> *Next meeting end of Feb<br /> <br /> = Links =<br /> Some links that could have useful information for us going forward:<br /> * [http://hackerscouts.acemonstertoys.org/ Hacker Scouts]<br /> *Instructables<br /> *Lego<br /> *Engineering faculty days – [mailto:outreach-officer@eng.cam.ac.uk Maria Kettle] <br /> *Adafruit<br /> *Proto pic<br /> * [http://www.theroboticist.org/ The Roboticist] (Seattle-based robot club for young kids)<br /> * [https://docs.google.com/file/d/0B9esWAj9mpBLNmRlMWYxZjUtZjJjMi00NTdhLThmNjUtMmM5ZDk5NTZmMzBh/preview Maker Club Play book] link to a document about setting up a maker club for older children.<br /> * [http://youngmakers.org/ Young Makers website] the site where I found the above play book.<br /> * [http://www.mindsetsonline.co.uk/ Mindsets Online]<br /> * AccessArt http://www.accessart.org.uk/<br /> * Things To Make And Do http://www.things-to-make-and-do.co.uk/index.html<br /> <br /> = Notes from Discussion with Maria Kettle =<br /> <br /> <br /> These are notes from my (MW) email discussion with Maria Kettle, Outreach Officer for Cambridge University Engineering Department. CUED hosts events for kids and their parents/guardians every other month, with projects and concerns very similar to Makespace's Family Makers.<br /> <br /> <br /> '''What projects have worked well and what haven't?'''<br /> <br /> * Electrical things usually go OK and can be split into a minimum needed for success (build a hovercraft) plus an extension (put a skirt on your hovercraft, decorate a jitterbug). They are expensive in terms of components, batteries etc. <br /> * Rolled paper tube structures are cheap but hard to complete in 1 1/2 hours for a small team. Also, people seem to think that cranes, bridges, towers and boats are all the same - rolled paper tubes. <br /> * Strangely, the electrical things, hovercraft, jitterbugs, crazy kit cars are not the same, even though they are all based on a battery box wired to a motor...<br /> * My only disaster was making gliders, the 2nd event I did. The gliders were fine and people had fun but some kids had the bright idea of launching their gliders from the mezzanine floor of engineering reception. The uprights that support the handrail around this floor are 1950's spec - very widely spaced. A kid could launch itself through them very easily, a H&amp;S nightmare. I now put &quot;No Entry&quot; signs at the bottom of the main building stairs.<br /> <br /> <br /> '''Might it be possible to reuse any of your projects?'''<br /> <br /> * Hunt about here and see if you can find anything useful:<br /> [http://www.eng.cam.ac.uk/outreach/Project-resources/Links-to-resources1.html CUED Outreach Resources] and here: [http://www.stemclubs.net/activity Stem Clubs Activities]<br /> <br /> <br /> '''How do you source funding?'''<br /> <br /> * Outreach at Engineering is funded by some big wedges of cash from industrialists who have a vested interest in increasing the numbers going into the profession at all levels. The University brand helps massively here. At family events, I put out a bucket and ask for suggested donations of £5. The actual amount I get is very variable but overall it covers the cost of sandwich lunches for the volunteers. <br /> <br /> <br /> '''Were there any legal challenges to setting up the programme?'''<br /> <br /> * We don't have event insurance. Instead, all the volunteers are STEM Ambassadors. This gives them personal liability insurance if they are at an event that is notified to our local STEMNET organization, STEM TEAM East, in advance. You can find out more about becoming a STEM Ambassador here: [http://www.eng.cam.ac.uk/outreach/CUED-students-and-staff/STEM-Ambassador-Application/Links-to-instructions.html STEM Ambassador Application]. The activities we do are not very dangerous.<br /> * We ask for signed photo consent from the responsible adults. I tell people that I use the photos to decorate my website, to decorate reports to sponsors and to decorate applications for cash. The wording of the form is much more wide open than this and I once had a solicitor parent refuse to sign it on grounds of its wideness. I have now decided that if this ever happens again, I will ask the lawyer-parent to help me draft something more realistic but I missed that opportunity. However, if someone refuses photo consent, don't ask why and don't take any photos. <br /> * The rules around maintaining the anonymity of adopted kids are VERY tight for good but horrid reasons. A photo of an adoptee at your event would tie the kid to a geographical location and could have very nasty consequences, kids are not lightly put up for adoption. Birth parents may not have seen the child for many years but they are usually sent carefully de-localised photos and news a couple of time per year so they could recognise a child on your website. Don't go there.<br /> * Also, in future, I'll tell people about photo consent in the information email I send out to confirm a booking. I had a mum reluctant to sign consent for her son's mate without asking mate's mum first.<br /> <br /> <br /> '''What did you do about formulating a set of rules?'''<br /> <br /> Trial and error! The rules we use are minimal and relate to<br /> * 1) All groups must have a responsible adult. <br /> * 2) Event volunteers only interact with kids professionally, that is, we are all in a room with lots of other people. We don't take kids to the loos, that is the job of a responsible adult if necessary. Stickers are handed to kids for them to stick onto themselves. This seems very paranoid as I write it but it is standard school practice. There is a CUED policy on working with children and vulnerable adults that covers this stuff in detail, I've attached a copy [[https://docs.google.com/document/d/1eimyJha_YYYBaMdDhtRRvO_T6T3pQLk3sQQrBUxESmc/edit?usp=sharing link to document]].<br /> * 3) Rules to stop kid A accidentally trashing kid B's hovercraft/boat or kid C's rubber band powered helicopter getting mashed into kid D's hair. We have testing areas, and all testing must be done there.<br /> <br /> <br /> '''What adult/child/teacher ratios to you recommend?'''<br /> <br /> * At least 1 responsible adult per group and don't have more kids in that group than the adult can cope with. This is flexible to allow for bigger groups of more experienced participants and smaller groups of younger kids. I recruit as many volunteers as possible, having too many is never an issue, sadly. The extra help they provide becomes an icing on the cake for family groups. I have a balloon powered bus activity that is mostly colouring to offer to very young children who arrive on the coat tails of older siblings.<br /> <br /> <br /> '''Are you aware of external sources of funding for children/technology programmes?'''<br /> <br /> * No.<br /> <br /> = Notes from the Maker Club Playbook =<br /> <br /> These are notes that I (MW) have taken on the [https://docs.google.com/file/d/0B9esWAj9mpBLNmRlMWYxZjUtZjJjMi00NTdhLThmNjUtMmM5ZDk5NTZmMzBh/preview Maker Club Playbook] (see the Links section above). The Playbook is a guide for setting up maker groups with older kids (ages 12-18) to get projects ready for Maker Faires. Even though we will not be preparing projects for Maker Faires (not yet, at least!), and there will be younger kids in our group, there is a lot from the Playbook that is helpful and relevant. Below I pull out what I think is most useful (but another person to scour the Playbook and find other important points would be good). In particular, I want to pay attention to the sections on philosophy and documentation: Ensuring our group has the right attitudes and making sure that we document our ideas and accomplishments is crucial. All is up for discussion, of course!<br /> <br /> <br /> '''Philosophy/Approach''' (p. 5): <br /> * &quot;Makers believe that if you can imagine it, you can make it. We see ourselves as more than consumers--we are productive; we are creative. Everyone is a Maker, and our world is what we make it.&quot;<br /> * &quot;Makers comprise a community of crative and technical people that help one another do better. They are open, inclusive, encouraging and generous in spirit.&quot;<br /> * &quot;Makers celebrate other Makers -- what they make, how they make it and the enthusiasm and passion that drives them.&quot;<br /> * &quot;Maker Clubs are about exhibition, not competition. We don't see Makers pitting themselves against each other. We hope each Maker gets useful feedback on what they exhibit, and that the feedback is offered in a spirit of generosity and received with similar openess and magnanimity.&quot;<br /> * And from p. 7: &quot;...[T]here are no winners or losers -- anything that's cool is fair game. It's not a competition and there aren't prizes, so there are no judges deciding who has succeeded and who has failed. ... [M]ost importantly, we notice that all Makers are curious and motivated people.&quot;<br /> <br /> <br /> '''Starter Projects''' (pp. 8-9)<br /> * &quot;We recommend that you make something [simple] together to get your feet we and see what it's like to work together&quot;<br /> * The Playbook recommends many websites for finding starter projects including Make:Projects, simpler Instructables projects and Build Howtoons projects. [We should see also the links that Maria Kettle from CUED has suggested.]<br /> * &quot;When choosing a starter project, consider the diverse interests and skill sets of the members of your club, and make sure that the project you choose is open-ended enough to welcome all kinds of budding Makers into the culture.&quot;<br /> <br /> <br /> '''Plussing''' (p. 11)<br /> * &quot;Pixar uses the term 'plussing' to men finding what's good about an idea and making it even better. In the Young Makers program, plussing sessions provide an opportunity for project teams to share their ideas, progress, challenges and next steps with the participants...&quot;<br /> * &quot;Through the Young Makers program we are modeling and sustaining a collaborative culture, and having highly interactive plussing plays a key role in reaching that goal. Admittedly the adult mentors and volunteers tend to have the most to say during the plussing sessions. It takes a lot of work to get kids to comment on one another's projects, but it is critical you put the effort into encouraging the kids to plus too.&quot;<br /> <br /> <br /> '''Documenting''' (pp. 12-13)<br /> <br /> I (MW) am keen that we start documenting the Family Maker mornings early on and have a plan for how we'd like to present what we do there. It will be important for record keeping and later on for outreach. Minimally we need (I think) project notebooks for each kid or family group and someone designated to take pictures at each session.<br /> * &quot;It's not enough to just make something--it's also important to be able to tell others about the projects and why they are great. To tell their stories better, your club's project teams will want to think ahead to make sure they have the tools they need to document their processes and their final project.&quot;<br /> * &quot;Documentation could take many forms, but whatever medium the members choose to tell their story, the important thing is that it captures why and how they made what they made.&quot; This could include:<br /> * &quot;Notebooks, blogs, project binders, photos, posters, how-to's (to contribute back to the larger Maker community), slideshows, videos, digital stories, project books.<br /> <br /> <br /> '''Designing creative environments''' (p. 16)<br /> * &quot;Make a variety of materials available, but also visible and easy-to-find. You might use clear or mesh containers that members can scan visually when they're looking for something specific or letting their imagination wander as they have Maker's Block. Keep something like an 'idea rummage box' in the space, where members can throw in cool clippings and clever projects they think could inspire others. Choose well-placed shelves and wall space for showcasing examples of past projects and current activities to seed ideas and inspiration.&quot;<br /> <br /> <br /> '''Safety and Training''' (pp. 18-19)<br /> <br /> There is a lot of useful information in this section (that cannot be summed up in a few quotes) such as &quot;avoid using a table saw when you can,&quot; &quot;aim away from yourself,&quot; &quot;secure your work when using hand or power tools&quot; and &quot;don't touch a bare wire, or cut any wire, until you're sure where the other end goes.&quot; It's worth going through all of the points in the Playbook to make sure we've considered everything.<br /> * A good rhyme: &quot;Protect. Double-check. Aim away. Clamp it. Focus. Never play.&quot;<br /> <br /> <br /> '''Mentors''' (pp. 20-21)<br /> <br /> As the kids start to develop ideas and projects of their own, we might want to find mentors to help (especially if the parents are not knowledgeable enough to help). The mentoring section of the Playbook is very good and worth a close read. <br /> * &quot;Mentors are adults who are interested in working with youth and who may be experienced in one or more forms of making. Mentors answer technical questions, address supply issues, pass on their knowledge of tool usage and safety, and help mange realistic project-build schedules. Along the way, mentors might exploit 'teachable moments' to explain underlying math, science and engineering concepts.&quot;<br /> * &quot;We have gleaned a number of tips from effective mentors who have participated in the Young Makers program [each one of these is fully fleshed out in the Playbook]: Help define scope; Help define schedules; Nurture note taking; Embrace failure and keep it safe; Avoid empty praise; Use your down-time well.&quot;<br /> <br /> <br /> '''Setup a website and/or a blog''' (p. 27)<br /> * &quot;''We strongly urge all clubs to create a website''. We also encourage every project team within a club to maintain a blog to track their project's progress. A website is a great tool to use to connect to your club members, as well as connecting to other blggs, and the greater community of Young Maker supporters... You can use it to document project made by your club, to recruit new members, and to maintain a schedule of build sessions.&quot;<br /> <br /> <br /> '''Come up with an identity''' (p. 27)<br /> * &quot;One advantage of a club is the opportunity to create a shared identity. Such things as adopting a mascot, designing a logo, having T-shirts made, having a website and picking a fun name can all help to create a sense of shared purpose and belonging. You'll probably want to pick an identity with member input, but don't spend too much valuable meeting time word-smithing your group's name. Then, in true Young Maker spirit, ask one of your Young Makers to create the logo and perhaps even manage the website. Some project teams may want to create a T-shirt to wear when they exhibit or present their work.&quot;<br /> <br /> <br /> '''Kick it off''' (pp. 29-30)<br /> * &quot;...[A]t the first meeting of the season, we have started with some low-key initiations: very brief introductions, then a little bit of making, and we end the gathering by giving all the new Young Makers brand new Maker's Notebooks where they can start jotting notes, making sketches and diagrams and recording things they find inspiring. We also ask that members sign an agreement that spells out the things they should expect of their experience and the commitments they've made. See the Resources section for a sample Participant Agreement.&quot;<br /> * &quot;You might also start your session with some ways to break the ice and also dig up helpful data.&quot;<br /> * &quot;Some goals for the kickoff meeting: 1) Introduce everyone; 2) Distribute notebooks or ask members to start them; 3) Get a sense of who is in the group, their skill level, and whether they have a project picked out; 4) Ask all participants to sign participation agreements.&quot;<br /> <br /> = Actions =<br /> {| class=&quot;wikitable&quot;<br /> !Action<br /> !Owner<br /> !Expected Date<br /> !Comments<br /> |-<br /> |Create a Meetup for the next meeting<br /> |<br /> |<br /> |<br /> |-<br /> |Start separate discussions on the Google group for the areas that need to be clarified<br /> |Steve U<br /> |<br /> |<br /> |-<br /> |Talk to Laura about the legal elements<br /> |Steve U<br /> |<br /> |<br /> |-<br /> |Contact details for [mailto:outreach-officer@eng.cam.ac.uk Maria Kettle] at Engineering Faculty<br /> |Meg W<br /> |<br /> |(MW) done - notes above<br /> |-<br /> |Contact friend at the [http://www.theroboticist.org/ Seattle kids' robotics club] for tips on setting up a club<br /> |Meg W<br /> |<br /> |(MW) done - waiting for reply<br /> |-<br /> |Define the steps to set the club up<br /> |<br /> |<br /> |<br /> |-<br /> |Define what we need to get access to the Makespace classroom<br /> |<br /> |<br /> |<br /> |-<br /> |Membership for Chris, Meg and Rod<br /> |Chris V, Meg W, Rod W<br /> |<br /> |<br /> |-<br /> |Risk assessments – what needs to be done?<br /> |<br /> |<br /> |<br /> |-<br /> |Do we need at least one founder in attendance?<br /> |<br /> |<br /> |<br /> |}</div>

JCGS http://wiki.makespace.org/Equipment/3D_Printer 2018-04-08T10:07:32Z

<p>JCGS: Correct the list of FDM printers.</p> <hr /> <div>[[Equipment|Equipment]] / 3D Printer<br /> <br /> = Introduction =<br /> FDM (filament deposition modelling) 3D printing is a way of creating small, custom objects from plastic filament. The printer melts the filament, held on a spool, and prints with it to create 3D structures. Makespace has four FDM printers, all of them Ultimaker 2. <br /> <br /> The Ultimaker 2 is now the only supported printer. Members trained to use the Makerbot may join a quick conversion session to be signed off to use Ultimaker rather than having to attend a new user Ultimaker session.<br /> <br /> = Equipment Pages =<br /> <br /> [[Equipment/3D_Printer/UM2|Ultimaker 2+ (PLA and ABS Printers)]]<br /> <br /> = Former (decommissioned) Equipment =<br /> <br /> These pages are included for historic purposes. The printers are no longer in use at Makespace.<br /> <br /> [[Equipment/3D_Printer/Makerbot|Makerbot Replicator 2X]]<br /> <br /> [[Equipment/3D_Printer/Up|UP!]]<br /> <br /> = General 3D Printing Resources =<br /> <br /> * [https://www.simplify3d.com/support/print-quality-troubleshooting/ Simplify's excellent 3D printing troubleshooting guide.]<br /> * [https://en.wikipedia.org/wiki/Fused_deposition_modeling Wikipedia entry for FDM printing]<br /> * [https://www.thingiverse.com/ Source of free CAD models for printing]<br /> * [https://3dfilaprint.com/ Web store for a wide variety of filaments] (5% discount code for MS members: cambmake)<br /> * [https://www.faberdashery.co.uk/ Web store specialising in good quality PLA filaments] (10% discount code for MS members: CAMMAKESPACE10)<br /> <br /> = Software =<br /> <br /> For machine specific software please visit the equipment pages linked above.<br /> <br /> * [http://sketchup.google.com/ Google SketchUp] with STL plugin as below<br /> ** [http://www.guitar-list.com/download-software/convert-sketchup-skp-files-dxf-or-stl This plugin] seems to work quite well. Use 'File/Export to DXF or STL' from Sketchup once you have installed it and select 'STL' as the last item in the type list when asked<br /> * [http://www.netfabb.com/ NetFabb] repairs any incomplete STL files<br /> * [http://meshlab.sourceforge.net/ Meshlab] is a good free program (Sourceforge) for visualising and modifying STL files<br /> * [http://www.openscad.org/ OpenSCAD] is a script-based modeller ('3D compiler'), well-suited for technical CAD (less so for artistic design)</div>

JCGS http://wiki.makespace.org/Classroom 2017-07-06T16:27:11Z

<p>JCGS: Make a page for the classroom; I was surprised there wasn't already one.</p> <hr /> <div>The classroom may be booked for meetings, through our [https://www.meetup.com/Makespace/ meetup.com] page.<br /> <br /> See also:<br /> <br /> * [[Classroom/Seating]]<br /> * [[Classroom/Projector]]<br /> * [[Events policy]]</div>

JCGS http://wiki.makespace.org/Makers_Social 2017-07-06T16:24:16Z

<p>JCGS: /* Purpose */</p> <hr /> <div>= Purpose =<br /> Maker Socials are social evenings hosted on the last Thursday of each month, and are an opportunity to meet other people without worrying so much about getting in the way of their hacking.<br /> The Social evening is focused on a buffet hosted in [[Cakespace]]. Although some food is provided at Makespace's expense, makers are welcome to bring in their own contributions if they see fit.<br /> <br /> == Planning ==<br /> There's normally some discussion of the social on the [https://groups.google.com/forum/#!forum/cammakespace google group]. If you want to run the buffet you are best advised to<br /> * Keep an eye out for competing activities, such as a beer fest<br /> * Read this guide, all of it, first.<br /> * Post to the group offering to run the buffet<br /> * ... preferably a couple of days in advance to see if anyone objects.<br /> * Arrange to see Mark Wainwright to discuss spending limits.<br /> If after all this you're still running the buffet, Hurrah!<br /> <br /> === Buffet ===<br /> Aiming to feed about a dozen people to the level of a small meal normally does the job quite nicely. Please remember that there will most likely be vegetarians in attendance.<br /> <br /> '''Never be afraid to pass off special offers as divine inspiration (Unless it's Corona.)'''<br /> <br /> The typical menu for the last few months has been:<br /> * A selection of fruit juices. Supermarkets tend to have at least one (own?)brand on a three-for-two or similar offer: Be inspired<br /> * Circular savoury things with farinaceous bases<br /> ** A vegetarian quiche or similar<br /> ** A meat-eaters quiche or similar<br /> ** A couple of vegetarian pizzas<br /> ** A couple of meat-eaters pizzas<br /> * Some packs of party nibbles (Savoury Eggs, Mini Sausage Rolls, etc.), half of which should be veggie.<br /> * Dips<br /> ** Coleslaw (Supermarket own brand)<br /> ** Potato Salad (See above)<br /> ** Tomatoish Tortilla chip dip.<br /> * One or two BIG bags of Tortilla chips. <br /> * Vegetables chopped up into finger food.<br /> ** Cherry Tomatoes (300g punnet does well enough.)<br /> ** Cucumber (One's enough)<br /> ** Bag of carrot batons<br /> ** Grapes<br /> * A few cook-at-home baguettes (perhaps including garlic bread)<br /> * A selection of cheeses, (three or four.)<br /> * Three or four varieties of biscuit/cracker to go with the cheese<br /> * Butter<br /> * Some sort of cake (this is commonly also brought by attendees).<br /> <br /> This is simply experience from running the social for a few months, experiments and refinements are welcome!<br /> <br /> === Alcohol ===<br /> Makespace is normally a dry zone, explicit permission must be sought from the directors before alcohol is consumed; start working on this a few days before the social.<br /> The rules require that<br /> * Tools or tagged equipment MUST NOT be used by people who have been drinking.<br /> * Only alcohol provided by the organiser can be consumed<br /> * It must be made clear that alcohol is only allowed on rare occasions.<br /> * At the end of the evening, any unused alcohol must be gathered and either <br /> ** Taken off site, <br /> ** Stored securely<br /> ** Explicitly marked &quot;For Social Nights Only.&quot; (In practice most people have finished by 23:00, so making this a formal end time is reasonable.)<br /> Before buying any alcohol check with Mark to see if there is any stored in the office from the previous social.<br /> Following a period of consultation and experimentation, it is recommended that a white wine and selection of reasonable Real Ales is offered. If you need guidance ask Mat Cook, and a certain supermarket is currently offering a &quot;Four for six quid&quot; deal, which keeps the cost down and ''Every Little Helps (Hint Hint)'' The same consultation period also concluded that there are certain beers that are not acceptable even if they are on special offer.<br /> <br /> == Execution ==<br /> <br /> You should be able to find enough for a reasonable spread at any major supermarket, expect to spend an hour or so dragging trolley around. <br /> <br /> === Schedule ===<br /> <br /> I've got away with setting up at about 19:30 without anyone grumbling, infact most people don't turn up until 20:15 ish.<br /> Advantages to setting up from 19:30 is that parking is easier, and you don't have to leave work early in order to get involved.<br /> If you're running the Buffet you should expect to be there till about mid-night.<br /> <br /> === Presentation ===<br /> <br /> The buffet is normally set up on the table in [[Cakespace]]; it could be set up on the counter overlooking the main space, but the table gives people something to cluster around. (Perhaps someone wants to run a &quot;Show And Tell&quot; where people set up projects on the table sometime?) Moving it to the [[Classroom]] to give room for more people, particularly if combined with a show-and-tell, has also been suggested.<br /> <br /> Have the drinks at the Fridge end of the table. <br /> Cake quite nicely goes next top that if there is any.<br /> There are a couple of &quot;Doughnut Shaped&quot; serving dishes with different compartments which are good for the veg, and crackers. They can go on next.<br /> After this it should just flow.<br /> <br /> === Clear Away ===<br /> <br /> Opened perishables (Cheese, Fruit juice etc) goes into a fridge in the fond hope that it will find sympathetic disposal. (We have starving artists for that kind of thing.)<br /> It's worth checking to see if there's anything going mouldy after a previous social, and deal with it. (On one occasion a potato salad started working on its own project.)<br /> Surplus Alcohol must be kept under control, this includes &quot;perishable&quot; wine. Best options for wine are either pour it down the drain or take it home for your own use, and haggle the<br /> bottle cost when filing the expenses receipt.</div>

JCGS http://wiki.makespace.org/Cakespace 2017-07-06T16:14:44Z

<p>JCGS: links re payments, to catch up with honesty boxes page</p> <hr /> <div>Cakespace is our [[Cakespace/kitchen|kitchen]] and [[Cakespace/sofa room|sofa room]].<br /> <br /> Snacks and drinks are available in the kitchen, paid for through an [[Honesty_boxes|honesty box]] or through an [http://www.izettle.com/ iZettle] online payment system.<br /> <br /> There used to be a non-rota for doing the [[shop run]] for food, but we now order online, and have the food delivered.<br /> <br /> For non-food supplies. add items to our [[Shopping List]].</div>

JCGS http://wiki.makespace.org/Online_payment_system 2017-07-06T16:12:53Z

<p>JCGS: /* Online payment */</p> <hr /> <div>There are a number of honesty boxes for consumables in Makespace, including for the [[Things_and_stuff#The_kitchen_(Cakespace) | kitchen]], [[Equipment/Laser_Cutter_Stock | lasercutters]], [[Equipment/3D_Printer | 3D printer]], [[Equipment/CNC_Router | CNC router]], [[Equipment/Vinyl_Cutter | vinyl cutter]], metalwork area ([[Equipment/Lathe | lathe]] and [[Equipment/WarcoMill | mill]]), and [[Equipment/VacuumFormer | vacuum former]].<br /> <br /> Rules regarding what must be paid for and how much will be made clear when you are inducted in the relevant equipment, and will probably also be displayed near the equipment or on its wiki page (see links above). If you are not sure, contact the owners or ask on the mailing list. Do not use consumables without paying.<br /> <br /> Note that you must pay for wasted material, not just your finished product. This is particularly relevant for the 3D printer. It is annoying to set up a print which goes wrong through no fault of your own, but you still need to pay for the filament used.<br /> <br /> In the case of the CNC router, although there is no communal stock, please remember that you still need to pay into the honesty box for using the communal cutters.<br /> <br /> == Ownership ==<br /> <br /> Money in the honesty boxes belongs to the Makespace community. It is up to the community and equipment owners to review whether the system is working and covering its costs, decide what to buy and when, etc. Consumables are not paid for by Makespace Ltd, but if there is a need for a new supply - e.g. a stock of consumables for a new piece of equipment - Makespace will usually 'seed' this with a one-off purchase or injection.<br /> <br /> Owners and others who pay for stock are an essential part of helping Makespace to run and should not end up out of pocket as a result. To help the system run:<br /> <br /> * always pay what you owe for your usage<br /> * check with owners before purchasing stock<br /> * if you nevertheless find you are out of pocket, contact the owners and the management to sort the problem out.<br /> <br /> == Overflow float ==<br /> <br /> Most of the honesty boxes have corresponding 'overflow' boxes in the office, and notes from the boxes in the main space are regularly emptied in order to avoid leaving significant amounts of money lying around.<br /> <br /> == Online payment ==<br /> <br /> We have an [http://www.izettle.com iZettle] online payment system in [[Cakespace]] (the kitchen) which can be used to pay for some materials as well as for drinks and snacks.</div>

JCGS http://wiki.makespace.org/Online_payment_system 2017-07-06T16:12:15Z

<p>JCGS: /* Online payment */ : linkify</p> <hr /> <div>There are a number of honesty boxes for consumables in Makespace, including for the [[Things_and_stuff#The_kitchen_(Cakespace) | kitchen]], [[Equipment/Laser_Cutter_Stock | lasercutters]], [[Equipment/3D_Printer | 3D printer]], [[Equipment/CNC_Router | CNC router]], [[Equipment/Vinyl_Cutter | vinyl cutter]], metalwork area ([[Equipment/Lathe | lathe]] and [[Equipment/WarcoMill | mill]]), and [[Equipment/VacuumFormer | vacuum former]].<br /> <br /> Rules regarding what must be paid for and how much will be made clear when you are inducted in the relevant equipment, and will probably also be displayed near the equipment or on its wiki page (see links above). If you are not sure, contact the owners or ask on the mailing list. Do not use consumables without paying.<br /> <br /> Note that you must pay for wasted material, not just your finished product. This is particularly relevant for the 3D printer. It is annoying to set up a print which goes wrong through no fault of your own, but you still need to pay for the filament used.<br /> <br /> In the case of the CNC router, although there is no communal stock, please remember that you still need to pay into the honesty box for using the communal cutters.<br /> <br /> == Ownership ==<br /> <br /> Money in the honesty boxes belongs to the Makespace community. It is up to the community and equipment owners to review whether the system is working and covering its costs, decide what to buy and when, etc. Consumables are not paid for by Makespace Ltd, but if there is a need for a new supply - e.g. a stock of consumables for a new piece of equipment - Makespace will usually 'seed' this with a one-off purchase or injection.<br /> <br /> Owners and others who pay for stock are an essential part of helping Makespace to run and should not end up out of pocket as a result. To help the system run:<br /> <br /> * always pay what you owe for your usage<br /> * check with owners before purchasing stock<br /> * if you nevertheless find you are out of pocket, contact the owners and the management to sort the problem out.<br /> <br /> == Overflow float ==<br /> <br /> Most of the honesty boxes have corresponding 'overflow' boxes in the office, and notes from the boxes in the main space are regularly emptied in order to avoid leaving significant amounts of money lying around.<br /> <br /> == Online payment ==<br /> <br /> We have an [http://www.izettle.com iZettle] online payment system in [Cakespace] (the kitchen) which can be used to pay for some materials as well as for drinks and snacks.</div>

JCGS http://wiki.makespace.org/Online_payment_system 2017-07-06T16:08:37Z

<p>JCGS: </p> <hr /> <div>There are a number of honesty boxes for consumables in Makespace, including for the [[Things_and_stuff#The_kitchen_(Cakespace) | kitchen]], [[Equipment/Laser_Cutter_Stock | lasercutters]], [[Equipment/3D_Printer | 3D printer]], [[Equipment/CNC_Router | CNC router]], [[Equipment/Vinyl_Cutter | vinyl cutter]], metalwork area ([[Equipment/Lathe | lathe]] and [[Equipment/WarcoMill | mill]]), and [[Equipment/VacuumFormer | vacuum former]].<br /> <br /> Rules regarding what must be paid for and how much will be made clear when you are inducted in the relevant equipment, and will probably also be displayed near the equipment or on its wiki page (see links above). If you are not sure, contact the owners or ask on the mailing list. Do not use consumables without paying.<br /> <br /> Note that you must pay for wasted material, not just your finished product. This is particularly relevant for the 3D printer. It is annoying to set up a print which goes wrong through no fault of your own, but you still need to pay for the filament used.<br /> <br /> In the case of the CNC router, although there is no communal stock, please remember that you still need to pay into the honesty box for using the communal cutters.<br /> <br /> == Ownership ==<br /> <br /> Money in the honesty boxes belongs to the Makespace community. It is up to the community and equipment owners to review whether the system is working and covering its costs, decide what to buy and when, etc. Consumables are not paid for by Makespace Ltd, but if there is a need for a new supply - e.g. a stock of consumables for a new piece of equipment - Makespace will usually 'seed' this with a one-off purchase or injection.<br /> <br /> Owners and others who pay for stock are an essential part of helping Makespace to run and should not end up out of pocket as a result. To help the system run:<br /> <br /> * always pay what you owe for your usage<br /> * check with owners before purchasing stock<br /> * if you nevertheless find you are out of pocket, contact the owners and the management to sort the problem out.<br /> <br /> == Overflow float ==<br /> <br /> Most of the honesty boxes have corresponding 'overflow' boxes in the office, and notes from the boxes in the main space are regularly emptied in order to avoid leaving significant amounts of money lying around.<br /> <br /> == Online payment ==<br /> <br /> We have an iZettle online payment system in Cakespace (the kitchen) which can be used to pay for some materials as well as for drinks and snacks.</div>

JCGS http://wiki.makespace.org/Induction 2017-03-24T09:58:35Z

<p>JCGS: Explain what induction is</p> <hr /> <div>For information on membership, see the [http://makespace.org/membership/ membership page] on the main website.<br /> <br /> The joining process includes a general induction to the space, including briefing on safety; for everyone's safety, you can't become a member until you've done this.<br /> <br /> [[Equipment/ToolClasses#RED| Many of our pieces of equipment]] also require specific training, which is sometimes referred to as induction.<br /> <br /> If you've been a member for long enough to know your way around and to know how things are done, do consider joining the inductors team (or becoming a trainer on a piece of equipment you are particularly familiar with). A good supply of induction and training sessions improves the experience of membership, especially for new members.</div>

JCGS http://wiki.makespace.org/Things_and_stuff 2017-03-23T14:09:38Z

<p>JCGS: /* Main space */</p> <hr /> <div>For larger items, see the [[Equipment]] page.<br /> <br /> This page is to help you to find smaller items, and to help you to put them back in the right place so others can find them. (Use the in-page search in your browser.)<br /> <br /> Some items have extra names in brackets after their usual name; please include all names that people might use to search for a particular item.<br /> <br /> ==The corridor==<br /> <br /> * Badger<br /> * Showcase<br /> * Cupboards including Arduinos, personal laser stock, Family Makers supplies<br /> * Lost property<br /> * [[Infrastructure/Member Personal Storage|Personal storage boxes]]<br /> <br /> ==The classroom==<br /> <br /> * [[Classroom/Projector|Projector]]<br /> * [[Classroom/Seating|Stacking chairs]]<br /> * Folding tables<br /> * Non-stacking, non-folding sofas<br /> <br /> ==Main space==<br /> <br /> {|<br /> |+ Main Space<br /> |-<br /> ! South<br /> ! aisle<br /> ! Central<br /> ! aisle<br /> ! North<br /> |-<br /> |<br /> | Windowsill<br /> | Door from corridor<br /> | Windowsill with landline phone<br /> |<br /> |-<br /> | [[Equipment/Glassworking|Glassworking kiln, torch and associated tools]]<br /> [[File:Glassworking.jpg]]<br /> * Kiln<br /> * Torch<br /> | [[Equipment/VacuumFormer|Vacuum Former]]<br /> [[File:Vacuum-former.jpg]]<br /> * Bike repair stuff is usually under this table<br /> |<br /> | Wire and components<br /> * Capacitors<br /> * Resistors<br /> * 74nn ICs (7400 series)<br /> * Wire<br /> | Electronics workbench<br /> * Insulating tape<br /> * Wire strippers<br /> * Pliers<br /> * Needle files<br /> * Screwdrivers<br /> |-<br /> | [[Equipment/Fine_metalwork_bench | Fine metalwork bench]]<br /> [[File:Fine-metalwork-bench.jpg]]<br /> * Dustbuster (small vacuum cleaner)<br /> * Flexible shaft tool<br /> * Scriber<br /> * Centre punch<br /> * Digital calipers (micrometer)<br /> * Flat Stake<br /> * Round triblet (for forming rings and suchlike)<br /> * Planishing Hammer (a polished-surface hammer for surface finishing and work-hardening)<br /> * Rawhide mallet (for hitting things without marking the surface)<br /> * Generic ball-pean hammer (a non-polished hammer for hitting punches etc.)<br /> |<br /> | Table<br /> |<br /> | Electronics workbench<br /> [[File:Electronics-workbenches.jpg]]<br /> On shelves:<br /> * BNC connectors, aerial connectors<br /> * More wire<br /> * Screwdrives, small pliers, etc<br /> * Stripboard<br /> * Solder suckers<br /> * Voltmeters<br /> * Soldering iron tips<br /> * PSUs (Power Supply Units)<br /> * Breadboards<br /> |-<br /> | Laser cutter stock<br /> [[File:Laser-stock.jpg]]<br /> * A grid of squares for measuring how much you've used (for the honesty box) is hung on the left-hand side of this<br /> |<br /> | Table<br /> [[File:White-table.jpg]]<br /> |<br /> | [[Equipment/Plotter|HP 750C A0 Plotter]]<br /> [[File:Plotter.jpg]]<br /> |-<br /> | Laser cutter computer<br /> [[File:Betsy-desk.jpg]]<br /> |<br /> |<br /> |<br /> | Ultimaker [[Equipment/3D_Printer|3D Printers (FDM)]]<br /> [[File:Ultimaker.jpg]]<br /> |-<br /> | [[Equipment/Laser_Cutter|Laser Cutter]]<br /> [[File:Betsy.jpg]]<br /> | Laser cutter computer<br /> [[File:Jaws-computer.jpg]]<br /> * Swarfega wipes<br /> | [[Equipment/Laser_Cutter|Laser Cutter]]<br /> [[File:Jaws.jpg]]<br /> |<br /> | Makerbot<br /> [[File:Makerbot.jpg]]<br /> * Printer thread<br /> |-<br /> | Formlabs 3D printer<br /> [[File:Formlabs.jpg]]<br /> |<br /> |<br /> |<br /> |<br /> * [[Equipment/CNC_Model_Mill|CNC Model Mill]]<br /> [[File:Roland-mill.jpg]]<br /> * Plates for model mill<br /> |-<br /> | Formlabs desk<br /> [[File:Chargers.jpg]]<br /> * Automatic plant watering system<br /> * AA (etc) battery chargers<br /> |<br /> | Table<br /> |<br /> | Sink area<br /> [[File:Sink-area.jpg]]<br /> * First aid kit<br /> * Eye washout kit<br /> * Torch<br /> * Cleaning cloths<br /> * Liquid soap<br /> * Swarfega<br /> * Fly spray (insecticide)<br /> * Watering can<br /> * Plant food (Baby Bio)<br /> |-<br /> | Desks<br /> [[File:Assorted-desk.jpg]]<br /> |<br /> | Table<br /> |<br /> | [[Equipment/Screenprinting|Screenprinting area]]<br /> [[File:Screen-printing-area.jpg]]<br /> * Screen printing equipment<br /> * Drying racks<br /> |-<br /> | <br /> |<br /> | Table<br /> [[File:Big-table.jpg]]<br /> <br /> General hacking area<br /> <br /> * Mains sockets<br /> * USB chargers<br /> |<br /> | Door to workshop<br /> |-<br /> | [[Equipment/Paper Printers|Paper printers]]<br /> [[File:Laser-printers.jpg]]<br /> * Paper<br /> * Stationery including pens, sellotape, whiteboard pens<br /> * CAT-5?<br /> |<br /> | Table<br /> |<br /> | Big shelves<br /> [[File:Deep-shelves.jpg]]<br /> * PPE (goggles, ear protectors, dustmasks)<br /> * PAT testing queue<br /> * Duct tape<br /> * Mains extension reels<br /> * PVA<br /> * Hot air guns (paint strippers)<br /> * Tape measures<br /> |-<br /> | Stair landing to kitchen<br /> | Stairs to kitchen<br /> | Plants and flat storage<br /> * Crimping tools<br /> * Craft knives<br /> * Cable ties<br /> * Rawlplugs<br /> * Watch batteries / button cells<br /> | Fire exit / door to big bins<br /> | Wood offcuts for recycling<br /> |}<br /> <br /> ==The workshop==<br /> <br /> ===West side===<br /> <br /> On the left as you go in:<br /> <br /> * Springs<br /> * Nuts and bolts, machine screws<br /> * Flat pencils<br /> * G-clamps<br /> * Battery charger for cordless tools<br /> * Vacuum cleaner (Henry)<br /> * Fretsaw<br /> * Chemicals cupboard (below worksurface): contains isopropyl alcohol for cleaning<br /> * [[Equipment/MitreSawRage3Db|Mitre Saw - Rage 3]]<br /> * [[Equipment/5704RK|Circular Saw - Makita ]]<br /> * [[Equipment/BandSaw|Band Saw]]<br /> * [[Equipment/CNC_Router|CNC Router]]<br /> <br /> ===Central island===<br /> <br /> * Steel rules, rulers, straight edges<br /> * Set squares<br /> * Spirit level<br /> <br /> In their own boxes under table:<br /> <br /> * Cordless drill<br /> * [[Equipment/5704RK|Circular Saw - Makita ]]<br /> * Jigsaw<br /> <br /> ===East side===<br /> <br /> On the right as you go in:<br /> <br /> * [[Equipment/WarcoMill|Mill - Warco ]]<br /> * [[Equipment/Lathe|Lathe - Myford]]<br /> * [[Equipment/Drill_Presses|Drill Presses]]<br /> * [[Equipment/Grinder|Grinder]]<br /> * Clamps<br /> * Pop rivets and rivet tool<br /> * Small nuts and bolts<br /> * Drill bits<br /> * [[Equipment/WoodLathe|Woodworking Lathe]]<br /> <br /> In storage bins:<br /> * Files<br /> * Screwdrivers<br /> * Allen keys (Hex keys)<br /> * Torx keys (Star screwdrivers)<br /> <br /> Hand tools on shadowboard:<br /> * Hammers<br /> * Hacksaws<br /> * Pliers<br /> <br /> ==The treasure trove==<br /> <br /> === Wall nearest door ===<br /> <br /> * Old disk drives including floppy drives<br /> <br /> === Near side of central shelves ===<br /> <br /> * Old audio / video stuff you could rebuild for something<br /> * Personal supplies of flat stuff that is too big for elsewhere<br /> * Old &quot;tower&quot; computer cases<br /> <br /> === Far side of central shelves ===<br /> <br /> * Electrical cables selection<br /> * Bits of cameras<br /> * Computer (ATX?) PSUs<br /> <br /> === Far shelves ===<br /> <br /> * Mains power supplies of many kinds<br /> * Fans<br /> * Capacitors<br /> * Resistors<br /> <br /> === Unclassified location ===<br /> <br /> * Various electrical connections and fittings<br /> * Multi-way mains extensions<br /> * Nabaztags (electric rabbits)<br /> * Just about anything for repurposing<br /> * Sledgehammer (broken handle, belongs to Visventis)<br /> <br /> ==The kitchen (Cakespace)==<br /> <br /> * Kettle<br /> * Oven<br /> * Microwave<br /> * Drinks<br /> * Snacks<br /> * Liquid soap<br /> * Cleaning materials<br /> * Bin bags<br /> <br /> ==Craft Room==<br /> <br /> * Vinyl cutter<br /> * Vinyl cutter stock<br /> * Eggbot<br /> * Knitting machine<br /> * Sewing machines<br /> * Thread<br /> * T-shirt press<br /> * Crafting table<br /> <br /> ==Unknown location==<br /> <br /> If you know where the things in this section are, please move their names to the appropriate section.</div>

JCGS http://wiki.makespace.org/Things_and_stuff 2017-03-23T14:08:08Z

<p>JCGS: /* Main space */</p> <hr /> <div>For larger items, see the [[Equipment]] page.<br /> <br /> This page is to help you to find smaller items, and to help you to put them back in the right place so others can find them. (Use the in-page search in your browser.)<br /> <br /> Some items have extra names in brackets after their usual name; please include all names that people might use to search for a particular item.<br /> <br /> ==The corridor==<br /> <br /> * Badger<br /> * Showcase<br /> * Cupboards including Arduinos, personal laser stock, Family Makers supplies<br /> * Lost property<br /> * [[Infrastructure/Member Personal Storage|Personal storage boxes]]<br /> <br /> ==The classroom==<br /> <br /> * [[Classroom/Projector|Projector]]<br /> * [[Classroom/Seating|Stacking chairs]]<br /> * Folding tables<br /> * Non-stacking, non-folding sofas<br /> <br /> ==Main space==<br /> <br /> {|<br /> |+ Main Space<br /> |-<br /> ! South<br /> ! aisle<br /> ! Central<br /> ! aisle<br /> ! North<br /> |-<br /> |<br /> | Windowsill<br /> | Door from corridor<br /> | Windowsill with landline phone<br /> |<br /> |-<br /> | [[Equipment/Glassworking|Glassworking kiln, torch and associated tools]]<br /> [[File:Glassworking.jpg]]<br /> * Kiln<br /> * Torch<br /> | [[Equipment/VacuumFormer|Vacuum Former]]<br /> [[File:Vacuum-former.jpg]]<br /> * Bike repair stuff is usually under this table<br /> |<br /> | Wire and components<br /> * Capacitors<br /> * Resistors<br /> * 74nn ICs (7400 series)<br /> * Wire<br /> | Electronics workbench<br /> * Insulating tape<br /> * Wire strippers<br /> * Pliers<br /> * Needle files<br /> * Screwdrivers<br /> |-<br /> | [[Equipment/Fine_metalwork_bench | Fine metalwork bench]]<br /> [[File:Fine-metalwork-bench.jpg]]<br /> * Dustbuster (small vacuum cleaner)<br /> * Flexible shaft tool<br /> * Scriber<br /> * Centre punch<br /> * Digital calipers (micrometer)<br /> * Flat Stake<br /> * Round triblet (for forming rings and suchlike)<br /> * Planishing Hammer (a polished-surface hammer for surface finishing and work-hardening)<br /> * Rawhide mallet (for hitting things without marking the surface)<br /> * Generic ball-pean hammer (a non-polished hammer for hitting punches etc.)<br /> |<br /> | Table<br /> |<br /> | Electronics workbench<br /> [[File:Electronics-workbenches.jpg]]<br /> On shelves:<br /> * BNC connectors, aerial connectors<br /> * More wire<br /> * Screwdrives, small pliers, etc<br /> * Stripboard<br /> * Solder suckers<br /> * Voltmeters<br /> * Soldering iron tips<br /> * PSUs (Power Supply Units)<br /> * Breadboards<br /> |-<br /> | Laser cutter stock<br /> [[File:Laser-stock.jpg]]<br /> * A grid of squares for measuring how much you've used (for the honesty box) is hung on the left-hand side of this<br /> |<br /> | Table<br /> [[File:White-table.jpg]]<br /> |<br /> | Plotter (largish inkjet)<br /> |-<br /> | Laser cutter computer<br /> [[File:Betsy-desk.jpg]]<br /> |<br /> |<br /> |<br /> | Ultimaker [[Equipment/3D_Printer|3D Printers (FDM)]]<br /> [[File:Ultimaker.jpg]]<br /> |-<br /> | [[Equipment/Laser_Cutter|Laser Cutter]]<br /> [[File:Betsy.jpg]]<br /> | Laser cutter computer<br /> [[File:Jaws-computer.jpg]]<br /> * Swarfega wipes<br /> | [[Equipment/Laser_Cutter|Laser Cutter]]<br /> [[File:Jaws.jpg]]<br /> |<br /> | Makerbot<br /> [[File:Makerbot.jpg]]<br /> * Printer thread<br /> |-<br /> | Formlabs 3D printer<br /> [[File:Formlabs.jpg]]<br /> |<br /> |<br /> |<br /> |<br /> * [[Equipment/CNC_Model_Mill|CNC Model Mill]]<br /> [[File:Roland-mill.jpg]]<br /> * Plates for model mill<br /> |-<br /> | Formlabs desk<br /> [[File:Chargers.jpg]]<br /> * Automatic plant watering system<br /> * AA (etc) battery chargers<br /> |<br /> | Table<br /> |<br /> | Sink area<br /> [[File:Sink-area.jpg]]<br /> * First aid kit<br /> * Eye washout kit<br /> * Torch<br /> * Cleaning cloths<br /> * Liquid soap<br /> * Swarfega<br /> * Fly spray (insecticide)<br /> * Watering can<br /> * Plant food (Baby Bio)<br /> |-<br /> | Desks<br /> [[File:Assorted-desk.jpg]]<br /> |<br /> | Table<br /> |<br /> | [[Equipment/Screenprinting|Screenprinting area]]<br /> [[File:Screen-printing-area.jpg]]<br /> * Screen printing equipment<br /> * Drying racks<br /> |-<br /> | [[Equipment/Plotter|HP 750C A0 Plotter]]<br /> [[File:Plotter.jpg]]<br /> |<br /> | Table<br /> [[File:Big-table.jpg]]<br /> <br /> General hacking area<br /> <br /> * Mains sockets<br /> * USB chargers<br /> |<br /> | Door to workshop<br /> |-<br /> | [[Equipment/Paper Printers|Paper printers]]<br /> [[File:Laser-printers.jpg]]<br /> * Paper<br /> * Stationery including pens, sellotape, whiteboard pens<br /> * CAT-5?<br /> |<br /> | Table<br /> |<br /> | Big shelves<br /> [[File:Deep-shelves.jpg]]<br /> * PPE (goggles, ear protectors, dustmasks)<br /> * PAT testing queue<br /> * Duct tape<br /> * Mains extension reels<br /> * PVA<br /> * Hot air guns (paint strippers)<br /> * Tape measures<br /> |-<br /> | Stair landing to kitchen<br /> | Stairs to kitchen<br /> | Plants and flat storage<br /> * Crimping tools<br /> * Craft knives<br /> * Cable ties<br /> * Rawlplugs<br /> * Watch batteries / button cells<br /> | Fire exit / door to big bins<br /> | Wood offcuts for recycling<br /> |}<br /> <br /> ==The workshop==<br /> <br /> ===West side===<br /> <br /> On the left as you go in:<br /> <br /> * Springs<br /> * Nuts and bolts, machine screws<br /> * Flat pencils<br /> * G-clamps<br /> * Battery charger for cordless tools<br /> * Vacuum cleaner (Henry)<br /> * Fretsaw<br /> * Chemicals cupboard (below worksurface): contains isopropyl alcohol for cleaning<br /> * [[Equipment/MitreSawRage3Db|Mitre Saw - Rage 3]]<br /> * [[Equipment/5704RK|Circular Saw - Makita ]]<br /> * [[Equipment/BandSaw|Band Saw]]<br /> * [[Equipment/CNC_Router|CNC Router]]<br /> <br /> ===Central island===<br /> <br /> * Steel rules, rulers, straight edges<br /> * Set squares<br /> * Spirit level<br /> <br /> In their own boxes under table:<br /> <br /> * Cordless drill<br /> * [[Equipment/5704RK|Circular Saw - Makita ]]<br /> * Jigsaw<br /> <br /> ===East side===<br /> <br /> On the right as you go in:<br /> <br /> * [[Equipment/WarcoMill|Mill - Warco ]]<br /> * [[Equipment/Lathe|Lathe - Myford]]<br /> * [[Equipment/Drill_Presses|Drill Presses]]<br /> * [[Equipment/Grinder|Grinder]]<br /> * Clamps<br /> * Pop rivets and rivet tool<br /> * Small nuts and bolts<br /> * Drill bits<br /> * [[Equipment/WoodLathe|Woodworking Lathe]]<br /> <br /> In storage bins:<br /> * Files<br /> * Screwdrivers<br /> * Allen keys (Hex keys)<br /> * Torx keys (Star screwdrivers)<br /> <br /> Hand tools on shadowboard:<br /> * Hammers<br /> * Hacksaws<br /> * Pliers<br /> <br /> ==The treasure trove==<br /> <br /> === Wall nearest door ===<br /> <br /> * Old disk drives including floppy drives<br /> <br /> === Near side of central shelves ===<br /> <br /> * Old audio / video stuff you could rebuild for something<br /> * Personal supplies of flat stuff that is too big for elsewhere<br /> * Old &quot;tower&quot; computer cases<br /> <br /> === Far side of central shelves ===<br /> <br /> * Electrical cables selection<br /> * Bits of cameras<br /> * Computer (ATX?) PSUs<br /> <br /> === Far shelves ===<br /> <br /> * Mains power supplies of many kinds<br /> * Fans<br /> * Capacitors<br /> * Resistors<br /> <br /> === Unclassified location ===<br /> <br /> * Various electrical connections and fittings<br /> * Multi-way mains extensions<br /> * Nabaztags (electric rabbits)<br /> * Just about anything for repurposing<br /> * Sledgehammer (broken handle, belongs to Visventis)<br /> <br /> ==The kitchen (Cakespace)==<br /> <br /> * Kettle<br /> * Oven<br /> * Microwave<br /> * Drinks<br /> * Snacks<br /> * Liquid soap<br /> * Cleaning materials<br /> * Bin bags<br /> <br /> ==Craft Room==<br /> <br /> * Vinyl cutter<br /> * Vinyl cutter stock<br /> * Eggbot<br /> * Knitting machine<br /> * Sewing machines<br /> * Thread<br /> * T-shirt press<br /> * Crafting table<br /> <br /> ==Unknown location==<br /> <br /> If you know where the things in this section are, please move their names to the appropriate section.</div>

JCGS http://wiki.makespace.org/Things_and_stuff 2017-03-23T14:06:53Z

<p>JCGS: Coathooks have been removed</p> <hr /> <div>For larger items, see the [[Equipment]] page.<br /> <br /> This page is to help you to find smaller items, and to help you to put them back in the right place so others can find them. (Use the in-page search in your browser.)<br /> <br /> Some items have extra names in brackets after their usual name; please include all names that people might use to search for a particular item.<br /> <br /> ==The corridor==<br /> <br /> * Badger<br /> * Showcase<br /> * Cupboards including Arduinos, personal laser stock, Family Makers supplies<br /> * Lost property<br /> * [[Infrastructure/Member Personal Storage|Personal storage boxes]]<br /> <br /> ==The classroom==<br /> <br /> * [[Classroom/Projector|Projector]]<br /> * [[Classroom/Seating|Stacking chairs]]<br /> * Folding tables<br /> * Non-stacking, non-folding sofas<br /> <br /> ==Main space==<br /> <br /> {|<br /> |+ Main Space<br /> |-<br /> ! South<br /> ! aisle<br /> ! Central<br /> ! aisle<br /> ! North<br /> |-<br /> |<br /> | Windowsill<br /> | Door from corridor<br /> | Windowsill with landline phone<br /> |<br /> |-<br /> | [[Equipment/Glassworking|Glassworking kiln, torch and associated tools]]<br /> [[File:Glassworking.jpg]]<br /> * Kiln<br /> * Torch<br /> | [[Equipment/VacuumFormer|Vacuum Former]]<br /> [[File:Vacuum-former.jpg]]<br /> * Bike repair stuff is usually under this table<br /> |<br /> | Wire and components<br /> * Capacitors<br /> * Resistors<br /> * 74nn ICs (7400 series)<br /> * Wire<br /> | Electronics workbench<br /> * Insulating tape<br /> * Wire strippers<br /> * Pliers<br /> * Needle files<br /> * Screwdrivers<br /> |-<br /> | [[Equipment/Fine_metalwork_bench | Fine metalwork bench]]<br /> [[File:Fine-metalwork-bench.jpg]]<br /> * Dustbuster (small vacuum cleaner)<br /> * Flexible shaft tool<br /> * Scriber<br /> * Centre punch<br /> * Digital calipers (micrometer)<br /> * Flat Stake<br /> * Round triblet (for forming rings and suchlike)<br /> * Planishing Hammer (a polished-surface hammer for surface finishing and work-hardening)<br /> * Rawhide mallet (for hitting things without marking the surface)<br /> * Generic ball-pean hammer (a non-polished hammer for hitting punches etc.)<br /> |<br /> | Table<br /> |<br /> | Electronics workbench<br /> [[File:Electronics-workbenches.jpg]]<br /> On shelves:<br /> * BNC connectors, aerial connectors<br /> * More wire<br /> * Screwdrives, small pliers, etc<br /> * Stripboard<br /> * Solder suckers<br /> * Voltmeters<br /> * Soldering iron tips<br /> * PSUs (Power Supply Units)<br /> * Breadboards<br /> |-<br /> | Laser cutter stock<br /> [[File:Laser-stock.jpg]]<br /> * A grid of squares for measuring how much you've used (for the honesty box) is hung on the left-hand side of this<br /> |<br /> | Table<br /> [[File:White-table.jpg]]<br /> |<br /> | Desk<br /> |-<br /> | Laser cutter computer<br /> [[File:Betsy-desk.jpg]]<br /> |<br /> |<br /> |<br /> | Ultimaker [[Equipment/3D_Printer|3D Printers (FDM)]]<br /> [[File:Ultimaker.jpg]]<br /> |-<br /> | [[Equipment/Laser_Cutter|Laser Cutter]]<br /> [[File:Betsy.jpg]]<br /> | Laser cutter computer<br /> [[File:Jaws-computer.jpg]]<br /> * Swarfega wipes<br /> | [[Equipment/Laser_Cutter|Laser Cutter]]<br /> [[File:Jaws.jpg]]<br /> |<br /> | Makerbot<br /> [[File:Makerbot.jpg]]<br /> * Printer thread<br /> |-<br /> | Formlabs 3D printer<br /> [[File:Formlabs.jpg]]<br /> |<br /> |<br /> |<br /> |<br /> * [[Equipment/CNC_Model_Mill|CNC Model Mill]]<br /> [[File:Roland-mill.jpg]]<br /> * Plates for model mill<br /> |-<br /> | Formlabs desk<br /> [[File:Chargers.jpg]]<br /> * Automatic plant watering system<br /> * AA (etc) battery chargers<br /> |<br /> | Table<br /> |<br /> | Sink area<br /> [[File:Sink-area.jpg]]<br /> * First aid kit<br /> * Eye washout kit<br /> * Torch<br /> * Cleaning cloths<br /> * Liquid soap<br /> * Swarfega<br /> * Fly spray (insecticide)<br /> * Watering can<br /> * Plant food (Baby Bio)<br /> |-<br /> | Desks<br /> [[File:Assorted-desk.jpg]]<br /> |<br /> | Table<br /> |<br /> | [[Equipment/Screenprinting|Screenprinting area]]<br /> [[File:Screen-printing-area.jpg]]<br /> * Screen printing equipment<br /> * Drying racks<br /> |-<br /> | [[Equipment/Plotter|HP 750C A0 Plotter]]<br /> [[File:Plotter.jpg]]<br /> |<br /> | Table<br /> [[File:Big-table.jpg]]<br /> <br /> General hacking area<br /> <br /> * Mains sockets<br /> * USB chargers<br /> |<br /> | Door to workshop<br /> |-<br /> | [[Equipment/Paper Printers|Paper printers]]<br /> [[File:Laser-printers.jpg]]<br /> * Paper<br /> * Stationery including pens, sellotape, whiteboard pens<br /> * CAT-5?<br /> |<br /> | Table<br /> |<br /> | Big shelves<br /> [[File:Deep-shelves.jpg]]<br /> * PPE (goggles, ear protectors, dustmasks)<br /> * PAT testing queue<br /> * Duct tape<br /> * Mains extension reels<br /> * PVA<br /> * Hot air guns (paint strippers)<br /> * Tape measures<br /> |-<br /> | Stair landing to kitchen<br /> | Stairs to kitchen<br /> | Plants and flat storage<br /> * Crimping tools<br /> * Craft knives<br /> * Cable ties<br /> * Rawlplugs<br /> * Watch batteries / button cells<br /> | Fire exit / door to big bins<br /> | Wood offcuts for recycling<br /> |}<br /> <br /> ==The workshop==<br /> <br /> ===West side===<br /> <br /> On the left as you go in:<br /> <br /> * Springs<br /> * Nuts and bolts, machine screws<br /> * Flat pencils<br /> * G-clamps<br /> * Battery charger for cordless tools<br /> * Vacuum cleaner (Henry)<br /> * Fretsaw<br /> * Chemicals cupboard (below worksurface): contains isopropyl alcohol for cleaning<br /> * [[Equipment/MitreSawRage3Db|Mitre Saw - Rage 3]]<br /> * [[Equipment/5704RK|Circular Saw - Makita ]]<br /> * [[Equipment/BandSaw|Band Saw]]<br /> * [[Equipment/CNC_Router|CNC Router]]<br /> <br /> ===Central island===<br /> <br /> * Steel rules, rulers, straight edges<br /> * Set squares<br /> * Spirit level<br /> <br /> In their own boxes under table:<br /> <br /> * Cordless drill<br /> * [[Equipment/5704RK|Circular Saw - Makita ]]<br /> * Jigsaw<br /> <br /> ===East side===<br /> <br /> On the right as you go in:<br /> <br /> * [[Equipment/WarcoMill|Mill - Warco ]]<br /> * [[Equipment/Lathe|Lathe - Myford]]<br /> * [[Equipment/Drill_Presses|Drill Presses]]<br /> * [[Equipment/Grinder|Grinder]]<br /> * Clamps<br /> * Pop rivets and rivet tool<br /> * Small nuts and bolts<br /> * Drill bits<br /> * [[Equipment/WoodLathe|Woodworking Lathe]]<br /> <br /> In storage bins:<br /> * Files<br /> * Screwdrivers<br /> * Allen keys (Hex keys)<br /> * Torx keys (Star screwdrivers)<br /> <br /> Hand tools on shadowboard:<br /> * Hammers<br /> * Hacksaws<br /> * Pliers<br /> <br /> ==The treasure trove==<br /> <br /> === Wall nearest door ===<br /> <br /> * Old disk drives including floppy drives<br /> <br /> === Near side of central shelves ===<br /> <br /> * Old audio / video stuff you could rebuild for something<br /> * Personal supplies of flat stuff that is too big for elsewhere<br /> * Old &quot;tower&quot; computer cases<br /> <br /> === Far side of central shelves ===<br /> <br /> * Electrical cables selection<br /> * Bits of cameras<br /> * Computer (ATX?) PSUs<br /> <br /> === Far shelves ===<br /> <br /> * Mains power supplies of many kinds<br /> * Fans<br /> * Capacitors<br /> * Resistors<br /> <br /> === Unclassified location ===<br /> <br /> * Various electrical connections and fittings<br /> * Multi-way mains extensions<br /> * Nabaztags (electric rabbits)<br /> * Just about anything for repurposing<br /> * Sledgehammer (broken handle, belongs to Visventis)<br /> <br /> ==The kitchen (Cakespace)==<br /> <br /> * Kettle<br /> * Oven<br /> * Microwave<br /> * Drinks<br /> * Snacks<br /> * Liquid soap<br /> * Cleaning materials<br /> * Bin bags<br /> <br /> ==Craft Room==<br /> <br /> * Vinyl cutter<br /> * Vinyl cutter stock<br /> * Eggbot<br /> * Knitting machine<br /> * Sewing machines<br /> * Thread<br /> * T-shirt press<br /> * Crafting table<br /> <br /> ==Unknown location==<br /> <br /> If you know where the things in this section are, please move their names to the appropriate section.</div>

JCGS http://wiki.makespace.org/Induction 2017-03-23T13:55:55Z

<p>JCGS: </p> <hr /> <div>For information on membership, see the [http://makespace.org/membership/ membership page] on the main website.<br /> <br /> If you've been a member for long enough to know your way around and to know how things are done, do consider joining the inductors team (or becoming a trainer on a piece of equipment you are particularly familiar with). A good supply of induction and training sessions improves the experience of new members.</div>

JCGS http://wiki.makespace.org/Makespace 2017-03-23T13:53:54Z

<p>JCGS: Remove the link to the members wall, as that ha some time ago.</p> <hr /> <div>[[File:WIP+Makespace-dan.png|thumb|frameless|400px|Makespace]]<br /> [http://makespace.org Makespace Homepage] / Wiki<br /> <br /> <br /> == New Wiki users ==<br /> <br /> Please request for your account to be activated on the mailing list. Thanks!<br /> <br /> <br /> == What is in Makespace? ==<br /> <br /> * '''[[Equipment|Our Equipment]]'''<br /> * [[Equipment Status]] (experimental page; may not be accurate)<br /> * [[Infrastructure]]<br /> * [[Things and stuff]] --- locator for smaller items<br /> <br /> == How does Makespace work? ==<br /> <br /> The space is great for individuals wanting to experiment, startups or companies wanting access to prototyping equipment, companies in the business who can come and do training and provide services beyond Makespace, and groups that want space to meet. Anyone who could benefit from a shared space focused on making things.<br /> <br /> At its core is a membership-based structure; the price of membership is £40/month inc VAT for full membership for 24/7 RFID access, or £33/month inc VAT for full student membership (no access outside of Cambridge university terms).<br /> <br /> It is a community run space; see:<br /> <br /> * [http://makespace.org Makespace Main Website]<br /> * [[Induction|Membership and inductions]]<br /> * [[Useful makespace info for Members]]<br /> * [[Policies]] - ie how stuff works<br /> * [[Latest member news]] - a great place to start if you want to find out what's been happening lately or what's coming up<br /> * Non-exhaustive [[People|list of people]] currently or previously involved.<br /> <br /> == Getting involved ==<br /> <br /> Members are encouraged, and non-members are welcome, to join our [http://groups.google.com/group/cammakespace mailing list]. You can read and post via the web interface or get messages delivered to your inbox.<br /> <br /> If you'd like to find out about upcoming real-world meetings, please join our [http://www.meetup.com/makespace Meetup] group.<br /> <br /> Members: please contribute to this wiki! If you spot something incomplete or out of date, just hit 'edit' and change it.<br /> <br /> We also have an IRC channel (not much used of late): join #makespace on Freenode in your IRC client or via your browser at http://webchat.freenode.net/?channels=makespace<br /> <br /> Various communication channels are listed [[Communications|here]].<br /> <br /> Consider becoming an Owner or Trainer.<br /> <br /> == Other information ==<br /> <br /> * [[Cakespace]]<br /> <br /> * [[How to do stuff for Makespace]]<br /> <br /> * [[Makespace member guidelines]]<br /> <br /> * Some information about other groups around the world that may be of interest can be found on the [[Links|Links page]].<br /> <br /> * Some projects may need external [[Service Suppliers]] for things we can't do in-house.<br /> <br /> == Regular groups ==<br /> <br /> There are regular meetings open to non-members on a variety of subjects. Or if not actually regular, at least repeated.<br /> <br /> * [[Family Makers]]<br /> * [[Raspberry Pi-makers]] and home automation<br /> * [[Arduino and Cake]] --- now merged with Raspberry Pi and home automation group<br /> * [[Robo-makers]] (is this still going?)<br /> * [[Things that fly]] --- quadcopters etc (is this still going? might be summer only)<br /> <br /> == Social Meetings ==<br /> <br /> There are always socials - and meetups and other things! The canonical means of arranging these is via Meetup: http://www.meetup.com/Makespace Check out [[Events policy|how to run an event in Makespace]].<br /> <br /> == Formal Meetings ==<br /> There are write-ups of planning and member meetings at [[Makespace/Meetings | Meetings]].<br /> <br /> == External meetings, conferences etc ==<br /> <br /> We list some [[external events]] that may be of interest to Makespace members.<br /> <br /> == Sponsorship and Donations! ==<br /> we're grateful to the founding sponsors who helped set Makespace up. Most current running costs are met from membership payments but we gratefully receive any donations, however small, that can help with developing, running and improving Makespace for everyone. Contact management (at) makespace (dot) org. Thanks!</div>

JCGS http://wiki.makespace.org/Makespace 2017-03-21T17:44:10Z

<p>JCGS: /* Other information */</p> <hr /> <div>[[File:WIP+Makespace-dan.png|thumb|frameless|400px|Makespace]]<br /> [http://makespace.org Makespace Homepage] / Wiki<br /> <br /> <br /> == New Wiki users ==<br /> <br /> Please request for your account to be activated on the mailing list. Thanks!<br /> <br /> <br /> == What is in Makespace? ==<br /> <br /> * '''[[Equipment|Our Equipment]]'''<br /> * [[Equipment Status]] (experimental page; may not be accurate)<br /> * [[Infrastructure]]<br /> * [[Things and stuff]] --- locator for smaller items<br /> <br /> == How does Makespace work? ==<br /> <br /> The space is great for individuals wanting to experiment, startups or companies wanting access to prototyping equipment, companies in the business who can come and do training and provide services beyond Makespace, and groups that want space to meet. Anyone who could benefit from a shared space focused on making things.<br /> <br /> At its core is a membership-based structure; the price of membership is £40/month inc VAT for full membership for 24/7 RFID access, or £33/month inc VAT for full student membership (no access outside of Cambridge university terms).<br /> <br /> It is a community run space; see:<br /> <br /> * [http://makespace.org Makespace Main Website]<br /> * [[Induction|Membership and inductions]]<br /> * [[Useful makespace info for Members]]<br /> * [[Policies]] - ie how stuff works<br /> * [[Latest member news]] - a great place to start if you want to find out what's been happening lately or what's coming up<br /> * Non-exhaustive [[People|list of people]] currently involved. Members are encouraged to post their details on the wall in the Makespace classroom. See also [[members wall]]<br /> <br /> == Getting involved ==<br /> <br /> Members are encouraged, and non-members are welcome, to join our [http://groups.google.com/group/cammakespace mailing list]. You can read and post via the web interface or get messages delivered to your inbox.<br /> <br /> If you'd like to find out about upcoming real-world meetings, please join our [http://www.meetup.com/makespace Meetup] group.<br /> <br /> Members: please contribute to this wiki! If you spot something incomplete or out of date, just hit 'edit' and change it.<br /> <br /> We also have an IRC channel (not much used of late): join #makespace on Freenode in your IRC client or via your browser at http://webchat.freenode.net/?channels=makespace<br /> <br /> Various communication channels are listed [[Communications|here]].<br /> <br /> Consider becoming an Owner or Trainer.<br /> <br /> == Other information ==<br /> <br /> * [[Cakespace]]<br /> <br /> * [[How to do stuff for Makespace]]<br /> <br /> * [[Makespace member guidelines]]<br /> <br /> * Some information about other groups around the world that may be of interest can be found on the [[Links|Links page]].<br /> <br /> * Some projects may need external [[Service Suppliers]] for things we can't do in-house.<br /> <br /> == Regular groups ==<br /> <br /> There are regular meetings open to non-members on a variety of subjects. Or if not actually regular, at least repeated.<br /> <br /> * [[Family Makers]]<br /> * [[Raspberry Pi-makers]] and home automation<br /> * [[Arduino and Cake]] --- now merged with Raspberry Pi and home automation group<br /> * [[Robo-makers]] (is this still going?)<br /> * [[Things that fly]] --- quadcopters etc (is this still going? might be summer only)<br /> <br /> == Social Meetings ==<br /> <br /> There are always socials - and meetups and other things! The canonical means of arranging these is via Meetup: http://www.meetup.com/Makespace Check out [[Events policy|how to run an event in Makespace]].<br /> <br /> == Formal Meetings ==<br /> There are write-ups of planning and member meetings at [[Makespace/Meetings | Meetings]].<br /> <br /> == External meetings, conferences etc ==<br /> <br /> We list some [[external events]] that may be of interest to Makespace members.<br /> <br /> == Sponsorship and Donations! ==<br /> we're grateful to the founding sponsors who helped set Makespace up. Most current running costs are met from membership payments but we gratefully receive any donations, however small, that can help with developing, running and improving Makespace for everyone. Contact management (at) makespace (dot) org. Thanks!</div>

JCGS http://wiki.makespace.org/Makespace 2017-03-21T17:41:53Z

<p>JCGS: /* Other information */</p> <hr /> <div>[[File:WIP+Makespace-dan.png|thumb|frameless|400px|Makespace]]<br /> [http://makespace.org Makespace Homepage] / Wiki<br /> <br /> <br /> == New Wiki users ==<br /> <br /> Please request for your account to be activated on the mailing list. Thanks!<br /> <br /> <br /> == What is in Makespace? ==<br /> <br /> * '''[[Equipment|Our Equipment]]'''<br /> * [[Equipment Status]] (experimental page; may not be accurate)<br /> * [[Infrastructure]]<br /> * [[Things and stuff]] --- locator for smaller items<br /> <br /> == How does Makespace work? ==<br /> <br /> The space is great for individuals wanting to experiment, startups or companies wanting access to prototyping equipment, companies in the business who can come and do training and provide services beyond Makespace, and groups that want space to meet. Anyone who could benefit from a shared space focused on making things.<br /> <br /> At its core is a membership-based structure; the price of membership is £40/month inc VAT for full membership for 24/7 RFID access, or £33/month inc VAT for full student membership (no access outside of Cambridge university terms).<br /> <br /> It is a community run space; see:<br /> <br /> * [http://makespace.org Makespace Main Website]<br /> * [[Induction|Membership and inductions]]<br /> * [[Useful makespace info for Members]]<br /> * [[Policies]] - ie how stuff works<br /> * [[Latest member news]] - a great place to start if you want to find out what's been happening lately or what's coming up<br /> * Non-exhaustive [[People|list of people]] currently involved. Members are encouraged to post their details on the wall in the Makespace classroom. See also [[members wall]]<br /> <br /> == Getting involved ==<br /> <br /> Members are encouraged, and non-members are welcome, to join our [http://groups.google.com/group/cammakespace mailing list]. You can read and post via the web interface or get messages delivered to your inbox.<br /> <br /> If you'd like to find out about upcoming real-world meetings, please join our [http://www.meetup.com/makespace Meetup] group.<br /> <br /> Members: please contribute to this wiki! If you spot something incomplete or out of date, just hit 'edit' and change it.<br /> <br /> We also have an IRC channel (not much used of late): join #makespace on Freenode in your IRC client or via your browser at http://webchat.freenode.net/?channels=makespace<br /> <br /> Various communication channels are listed [[Communications|here]].<br /> <br /> Consider becoming an Owner or Trainer.<br /> <br /> == Other information ==<br /> <br /> * [[Cakespace]]<br /> <br /> * [[How to do stuff for Makespace]]<br /> <br /> * [[Makespace member guidelines]]<br /> <br /> * Some information about other groups around the world that may be of interest can be found on the [[Links|Links page]].<br /> <br /> * Some projects may need external [[Service Suppliers]] for things we can't do in-house.<br /> <br /> <br /> There are regular meetings open to non-members on a variety of subjects.<br /> <br /> * [[Family Makers]]<br /> * [[Raspberry Pi-makers]]<br /> * [[Arduino and Cake]] --- now merged with Raspberry Pi and home automation group<br /> * [[Robo-makers]] (is this still going?)<br /> * [[Things that fly]] (is this still going? might be summer only)<br /> <br /> == Social Meetings ==<br /> <br /> There are always socials - and meetups and other things! The canonical means of arranging these is via Meetup: http://www.meetup.com/Makespace Check out [[Events policy|how to run an event in Makespace]].<br /> <br /> == Formal Meetings ==<br /> There are write-ups of planning and member meetings at [[Makespace/Meetings | Meetings]].<br /> <br /> == External meetings, conferences etc ==<br /> <br /> We list some [[external events]] that may be of interest to Makespace members.<br /> <br /> == Sponsorship and Donations! ==<br /> we're grateful to the founding sponsors who helped set Makespace up. Most current running costs are met from membership payments but we gratefully receive any donations, however small, that can help with developing, running and improving Makespace for everyone. Contact management (at) makespace (dot) org. Thanks!</div>

JCGS http://wiki.makespace.org/SeeTheSpace 2017-03-20T14:48:52Z

<p>JCGS: Add date of the lease we're currently working on</p> <hr /> <div>This is a See The Space guide for members to give to potential Makespace members.<br /> <br /> Intro<br /> * Set up with space donated by the University, funding from the government via Ideaspace, and created by the three dedicated idea people: Jonny, Simon and Laura.<br /> * It's a community - mutual help<br /> * Costs £40 per month (3 month minimum, 1 month's notice after that I think?)<br /> ** This pays only for the space (and 24/7 access with a keyfob) and the equipment.<br /> ** Training courses are run by volunteers, materials you use (eg acrylic) you pay for (or bring your own).<br /> ** Materials are extra - we don't make money on the honesty boxes<br /> ** There is no usage or hourly charge for anything<br /> * Concept of the owners for equipment - run by volunteers as part of the community spirit<br /> * Part of the community spirit of the place<br /> * We don't book equipment - just come along. BUT - if something is heavily used we buy two (eg Laser cutter)<br /> <br /> Ask their interests - what they want out of the space.<br /> <br /> Encourage questions from the start.<br /> <br /> Tour<br /> * Storage boxes for people (Makespace supplies a box and a space for everyone)<br /> * Classroom (events! gatherings! gaming nights! hackathons! electronics! presentations!)<br /> * Trove (partly free stuff, partly members' storage)<br /> * Main space<br /> ** Health and safety overview (it's not an induction - just be clear what we expect, tell them no touching before they're inducted)<br /> ** Honesty boxes to cover materials costs<br /> ** Community - tidying, helping each other, training<br /> ** Go through all major equipment<br /> ** Say what we're actively working to improve (but please don't make promises we can't definitely keep)<br /> ** Explain green/yellow/red kit, that they need to get inductions on red kit<br /> ** Enthuse about anything you love<br /> ** If you don't know much about something explain as such, and offer to put them in touch with the owner<br /> * Secure workshop<br /> ** Make sure it's safe to enter! (Ask anyone working in there to pause for a few minutes)<br /> * Thank our sponsors outside the kitchen, congratulate yourself if you're on it<br /> * Kitchen (please keep it tidy, honesty box)<br /> * Craft room - Vinyl cutter and TShirt press<br /> * Loos (explain the keyfob to get back in)<br /> <br /> Mention that we have this space for now, probably until the end of 2019, and after that we hope to find somewhere else close to Cambridge centre.<br /> <br /> Reconvene in the main space, ask if any more questions.<br /> <br /> They can sign up at makespace.org/membership (there might be a signup event right after the showing around - see if someone is running this)<br /> * They get a fob and a workspace induction, and then they can use the space whenever they wish.<br /> * Inductions on kit - please do ask for induction courses to be run!<br /> * Also: meetup.com, wiki, googlegroups.<br /> <br /> Tell them they're welcome to hang around after the tour and ask questions...</div>

JCGS http://wiki.makespace.org/Makespace 2017-03-20T14:47:12Z

<p>JCGS: /* Other information */</p> <hr /> <div>[[File:WIP+Makespace-dan.png|thumb|frameless|400px|Makespace]]<br /> [http://makespace.org Makespace Homepage] / Wiki<br /> <br /> <br /> == New Wiki users ==<br /> <br /> Please request for your account to be activated on the mailing list. Thanks!<br /> <br /> <br /> == What is in Makespace? ==<br /> <br /> * '''[[Equipment|Our Equipment]]'''<br /> * [[Equipment Status]] (experimental page; may not be accurate)<br /> * [[Infrastructure]]<br /> * [[Things and stuff]] --- locator for smaller items<br /> <br /> == How does Makespace work? ==<br /> <br /> The space is great for individuals wanting to experiment, startups or companies wanting access to prototyping equipment, companies in the business who can come and do training and provide services beyond Makespace, and groups that want space to meet. Anyone who could benefit from a shared space focused on making things.<br /> <br /> At its core is a membership-based structure; the price of membership is £40/month inc VAT for full membership for 24/7 RFID access, or £33/month inc VAT for full student membership (no access outside of Cambridge university terms).<br /> <br /> It is a community run space; see:<br /> <br /> * [http://makespace.org Makespace Main Website]<br /> * [[Induction|Membership and inductions]]<br /> * [[Useful makespace info for Members]]<br /> * [[Policies]] - ie how stuff works<br /> * [[Latest member news]] - a great place to start if you want to find out what's been happening lately or what's coming up<br /> * Non-exhaustive [[People|list of people]] currently involved. Members are encouraged to post their details on the wall in the Makespace classroom. See also [[members wall]]<br /> <br /> == Getting involved ==<br /> <br /> Members are encouraged, and non-members are welcome, to join our [http://groups.google.com/group/cammakespace mailing list]. You can read and post via the web interface or get messages delivered to your inbox.<br /> <br /> If you'd like to find out about upcoming real-world meetings, please join our [http://www.meetup.com/makespace Meetup] group.<br /> <br /> Members: please contribute to this wiki! If you spot something incomplete or out of date, just hit 'edit' and change it.<br /> <br /> We also have an IRC channel (not much used of late): join #makespace on Freenode in your IRC client or via your browser at http://webchat.freenode.net/?channels=makespace<br /> <br /> Various communication channels are listed [[Communications|here]].<br /> <br /> Consider becoming an Owner or Trainer.<br /> <br /> == Other information ==<br /> <br /> * [[Cakespace]]<br /> <br /> * [[How to do stuff for Makespace]]<br /> <br /> * [[Makespace member guidelines]]<br /> <br /> * Some information about other groups around the world that may be of interest can be found on the [[Links|Links page]].<br /> <br /> * Some projects may need external [[Service Suppliers]] for things we can't do in-house.<br /> <br /> <br /> There are regular meetings open to non-members on a variety of subjects.<br /> <br /> * [[Family Makers]]<br /> * [[Arduino and Cake]] --- now merged with Raspberry Pi and home automation group<br /> * [[Robo-makers]]<br /> * [[Things that fly]]<br /> <br /> == Social Meetings ==<br /> <br /> There are always socials - and meetups and other things! The canonical means of arranging these is via Meetup: http://www.meetup.com/Makespace Check out [[Events policy|how to run an event in Makespace]].<br /> <br /> == Formal Meetings ==<br /> There are write-ups of planning and member meetings at [[Makespace/Meetings | Meetings]].<br /> <br /> == External meetings, conferences etc ==<br /> <br /> We list some [[external events]] that may be of interest to Makespace members.<br /> <br /> == Sponsorship and Donations! ==<br /> we're grateful to the founding sponsors who helped set Makespace up. Most current running costs are met from membership payments but we gratefully receive any donations, however small, that can help with developing, running and improving Makespace for everyone. Contact management (at) makespace (dot) org. Thanks!</div>

JCGS http://wiki.makespace.org/Shop_run 2017-03-20T14:45:57Z

<p>JCGS: /* Shop run advice */</p> <hr /> <div>=This page is historic=<br /> <br /> We now order the supplies online, using a supermarket delivery service.<br /> <br /> =Shop run advice=<br /> <br /> When Cakespace food supplies run low (sometimes before they run low, sometimes after they run out), someone (this could be you) will drive to a supermarket and replenish the supplies, either taking cash in advance from the honesty box, or buying by card and claiming it back from the box. The established practice is to leave the receipt in the bottom of the cashbox.<br /> <br /> For non-food items check our [[Shopping List]]<br /> <br /> The main food groups are as follows:<br /> ; Fizzy drinks<br /> : Ordinary Coke is the most popular regularly available one. San Pellegrino (Aranciata etc) is very popular when you can get it cheaply enough to break even or better at our established rate of 50p per can.<br /> ; Chocolate bars etc<br /> : Classics like Mars seem to be most popular. Supermarkets' own brand clones don't go very well. Buy in multipacks (typically 7s) for economy.<br /> ; Crisps<br /> : Usual mixture<br /> ; Noodles e.g. Pot Noodles<br /> : a late addition to our range, which has gone down very well. If they're in cardboard trays on the shelves, pick up a few whole trays. You could also get some of the more &quot;proper oriental&quot; varieties, both in bowls and in packets. I've also got some soup sachets, but haven't checked how fast they're selling (summer 2014). They might go faster in colder weather; at least they'll keep well.<br /> <br /> I've tried getting yoghurt multipacks; these sell pretty slowly. Fruit hardly sells at all, and I suggest not bothering.<br /> <br /> ==Logistics==<br /> <br /> The combination of heavy items (e.g. multipacks of drink cans) being typically more robust and lighter ones (e.g. crisp packets) being typically more fragile, with the last-in-first-out nature of stacking in the trolley, is inconvenient. For a really big shop run, I've done a separate trolleyload of cans first, then gone back for the rest. If you have more than one person on the shop run, I suggest getting separate trolleys and one doing the drink cans and the other(s) the chocolates and the crisps.<br /> <br /> ===Asda===<br /> <br /> One of the Asda cashiers asked me suspiciously &quot;You're splitting those and reselling them, are you?&quot; as if I wasn't meant to do that. I said &quot;no&quot;, as strictly speaking I'm just leaving them on a shelf for other people to split. If they try that again, one might try &quot;Yes; please call a manager so I can explain why we'll take our trade elsewhere.&quot;<br /> <br /> The self-service checkout weighing device gets confused after about 60 quids' worth of cans are loaded onto it, and will then make a lot of complaints about unexpected items, etc (even more than usual).<br /> <br /> The self-service checkout cash input rejected a 50 note; I didn't experiment further, but took the next trolley-load to an attended checkout.<br /> <br /> =Turnover log=<br /> <br /> Please fill in how much you buy for Cakespace, and when, so we can get an idea of the turnover (with a view to planning online shopping orders).<br /> <br /> January 2014:<br /> <br /> JCGS about 100.00<br /> Two other people bought some, too.<br /> <br /> (This list seems to have been neglected for a while!)<br /> <br /> August 2014:<br /> <br /> JCGS about 208.00</div>

JCGS http://wiki.makespace.org/Shop_run 2017-03-20T14:45:18Z

<p>JCGS: Mark that we've switched to online ordering.</p> <hr /> <div>=This page is historic=<br /> <br /> We now order the supplies online, using a supermarket delivery service.<br /> <br /> =Shop run advice=<br /> <br /> When Cakespace food supplies run low (sometimes before they run low, sometimes after they run out), someone (this could be you) will drive to a supermarket and replenish the supplies, either taking cash in advance from the honesty box, or buying by card and claiming it back from the box. The established practice is to leave the receipt in the bottom of the cashbox.<br /> <br /> (for non-food items check our [[Shopping List]]<br /> <br /> The main food groups are as follows:<br /> ; Fizzy drinks<br /> : Ordinary Coke is the most popular regularly available one. San Pellegrino (Aranciata etc) is very popular when you can get it cheaply enough to break even or better at our established rate of 50p per can.<br /> ; Chocolate bars etc<br /> : Classics like Mars seem to be most popular. Supermarkets' own brand clones don't go very well. Buy in multipacks (typically 7s) for economy.<br /> ; Crisps<br /> : Usual mixture<br /> ; Noodles e.g. Pot Noodles<br /> : a late addition to our range, which has gone down very well. If they're in cardboard trays on the shelves, pick up a few whole trays. You could also get some of the more &quot;proper oriental&quot; varieties, both in bowls and in packets. I've also got some soup sachets, but haven't checked how fast they're selling (summer 2014). They might go faster in colder weather; at least they'll keep well.<br /> <br /> I've tried getting yoghurt multipacks; these sell pretty slowly. Fruit hardly sells at all, and I suggest not bothering.<br /> <br /> ==Logistics==<br /> <br /> The combination of heavy items (e.g. multipacks of drink cans) being typically more robust and lighter ones (e.g. crisp packets) being typically more fragile, with the last-in-first-out nature of stacking in the trolley, is inconvenient. For a really big shop run, I've done a separate trolleyload of cans first, then gone back for the rest. If you have more than one person on the shop run, I suggest getting separate trolleys and one doing the drink cans and the other(s) the chocolates and the crisps.<br /> <br /> ===Asda===<br /> <br /> One of the Asda cashiers asked me suspiciously &quot;You're splitting those and reselling them, are you?&quot; as if I wasn't meant to do that. I said &quot;no&quot;, as strictly speaking I'm just leaving them on a shelf for other people to split. If they try that again, one might try &quot;Yes; please call a manager so I can explain why we'll take our trade elsewhere.&quot;<br /> <br /> The self-service checkout weighing device gets confused after about 60 quids' worth of cans are loaded onto it, and will then make a lot of complaints about unexpected items, etc (even more than usual).<br /> <br /> The self-service checkout cash input rejected a 50 note; I didn't experiment further, but took the next trolley-load to an attended checkout.<br /> <br /> =Turnover log=<br /> <br /> Please fill in how much you buy for Cakespace, and when, so we can get an idea of the turnover (with a view to planning online shopping orders).<br /> <br /> January 2014:<br /> <br /> JCGS about 100.00<br /> Two other people bought some, too.<br /> <br /> (This list seems to have been neglected for a while!)<br /> <br /> August 2014:<br /> <br /> JCGS about 208.00</div>

JCGS http://wiki.makespace.org/Cakespace 2017-03-20T14:44:03Z

<p>JCGS: We've switched to using supermarket deliveries</p> <hr /> <div>Cakespace is our [[Cakespace/kitchen|kitchen]] and [[Cakespace/sofa room|sofa room]].<br /> <br /> Snacks and drinks are available in the kitchen, paid for through an honesty box or through an online payment system.<br /> <br /> There used to be a non-rota for doing the [[shop run]] for food, but we now order online, and have the food delivered.<br /> <br /> For non-food supplies. add items to our [[Shopping List]].</div>

JCGS http://wiki.makespace.org/Events_policy 2017-03-16T12:48:47Z

<p>JCGS: Update description of facilities to match the current arrangement.</p> <hr /> <div>== About this policy ==<br /> This policy is how things stand at present. If it doesn't work we'll change it!<br /> <br /> Related document: [[HostingSpeech|What hosts should tell people at the start of an open meeting]]<br /> <br /> = Steps to run an event =<br /> <br /> '''0. Be a member'''<br /> <br /> '''1. Follow the rules below'''<br /> <br /> '''2. Book the event on meetup: http://meetup.com/makespace so others know it's happening and won't book the space at the same time'''<br /> <br /> You can use meetup to advertise the event, or just use the Meetup calendar function to book the time. If your event is advertised by another group then just use the calendar (http://www.meetup.com/Makespace/events/); it gets confusing when there are two meetup events for the same meeting, and makes it hard to limit numbers to the maximum capacity.<br /> <br /> State clearly which bit of space you are booking: Main room, Classroom, Workshop or Upstairs.<br /> <br /> * If you're booking a meetup event, select the correct location (Makespace main room, Makespace classroom, etc).<br /> * If you're just using the calendar, please state the location information in the event name.<br /> * The classroom absolute maximum capacity is 60 seated, or 30 if you want tables; the main room holds around 100 standing. It is a good idea to limit meetup signup slots to reflect that.<br /> <br /> Note: you'll need to have organiser role for the Makespace meetup group to be able to edit the calendar. If you're not, either ask on the Google group to be made one, or find someone who is already an organiser.<br /> <br /> == General principles, or, how to host an event == <br /> <br /> * '''All members are welcome to organise an event at Makespace, and hosting an event is free of charge to members'''<br /> <br /> * '''Booking of rooms is generally handled via the makespace Meetup group.'''<br /> <br /> Say whether you are using the: main space; classroom; workshop; or cafe<br /> <br /> * If you aren't a member and you want to organise an event in Makespace, you either need to persuade members to host your event (by asking on the google group), or become a [http://makespace.org/membership member] yourself!'''<br /> <br /> * We strongly recommend that at least '''two''' members are happy to host an event, as this makes the event more likely to be a success.<br /> <br /> * If you have questions on how to host an event, the place to ask them is the makespace [https://groups.google.com/forum/?fromgroups#!forum/cammakespace mailing list].<br /> <br /> === Notes ===<br /> <br /> * '''For any event open to non-members, the usual rules about guests in the space apply.'''<br /> <br /> * '''Event organisers/hosts are always responsible for what happens at events.''' In other words, the members organising the event are responsible for the people attending and must be ready to handle emergencies, escort them out in case of fire, and if anything goes wrong (kit is broken or stolen, etc) the member(s) running the event will need to deal with the consequences as they will be held responsible.<br /> <br /> ''If a member brings in a few guests to show them around, have a meeting, work on a project etc, that's not an event, because it's all people the member knows and is escorting in the space - that's normal Makespace stuff :) '' <br /> <br /> '''Children''' attending the space should always be accompanied by a responsible adult; no more than 1 child per adult member or visitor (as it isn't always possible to supervise more than 1 child in a workshop situation). <br /> <br /> '''If you are NOT the organiser of an event''' you should NOT let non-members into the space unless the organiser has requested it of you directly. <br /> <br /> == If you want to run an event in Makespace and you are NOT a member ==<br /> <br /> Only Members can host events, so if you want to run an event you'll need one or more members to be willing to act as hosts. You could ask on our [https://groups.google.com/d/forum/cammakespace Google group] to see if anyone is interested in helping you, but we can't guarantee that anyone will be. <br /> <br /> Or, consider becoming a makespace member yourself!<br /> <br /> == Event types ==<br /> <br /> Events are either:<br /> <br /> * Members only<br /> * Open to the public (which may optionally include the opportunity to Meet Makespace, ie have a tour and ask questions about membership)<br /> <br /> '''Events listed on Meetup.com/makespace should clearly indicate whether they are Public, Members-only, or Meet-Makespace'''. Not all public events are ones where non-members can come and see the space and ask questions about membership and we need to clearly indicate those! <br /> <br /> === Members only events ===<br /> <br /> These events are organised by one or more members. <br /> <br /> * because everyone attending is a member, things are fairly straightforward<br /> * event may be anywhere in the space<br /> * if most of any one room in the space will be used and it won't be possible/nice/easy for other members to do stuff in that room whilst the event is happening, then the event should book the room(s) in advance on the calendar. <br /> * the event can be free or subject to a charge (the funds could pay for materials and/or a trainer's time or travel expenses etc, or could be donated to Makespace). If the event has a charge, the member(s) organising it are responsible for collecting the money and making any payments.<br /> * The event can be open to all members or restricted to just some members (for example, only members who have been trained on the 3D printer; only a fixed number of members; only specific members for some other reason). <br /> * '''No event should allow more than 100 people into the space at once.''' It may be useful to count people in on the door so you know when to stop admitting people. <br /> <br /> === Events open to the public ===<br /> <br /> These events are organised by one or more members but non-members are able to attend.<br /> <br /> * It's useful to run some sort of '''RSVP system''' so you aren't overwhelmed with people turning up unexpectedly. Whether you do or don't get an idea of numbers in advance, if more people turn up than the organisers or space can handle, the organisers MUST close the doors and not permit more people in. <br /> <br /> * remember, if you're the sole organiser, you have to be there or your event can't take place! You might want to make sure you can notify attendees if you are ill or unable to attend at the last minute. <br /> <br /> * We encourage events to be open to members if at all possible, and that members who happen to be in the space can attend events if possible. However we understand that sometimes this isn't possible, as some events may be restricted to just some members (for example, only members who have been trained on the 3D printer) or other limits may apply (such as a training event where the trainer can only work with up to 8 pre-booked learners, or a meeting is only open to people who have paid to attend, or where preparatory work is required). <br /> <br /> * Events may be free or subject to a charge (which may be either formal, eg &quot;£5 per person&quot;, or informal, eg &quot;please chip in a couple of quid if you can&quot;). ''It is totally fine and even good to charge non-members more than members.''<br /> <br /> <br /> '''Numbers of guests'''<br /> <br /> Depending on the number of people attending, there are requirements on how many members must be organising and attending the event. <br /> <br /> * For up to 10 guests, one member can organise the event '''but we strongly recommend at least two members organise any public event''' because it's really hard to keep an eye on everything when hosting an event; for up to 20 guests, two members; for up to 30 guests, 3 members, etc. <br /> <br /> * '''No event should allow more than 100 people into the space at once.''' It may be useful to count people in on the door so you know when to stop admitting people. <br /> <br /> * If the space feels overcrowded, immediately close the front door and do not permit more people to come in. <br /> <br /> <br /> '''Hosting a public event'''<br /> <br /> * Non-members attending your event should be encouraged to read the Visitors rules (posted at the internal door of makespace (NB not posted quite yet)) and to sign in the Visitors Book (if we have one) and to sign in on any sign-in sheet (see below).<br /> <br /> * Encourage non-members attending your event to take a Makespace card and consider becoming a member :) <br /> <br /> * If there are more than 10 non-members present, the organiser should give a brief housekeeping intro at the start of the event, pointing out fire exits, and potentially also other useful info (toilet location, first aid or other safety information that may be needed). See [[HostingSpeech]]<br /> <br /> * If your event is one where it's possible to Meet Makespace, please indicate that clearly. You'll need to either offer a tour before or after the main bit of your event (if it's something like a talk or demo), or have Members available to show people around throughout your event (if it's something like Maker Night). '''Note that this is time consuming and you should ensure you have plenty of Members involved in organising the event, so the event can happen as well as tours and questions!'''<br /> <br /> '''Doors'''<br /> <br /> * Beware - we often have non-members turning up FORTY minutes before an event is due to start! If you are NOT the organiser of an event, and you answer the doorbell, please DO NOT let people in unless the organiser has asked you to do so directly. Otherwise (and this has happened several times) an organiser who is still setting up ends up responsible for a bunch of non-members who have been let in far too early when the space isn't ready for them. <br /> <br /> * The exterior front door should not be propped open unless you have a member waiting in the foyer at all times<br /> <br /> * For larger events you may want to open the inner front door so that guests can let themselves out. DO NOT DO THIS if the exterior front door is propped open, or anyone could just walk into Makespace!<br /> <br /> * there is an access token in the cafe which can be used to give access to the toilets. for big events you might want to relocate the token to the corridor just outside the cafe so anyone returning from the toilets can let themselves in. If you do that when your event ends YOU MUST BRING THE TOKEN BACK IN TO MAKESPACE.<br /> <br /> == Big events and regular events and tracking attendance == <br /> <br /> Knowing who attends our events is important for Makespace to demonstrate its reach, which both meets the criteria of our bootstrap grant funding and is likely to unlock future funding opportunities. In particular we have a target to get 500 people each doing 6 hours of Makespace stuff!<br /> <br /> So, if your event is 6 hours or longer, '''please ensure you have a sign in sheet where everyone signs in with their full name and signs to confirm they are attending a 6+ hour event'''. Once you have this sheet completed please scan it or email an electronic copy to management@makespace.org, so we can report to our funders. <br /> <br /> If your event is less than 6 hours long but forms part of a series, for example, a course of 6 or more 1-hour talks or workshops, where you expect many people to attend the whole series, you will want to have a sign in sheet where it's easy to see how many events each person attended. You could use a matrix where each person signs in once and then ticks or signs for subsequent events. Again, once the course is complete (or you have lots of people who have done 6 hours of stuff) please scan it or email an electronic copy to management@makespace.org, so we can report to our funders.<br /> <br /> The target is 6 hours in total of engagement and this can be made up of one 6 hour block, several shorter blocks of time, whatever.<br /> <br /> <br /> == Publicity for events == <br /> <br /> * Events open to Members only can be advertised on the google group and/or on the Meetup group. It's essential that the event clearly indicates that it's members only. <br /> * Events open to the public can be advertised on the Meetup group<br /> <br /> You should only have one calling notice (i.e. Meetup event or similar) for each meeting:<br /> <br /> '''If it's a Makespace event''', the calendar entry will happen automatically when you create the event on the Makespace meetup group (you need to be a limited owner of the makespace group to be able to control the more subtle aspects of event registration).<br /> <br /> '''If the event is being organised by another group''', theirs should be the meetup group (or Eventbrite, or whatever else they use) publicising the event. The room in Makespace should be reserved by adding a calendar entry directly on the calendar tab of the Makespace events page. When you make the calendar entry, include the following information:<br /> * The event name<br /> * The start and end time<br /> * Your name/contact details<br /> * A link to the meeting's calling notice (if appropriate)<br /> <br /> <br /> For more details see [[MeetupEvent]]<br /> <br /> == Signage == <br /> <br /> If you are using the classroom or main space and you don't want other members wandering through make sure there's a sign outside to say what the event is and apologising for the inconvenience! If you are using the main space it's almost impossible for people not to wander through. <br /> <br /> <br /> == Space == <br /> <br /> * Whichever room the event is held in should be returned to its usual layout after the event. <br /> * '''Events are strongly preferred to take place in the classroom/meetspace''', especially if there's more than 10 people attending. Obviously some events may need to be in the main space (eg a 3D printer demo) but remember that use of the main space is more likely to inconvenience other members. (the same applies to events which use specific kit!) As a rule only general interest events which are agreed on list should use the whole main space. If in doubt use the classroom.<br /> * Make sure tables and chairs don't block the fire exits or the paths to them. If you are using the main space, ensure other members can still move between the workshop, cakespace etc. <br /> * Organisers are responsible for cleaning up after events and this should be done immediately after the event, not later in the day or the next morning. If you get food supplies in (e.g. pizza delivery to a hackathon) please take the packaging out to the large external recycling bins (outside the back door of the main space, and up the steps to your right) immediately after the event.<br /> <br /> '''The classroom''' has a set of folding tables and stacking chairs, and a projector mounted to the ceiling.<br /> <br /> '''Optionally we could alter this policy for all events to be in the classroom unless the google group or the directors agreed otherwise.'''<br /> <br /> == Food and drink == <br /> <br /> * Makespace doesn't provide catering. <br /> * Organisers can arrange food and drink, or use existing honesty box snacks and tea/coffee facilities.<br /> * Alcohol can only be served at events with the prior permission of the Directors. This applies even if there happens to be beer in the kitchen. <br /> <br /> == The Events calendar ==<br /> <br /> We generally divide each day into morning/afternoon/evening and book time against these slots but more specific times can be used if that helps. Please try to allow at least 30 minutes between two events to let one clear down and the next set up. <br /> <br /> Recurring events can occur:<br /> * every day at the same time<br /> * every week at the same time<br /> * every month at the same time ''defined by day of the week'' (eg 7pm on the second tuesday of each month)<br /> <br /> One-off events are also fine of course :) <br /> <br /> For now we will use the [http://meetup.makespace.org/events/calendar/#calendar Meetup group] to schedule events. (We also have a Google calendar but that's not currently in use for community run events)<br /> <br /> == Contention for space ==<br /> <br /> In the first instance it's first come first served! <br /> <br /> If you cannot find a good slot for your event, or there is already an event planned for the slot you want, contact the event organiser (this should be easy to do as they should be identified on the meetup.com listing for the event), and see if you can agree between yourselves who should have which slot. <br /> <br /> if you cannot find a slot for your event (for instance, you need an evening slot every 2 weeks and they are all full), email the Google group, and we'll discuss what should happen. If the group doesn't quickly reach a decision, the Directors may arbitrate between groups and may make a final decision if needed. <br /> <br /> Events are more likely to receive good slots if they:<br /> <br /> * are for members OR are training/outreach for potential new makespace community members<br /> * are makespace ish (see image at bottom of [http://makespace.org/index.php/space/principles/ Guiding Principles])<br /> * will pay money to makespace for the event<br /> <br /> If contention becomes endemic we will look at ways to manage this but we won't tackle this unless it's a problem.<br /> <br /> == If events cause you problems... ==<br /> If an event means you can't use the space or some kit you want to use, or otherwise is a notable inconvenience, or if people attending an event behave in a way which you feel is unsafe or abusive in any way, please let us know on the Google group or by emailing management@makespace so we can figure out if we need to alter this policy or take other action.</div>

JCGS http://wiki.makespace.org/External_events 2017-01-05T17:48:00Z

<p>JCGS: </p> <hr /> <div>Here are some meetings, conferences and camps outside of Makespace that may be of interest to members.<br /> <br /> == Conferences ==<br /> <br /> ; [http://www.fosdem.org FOSDEM]<br /> <br /> : The Free and Open Source Developers European Meeting happens annually in early February in Brussels. It covers software, hardware, legal and social issues, and beer. This is a very large conference.<br /> <br /> ; [http://oscal.openlabs.cc OSCAL]<br /> <br /> : The Open Source Conference Albania mostly covers open data, software and society. This is a small conference.<br /> <br /> == Maker faires==<br /> <br /> ; Maker Faire UK<br /> <br /> : [http://www.makerfaireuk.com/ Maker Faire UK] happens in the spring. Sometimes, there are also Mini Maker Faires.<br /> <br /> == Camps ==<br /> <br /> [http://www.emfcamp.org EMF Camp] happens in August in the UK on even-numbered calendar years; in the intervening years, [https://events.ccc.de Chaos Communication Camp] in Germany and camps of ever-varying names in the Netherlands happen alternately. 2015 was Germany's turn, 2017 is the Netherlands, this time under the name [https://sha2017.org/ SHA] (Shit Happens Anyway).</div>

JCGS http://wiki.makespace.org/External_events 2017-01-05T17:41:08Z

<p>JCGS: </p> <hr /> <div>Here are some meetings, conferences and camps outside of Makespace that may be of interest to members.<br /> <br /> == Conferences ==<br /> <br /> ; [http://www.fosdem.org FOSDEM]<br /> <br /> : The Free and Open Source Developers European Meeting happens annually in early February in Brussels. It covers software, hardware, legal and social issues, and beer. This is a very large conference.<br /> <br /> ; [http://oscal.openlabs.cc OSCAL]<br /> <br /> : The Open Source Conference Albania mostly covers open data, software and society. This is a small conference.<br /> <br /> == Maker faires==<br /> <br /> ; Maker Faire UK<br /> <br /> : [http://www.makerfaireuk.com/ Maker Faire UK] happens in the spring. Sometimes, there are also Mini Maker Faires.<br /> <br /> == Camps ==<br /> <br /> [http://www.emfcamp.org EMF Camp] happens in August in the UK on even-numbered calendar years; in the intervening years, [https://events.ccc.de Chaos Communication Camp] in Germany and camps of ever-varying names in the Netherlands happen alternately. 2015 was Germany's turn, 2017 is the Netherlands, this time under the name SHA (Shit Happens Anyway).</div>

JCGS http://wiki.makespace.org/Makespace 2017-01-05T17:37:31Z

<p>JCGS: Add external meetings</p> <hr /> <div>[[File:WIP+Makespace-dan.png|thumb|frameless|400px|Makespace]]<br /> [http://makespace.org Makespace Homepage] / Wiki<br /> <br /> <br /> == New Wiki users ==<br /> <br /> Please request for your account to be activated on the mailing list. Thanks!<br /> <br /> <br /> == What is in Makespace? ==<br /> <br /> * '''[[Equipment|Our Equipment]]'''<br /> * [[Equipment Status]] (experimental page; may not be accurate)<br /> * [[Infrastructure]]<br /> * [[Things and stuff]] --- locator for smaller items<br /> <br /> == How does Makespace work? ==<br /> <br /> The space is great for individuals wanting to experiment, startups or companies wanting access to prototyping equipment, companies in the business who can come and do training and provide services beyond Makespace, and groups that want space to meet. Anyone who could benefit from a shared space focused on making things.<br /> <br /> At its core is a membership-based structure; the price of membership is £40/month inc VAT for full membership for 24/7 RFID access, or £33/month inc VAT for full student membership (no access outside of Cambridge university terms).<br /> <br /> It is a community run space; see:<br /> <br /> * [http://makespace.org Makespace Main Website]<br /> * [[Induction|Membership and inductions]]<br /> * [[Useful makespace info for Members]]<br /> * [[Policies]] - ie how stuff works<br /> * [[Latest member news]] - a great place to start if you want to find out what's been happening lately or what's coming up<br /> * Non-exhaustive [[People|list of people]] currently involved. Members are encouraged to post their details on the wall in the Makespace classroom. See also [[members wall]]<br /> <br /> == Getting involved ==<br /> <br /> Members are encouraged, and non-members are welcome, to join our [http://groups.google.com/group/cammakespace mailing list]. You can read and post via the web interface or get messages delivered to your inbox.<br /> <br /> If you'd like to find out about upcoming real-world meetings, please join our [http://www.meetup.com/makespace Meetup] group.<br /> <br /> Members: please contribute to this wiki! If you spot something incomplete or out of date, just hit 'edit' and change it.<br /> <br /> We also have an IRC channel (not much used of late): join #makespace on Freenode in your IRC client or via your browser at http://webchat.freenode.net/?channels=makespace<br /> <br /> Various communication channels are listed [[Communications|here]].<br /> <br /> Consider becoming an Owner or Trainer.<br /> <br /> == Other information ==<br /> <br /> * [[Cakespace]]<br /> <br /> * [[How to do stuff for Makespace]]<br /> <br /> * [[Makespace member guidelines]]<br /> <br /> * Some information about other groups around the world that may be of interest can be found on the [[Links|Links page]].<br /> <br /> * Some projects may need external [[Service Suppliers]] for things we can't do in-house.<br /> <br /> <br /> There are regular meetings open to non-members on a variety of subjects.<br /> <br /> * [[Family Makers]]<br /> * [[Arduino and Cake]]<br /> * [[Robo-makers]]<br /> <br /> <br /> == Social Meetings ==<br /> <br /> There are always socials - and meetups and other things! The canonical means of arranging these is via Meetup: http://www.meetup.com/Makespace Check out [[Events policy|how to run an event in Makespace]].<br /> <br /> == Formal Meetings ==<br /> There are write-ups of planning and member meetings at [[Makespace/Meetings | Meetings]].<br /> <br /> == External meetings, conferences etc ==<br /> <br /> We list some [[external events]] that may be of interest to Makespace members.<br /> <br /> == Sponsorship and Donations! ==<br /> we're grateful to the founding sponsors who helped set Makespace up. Most current running costs are met from membership payments but we gratefully receive any donations, however small, that can help with developing, running and improving Makespace for everyone. Contact management (at) makespace (dot) org. Thanks!</div>

JCGS http://wiki.makespace.org/External_events 2017-01-05T17:36:58Z

<p>JCGS: Created page with &quot;Here are some meetings, conferences and camps outside of Makespace that may be of interest to members. == Conferences == ; [http://www.fosdem.org FOSDEM] : The Free and Ope...&quot;</p> <hr /> <div>Here are some meetings, conferences and camps outside of Makespace that may be of interest to members.<br /> <br /> == Conferences ==<br /> <br /> ; [http://www.fosdem.org FOSDEM]<br /> <br /> : The Free and Open Source Developers European Meeting happens annually in early February in Brussels. It covers software, hardware, legal and social issues, and beer. This is a very large conference.<br /> <br /> ; [http://oscal.openlabs.cc OSCAL]<br /> <br /> : The Open Source Conference Albania mostly covers open data, software and society. This is a small conference.<br /> <br /> == Maker faires==<br /> <br /> ; Maker Faire UK<br /> <br /> : [http://www.makerfaireuk.com/ Maker Faire UK] happens in the spring.<br /> <br /> == Camps ==<br /> <br /> [http://www.emfcamp.org EMF Camp] happens in August in the UK on even-numbered calendar years; in the intervening years, [https://events.ccc.de Chaos Communication Camp] in Germany and camps of ever-varying names in the Netherlands happen alternately. 2015 was Germany's turn, 2017 is the Netherlands, this time under the name SHA (Shit Happens Anyway).</div>

JCGS http://wiki.makespace.org/Arduino_and_Cake 2017-01-05T17:24:21Z

<p>JCGS: /* Merger with Raspberry Pi and home automation group = */</p> <hr /> <div>[[File:P1100161.jpg|200px|thumb|right|Cake!]]<br /> [[File:P1100164.jpg|200px|thumb|right|Arduino!]]<br /> [[File:P1100162.jpg|200px|thumb|right|Happy Hacking!]]<br /> [[File:P1100160.jpg|200px|thumb|right|The temperature sensor, it lives!]]<br /> [[File:P1100163.jpg|200px|thumb|right|Step step step...]]<br /> <br /> = Arduino and Cake =<br /> <br /> This is a page of information for the (hopefully) regular 'Arduino and Cake' event we run at Makespace. This is an evening where we get together in the space to learn and hack on projects involving the Arduino and similar microcontrollers. As the name suggests, there's also cake!<br /> <br /> If you're a complete beginner to microcontrollers (tiny, very cheap computers without an operating system, files, display, keyboard...) this is a great opportunity to come and play with them. Experts also very welcome, in fact we need you to help the new people! Possible things you can do with an Arduino (a particularly easy to use microcontroller board) range from simple flashing lights up to acting as the brains of an autonomous flying robot, managing your hydroponic gardening project or tweeting the current temperature of your hot water tank. This get-together is intended to help those of us for whom imagination exceeds expertise (that is to say, pretty much everyone I know), let's build cool things together :)<br /> <br /> == Merger with Raspberry Pi and home automation group ==<br /> <br /> Some time around 2015, the Arduino and Cake sessions stalled, and were subsumed into the Tuesday Raspberry Pi meetings.<br /> <br /> == New Sessions for 2014 - Return of the Cake ==<br /> <br /> After almost a year we're back, more cake, more flashing lights, more robots, but with no more clue or organisational skills! There are four events scheduled, culminating in one just before our [http://basebot.org/ robot] has to be ready for its competitive debut at the [http://piwars.org PiWars] event on the 6th of December (anyone who'd like to join us with that robot challenge is more than welcome!).<br /> <br /> Meetup pages for the events are as follows, all are 7pm to 10pm in the classroom:<br /> <br /> # [http://www.meetup.com/Makespace/events/218410302/ Wed 12th November]<br /> # [http://www.meetup.com/Makespace/events/218410332/ Thu 20th November]<br /> # [http://www.meetup.com/Makespace/events/218410402/ Fri 28th November]<br /> # [http://www.meetup.com/Makespace/events/218410442/ Thu 4th December] - Note change of date from Friday 5th!<br /> <br /> == Older Sessions ==<br /> <br /> The plan is to have this as regularly as possible, varying the day around in case people can't make a particular day of the week.<br /> <br /> # Our first session, with all levels of experience from complete novices to expert embedded programmers. Everyone paired up, with beginners and experts working together; judging from the happy buzz of making noises (both the noise of making, and the making of noises - we had buzzers!) it worked pretty well. The meetup page for the first go is [http://www.meetup.com/Makespace/events/130569572/ on meetup here]<br /> # The second one was on the 8th of August; meetup event [http://www.meetup.com/Makespace/events/132710342/ here], big copies of the photos (which are lurking on the right hand side of this very page) [http://www.flickr.com/photos/tomoinn/sets/72157634991866826/ here] :) Some of the bits for the Big Box of Breakout Boards and Bits arrived, temperature and humidity sensors and stepper motor drivers yielded to sugar driven curiosity.<br /> # The third was on the 16th August, slightly slower mostly as was distracted wiring cables but we made the dot matrix displays work (mostly) and Martin hacked some more on his sky tracking camera mount. Meetup event page [http://www.meetup.com/Makespace/events/134508292/ here]<br /> # The fourth was on the 28th August, no robots as we had some issues with the new Arduinos (it turned out later that they didn't have bootloaders, now fixed). The meetup event was [http://www.meetup.com/Makespace/events/135690182/ here]<br /> # The fith was in September 19th, meetup event was [http://www.meetup.com/Makespace/events/140024592/ here]<br /> <br /> Next meeting is Friday 25th October. Meetup page [http://www.meetup.com/Makespace/events/146064672/ here] - sign up! Bring cake! Bring friends! (particularly friends with cake) Make bleepy flashing things that run around the room!<br /> <br /> == Helpful links ==<br /> <br /> Arduino home page : [http://www.arduino.cc/ www.arduino.cc]&lt;br/&gt;<br /> A bunch of useful little circuits to play with: [http://www.pighixxx.com/abc-arduino-basic-connections/ Arduino Basic Connections]<br /> <br /> == Big Box of Breakout Boards and Bits (BBBBB) ==<br /> <br /> <br /> <br /> We've had approval to buy some bits and pieces for people to play with at this event, and generally within Makespace so I've done an eBay dive and ordered the following, these will arrive sometime over the next month or so:<br /> <br /> # {{Done|80 high brightness LEDs (20 each of orange, green, blue and pink!)}}<br /> # {{Done|4 LED Dot matrix modules with drivers}}<br /> # {{Done|2 Eight digit seven segment displays with drivers}}<br /> # {{Done|2 Ethernet shields for the Arduino Nano}}<br /> # {{Done|4 LCD 20x4 character displays}}<br /> # {{Done|8 Motion sensors (6 degrees of freedom MPU6050 based with 3 axis gyro and 3 axis accelerometer)}}<br /> # {{Done|6 Arduino Nano v3 boards (ATMega328, mounts on a breadboard)}}<br /> # {{Done|12 Dual H-bridge modules, used to drive regular and stepper motors}}<br /> # {{Done|3 Temperature / Relative humidity sensor modules}}<br /> # {{Done|2 IR correlation sensor modules (the kind where you have a beam which outputs a signal when broken, good for detecting rotation etc)}}<br /> # {{Done|10 Small servo motors (9g plastic type)}}<br /> # {{Done|6 Ultrasonic rangefinder modules, detect bounce from around 20cm to 3m}}<br /> # {{Done|4 Stepper motors with driver modules, 5v supply}}<br /> # {{Done|1 Barometric pressure sensor module}}<br /> # 10 Playstation style joysticks, the little analogue ones with a built in pushbutton on breakout boards<br /> # {{Done|10 NRF24L01 radio modules, short (~100m) range radio modules capable of transmitting packets of 3 bytes at around 2Mbits/second under ideal conditions}}<br /> # {{Done|A lot of somewhat longer jumper leads (20cm and 30cm) both male to male and male to female, the latter being particularly useful for connecting to the radio modules as they have a non-breadboard-friendly pin layout (or we can make boards with the PCB mill)}}<br /> <br /> Total budget for all the above including shipping is 270GBP (you get a lot of electronics for you money when buying from the far East!)<br /> <br /> As and when these appear at my house I'll bring them in and add them to the BBBBB - I'm planning to buy a decent size box with compartments to keep these in, both as convenient access and as a way to monitor attrition (these are cheap, but the cheapness comes with long lead times). These bits will be for use at Makespace, rather than for consumption but as long as we have enough items we can be flexible on that; I think if someone has ordered a Nano, say, there's no reason we can't lend them one of the kit ones while they wait for it to turn up.<br /> <br /> '''Update''' - we now have the box and some of the bits, I'm marking bits which have arrived and are now in the box in {{Done|this colour}} in the list above. At the moment the box is waiting to be documented and have the components properly marked, it'll then be left in Makespace and hopefully its contents won't evaporate too fast!<br /> <br /> '''Update 14th August 2013''' - The BBBBB has its own wiki page at [[Arduino and Cake/Big Box]] where we'll try to document everything as it arrives. Add information to that page if you find something interesting about a part we have, it's also the place to put requests for components and modules.<br /> <br /> '''Update 20th August 2013''' - More bits have arrived, we're almost complete! The next session should result in robots, or I'll be severely displeased.<br /> <br /> --[[User:Tomoinn|tmo]] 10:22, 20 August 2013 (BST)<br /> <br /> == Projects ==<br /> <br /> Got an interesting project or a project idea? Add it here.<br /> <br /> === Vehicle monitor / heating controller ===<br /> <br /> I've re-wired my Land Rover, using a star topology, with a big central &quot;ganglion&quot; which almost all the wires run to and from. There's an extra wire coming from each connection, that will go to a board of LEDs and voltage dividers, the latter feeding into an Arduino Mega, which will monitor just about everything, and display information on a small LCD panel.<br /> <br /> I'm also planning to make a motorized heater control system (moving flaps to direct air from an Eberspacher) and the valve motors will be driven from relays on the Arduino.<br /> <br /> And there'll be a GPS/GSM security unit, and eventually a Linux board (probably Pandaboard) running navigation software. And later on, I hope, an electric motor to drive the extra axle I added. The Arduino Mega will route data between all these points, with its multiple hardware UARTS, as well as sending out information it converts locally from its own inputs.<br /> <br /> I expect the software will be a main loop that polls all UARTs for incoming information, all wiring lines for changes from their previous state, all heating valve position sensors for whether they've reached the right position, all pedals for information to send to the traction motor controller when fitted, and does the associated actions (for example, NMEA sentences from the GPS get forwarded to the Linux board for navigation and are also used to display the time on the LCD, heating switches update the desired positions for flap valves).<br /> <br /> [[User:JCGS|JCGS]] 15:00, 2 August 2013 (BST)<br /> <br /> === Quadcopter ===<br /> <br /> Because everyone loves autonomous flying robots surrounded by razor sharp rotating propellers, right?<br /> <br /> A friend and I are working on a full self build of a quad rotor, we have the airframe, motors, props, speed controllers and an arduino with a combined gyro / accelerometer mounted. We just need to add batteries, wireless comms and software. I don't know whether I can persuade Si to come along to this meeting, he's not a member, but that's one of the things I'm playing with at the moment. I'm using the MPU6050 and PID libraries to manage the feedback between the accelerometer and the speed controllers in an attempt to get a stable hover mode, and the NRF24L01 as the radio module.<br /> <br /> --[[User:Tomoinn|tmo]] 15:12, 2 August 2013 (BST)<br /> <br /> === Bottle rocket telemetry ===<br /> <br /> The family makers are making bottle rockets, I thought it'd be cool to try to make a telemetry module that would tell them how high they'd gone and render a 3d trace of the trajectory using either Processing or WebGL. The main challenge here is to get the circuitry small enough and tough enough to be carried by the rockets and then survive the return to ground level! The second issue is power, I have a LiPo battery and charger so should just be a case of a 3.3v regulator but maybe it needs a boost converter, not really my area of expertise so I'd really like some help there.<br /> <br /> At the moment I'm interested in using an ATTiny85 (8 pin dip package MCU) as an Arduino, using the MPU6050 gyro / accelerometer and an XBee v2 radio - I'd use the NRF24 radio but I think it needs more pins than I have available on the ATTiny. Another option would be to use a rather more sophisticated Arduino pro mini, more pins means the NRF radio would be an option which is much cheaper than the XBee modules.<br /> <br /> --[[User:Tomoinn|tmo]] 15:12, 2 August 2013 (BST)<br /> <br /> === I2C plant moisture sensors ===<br /> <br /> Program an ATTiny85 as an I2C slave, embedding it onto a circuit board etched to work as a capacitive moisture sensor. Use Arduino nano with ethernet shield as an I2C master to then monitor the moisture levels in my various outdoor plant pots and tweet when they're getting too dry.<br /> <br /> --[[User:Tomoinn|tmo]] 15:12, 2 August 2013 (BST)<br /> <br /> === Breadboard prototype of a 1D Pong Game ===<br /> <br /> The idea is to prototype a simple 1D pong game (see [http://www.youtube.com/watch?v=kgQg1DVY4Xc YouTube]) on Arduino or other microcontroller.<br /> <br /> Features:<br /> *Some kind of startup animation (similar to the YouTube video)<br /> *A scoreboard or something similar. Based maybe on a segmented display or LCD.<br /> *SOUNDS! :-)<br /> *Perhaps some different game modes, maybe &quot;powerups&quot; of some kind?<br /> <br /> Eventually I would like this to be the start of a '''MUCH''' larger version of the game (but that's for the future ;-))<br /> <br /> --[[User:DannyG|DannyG]] 15:12, 2 August 2013 (BST)<br /> <br /> === Self-levelling camera gimbal ===<br /> <br /> One popular use of quadcopters is aerial photography/videography, but for this you ideally need a stabilised camera mounting. It's relatively easy to fabricate a two-axis gimbal for a small camera like a GoPro, driven by servos, which can hold itself level using readings from a gyro/accelerometer board.<br /> <br /> [[User:Martin de S|Martin de S]] 12:25, 13 August 2013 (BST)<br /> <br /> === Barn door sky tracker ===<br /> * Goal: take long exposure photos of the sky.<br /> * Problem: the sky rotates over the course of a long exposure.<br /> * Solution: make a motorised mount which rotates your camera at the same rate.<br /> <br /> I'm aiming to build a simple &quot;barn door&quot; mount (http://en.wikipedia.org/wiki/Barn_door_tracker) to enable me to take long exposure sky photos. At its simplest this is two hinged pieces of wood connected by a threaded rod which you turn slowly to increase the angle at the hinge. I'd like to drive this with a stepper motor so it can be left running, and ideally let the Arduino do some of the maths to compensate for the changing geometry of the mount.<br /> <br /> [[User:Martin de S|Martin de S]] 12:25, 13 August 2013 (BST)<br /> <br /> === Electricity monitor and TRIAC based resistive load driver ===<br /> <br /> I need to modulate a large resistive heating load on AC with a TRIAC: whole cycle and half cycle burst fire with some supervisory decision making process to make it comply with the EMC directives. I also need to monitor the power delivered by integrating current and voltage over the waveform and integrating the lot. It would be useful to estimate the supply impedance and/or internal resistance of the load using the same hardware. A lot of this is similar to work done on the Open Energy Monitor by the Solar-PV folks trying to game the tax system - with added EMC directives...<br /> <br /> [http://openenergymonitor.org/emon/]<br /> [http://openenergymonitor.org/emon/node/841]<br /> <br /> [[User:markocosic|markocosic]] 17:37, 21 August 2013 (BST)<br /> <br /> == Custom Arduino IDE Build ==<br /> <br /> I'm working on a custom version of the Arduino IDE to, amongst other things, allow us to cut and paste code from the IDE directly into this wiki. I've made that particular change on my own clone of the code, the adventurous can check it out from https://github.com/tomoinn/Arduino/tree/ide-1.5.x; you'll need to do the following (only tested on linux thus far!)<br /> <br /> &lt;span style='font-family:monospace; display: block; margin-left: 20px;'&gt;<br /> &gt; git clone git@github.com:tomoinn/Arduino.git&lt;br&gt;<br /> &gt; git checkout ide-1.5.x&lt;br&gt;<br /> &gt; cd Arduino/build&lt;br&gt;<br /> &gt; ant run<br /> &lt;/span&gt;<br /> <br /> You should then have a version of the IDE based on version 1.5 but with an extra context menu option 'copy as MediaWiki HTML', if you use this and then copy the clipboard into an editor in our wiki you should get something like the following:<br /> <br /> &lt;span style='font-family: monospace; display: block; margin-left: 10px; margin-right: 10px; margin-top: 10px; margin-bottom: 10px; padding: 6px; border: 1px solid #aaa; font-size: 12px; line-height: 15px;background-color: #f9f9f9;'&gt;&lt;span style='color: #7E7E7E;'&gt;/*&lt;/span&gt;&lt;br&gt;<br /> &lt;span style='color: #7E7E7E;'&gt;&amp;nbsp;&amp;nbsp;Blink&lt;/span&gt;&lt;br&gt;<br /> &lt;span style='color: #7E7E7E;'&gt;&amp;nbsp;Turns&amp;nbsp;on&amp;nbsp;an&amp;nbsp;LED&amp;nbsp;on&amp;nbsp;for&amp;nbsp;one&amp;nbsp;second,&amp;nbsp;then&amp;nbsp;off&amp;nbsp;for&amp;nbsp;one&amp;nbsp;second,&amp;nbsp;repeatedly.&lt;/span&gt;&lt;br&gt;<br /> &lt;span style='color: #7E7E7E;'&gt;&amp;nbsp;&lt;/span&gt;&lt;br&gt;<br /> &lt;span style='color: #7E7E7E;'&gt;&amp;nbsp;This&amp;nbsp;example&amp;nbsp;code&amp;nbsp;is&amp;nbsp;in&amp;nbsp;the&amp;nbsp;public&amp;nbsp;domain.&lt;/span&gt;&lt;br&gt;<br /> &lt;span style='color: #7E7E7E;'&gt;&amp;nbsp;*/&lt;/span&gt;&lt;br&gt;<br /> &lt;br&gt;<br /> &lt;span style='color: #7E7E7E;'&gt;//&amp;nbsp;Pin&amp;nbsp;13&amp;nbsp;has&amp;nbsp;an&amp;nbsp;LED&amp;nbsp;connected&amp;nbsp;on&amp;nbsp;most&amp;nbsp;Arduino&amp;nbsp;boards.&lt;/span&gt;&lt;br&gt;<br /> &lt;span style='color: #7E7E7E;'&gt;//&amp;nbsp;give&amp;nbsp;it&amp;nbsp;a&amp;nbsp;name:&lt;/span&gt;&lt;br&gt;<br /> &lt;span style='color: #CC6600;'&gt;int&lt;/span&gt; led = 13;&lt;br&gt;<br /> &lt;br&gt;<br /> &lt;span style='color: #7E7E7E;'&gt;//&amp;nbsp;the&amp;nbsp;setup&amp;nbsp;routine&amp;nbsp;runs&amp;nbsp;once&amp;nbsp;when&amp;nbsp;you&amp;nbsp;press&amp;nbsp;reset:&lt;/span&gt;&lt;br&gt;<br /> &lt;span style='color: #CC6600;'&gt;void&lt;/span&gt; &lt;span style='color: #CC6600;'&gt;&lt;b&gt;setup&lt;/b&gt;&lt;/span&gt;() { &lt;br&gt;<br /> &amp;nbsp;&amp;nbsp;&lt;span style='color: #7E7E7E;'&gt;// initialize the digital pin as an output.&lt;/span&gt;&lt;br&gt;<br /> &amp;nbsp;&amp;nbsp;&lt;span style='color: #CC6600;'&gt;pinMode&lt;/span&gt;(led, &lt;span style='color: #006699;'&gt;OUTPUT&lt;/span&gt;); &lt;br&gt;<br /> }&lt;br&gt;<br /> &lt;br&gt;<br /> &lt;span style='color: #7E7E7E;'&gt;//&amp;nbsp;the&amp;nbsp;loop&amp;nbsp;routine&amp;nbsp;runs&amp;nbsp;over&amp;nbsp;and&amp;nbsp;over&amp;nbsp;again&amp;nbsp;forever:&lt;/span&gt;&lt;br&gt;<br /> &lt;span style='color: #CC6600;'&gt;void&lt;/span&gt; &lt;span style='color: #CC6600;'&gt;&lt;b&gt;loop&lt;/b&gt;&lt;/span&gt;() {&lt;br&gt;<br /> &amp;nbsp;&amp;nbsp;&lt;span style='color: #CC6600;'&gt;digitalWrite&lt;/span&gt;(led, &lt;span style='color: #006699;'&gt;HIGH&lt;/span&gt;); &lt;span style='color: #7E7E7E;'&gt;// turn the LED on (HIGH is the voltage level)&lt;/span&gt;&lt;br&gt;<br /> &amp;nbsp;&amp;nbsp;&lt;span style='color: #CC6600;'&gt;delay&lt;/span&gt;(1000); &lt;span style='color: #7E7E7E;'&gt;// wait for a second&lt;/span&gt;&lt;br&gt;<br /> &amp;nbsp;&amp;nbsp;&lt;span style='color: #CC6600;'&gt;digitalWrite&lt;/span&gt;(led, &lt;span style='color: #006699;'&gt;LOW&lt;/span&gt;); &lt;span style='color: #7E7E7E;'&gt;// turn the LED off by making the voltage LOW&lt;/span&gt;&lt;br&gt;<br /> &amp;nbsp;&amp;nbsp;&lt;span style='color: #CC6600;'&gt;delay&lt;/span&gt;(1000); &lt;span style='color: #7E7E7E;'&gt;// wait for a second&lt;/span&gt;&lt;br&gt;<br /> }&lt;br&gt;<br /> &lt;/span&gt;<br /> <br /> Should make putting example code up easier - I'm also thinking of customizing colours, logo etc to create a makespace edition of the IDE. As and when it becomes a bit more stable I'll start doing proper builds for linux and windows at least. Note that cloning the github repository takes a long time, it's going on for 600Mb of data, potentially you can cut that down by only cloning the ide-1.5.x branch if you're familiar with git.<br /> <br /> --[[User:Tomoinn|tmo]] 14:09, 13 September 2013 (BST)</div>

JCGS http://wiki.makespace.org/Arduino_and_Cake 2017-01-05T17:24:09Z

<p>JCGS: </p> <hr /> <div>[[File:P1100161.jpg|200px|thumb|right|Cake!]]<br /> [[File:P1100164.jpg|200px|thumb|right|Arduino!]]<br /> [[File:P1100162.jpg|200px|thumb|right|Happy Hacking!]]<br /> [[File:P1100160.jpg|200px|thumb|right|The temperature sensor, it lives!]]<br /> [[File:P1100163.jpg|200px|thumb|right|Step step step...]]<br /> <br /> = Arduino and Cake =<br /> <br /> This is a page of information for the (hopefully) regular 'Arduino and Cake' event we run at Makespace. This is an evening where we get together in the space to learn and hack on projects involving the Arduino and similar microcontrollers. As the name suggests, there's also cake!<br /> <br /> If you're a complete beginner to microcontrollers (tiny, very cheap computers without an operating system, files, display, keyboard...) this is a great opportunity to come and play with them. Experts also very welcome, in fact we need you to help the new people! Possible things you can do with an Arduino (a particularly easy to use microcontroller board) range from simple flashing lights up to acting as the brains of an autonomous flying robot, managing your hydroponic gardening project or tweeting the current temperature of your hot water tank. This get-together is intended to help those of us for whom imagination exceeds expertise (that is to say, pretty much everyone I know), let's build cool things together :)<br /> <br /> == Merger with Raspberry Pi and home automation group ===<br /> <br /> Some time around 2015, the Arduino and Cake sessions stalled, and were subsumed into the Tuesday Raspberry Pi meetings.<br /> <br /> == New Sessions for 2014 - Return of the Cake ==<br /> <br /> After almost a year we're back, more cake, more flashing lights, more robots, but with no more clue or organisational skills! There are four events scheduled, culminating in one just before our [http://basebot.org/ robot] has to be ready for its competitive debut at the [http://piwars.org PiWars] event on the 6th of December (anyone who'd like to join us with that robot challenge is more than welcome!).<br /> <br /> Meetup pages for the events are as follows, all are 7pm to 10pm in the classroom:<br /> <br /> # [http://www.meetup.com/Makespace/events/218410302/ Wed 12th November]<br /> # [http://www.meetup.com/Makespace/events/218410332/ Thu 20th November]<br /> # [http://www.meetup.com/Makespace/events/218410402/ Fri 28th November]<br /> # [http://www.meetup.com/Makespace/events/218410442/ Thu 4th December] - Note change of date from Friday 5th!<br /> <br /> == Older Sessions ==<br /> <br /> The plan is to have this as regularly as possible, varying the day around in case people can't make a particular day of the week.<br /> <br /> # Our first session, with all levels of experience from complete novices to expert embedded programmers. Everyone paired up, with beginners and experts working together; judging from the happy buzz of making noises (both the noise of making, and the making of noises - we had buzzers!) it worked pretty well. The meetup page for the first go is [http://www.meetup.com/Makespace/events/130569572/ on meetup here]<br /> # The second one was on the 8th of August; meetup event [http://www.meetup.com/Makespace/events/132710342/ here], big copies of the photos (which are lurking on the right hand side of this very page) [http://www.flickr.com/photos/tomoinn/sets/72157634991866826/ here] :) Some of the bits for the Big Box of Breakout Boards and Bits arrived, temperature and humidity sensors and stepper motor drivers yielded to sugar driven curiosity.<br /> # The third was on the 16th August, slightly slower mostly as was distracted wiring cables but we made the dot matrix displays work (mostly) and Martin hacked some more on his sky tracking camera mount. Meetup event page [http://www.meetup.com/Makespace/events/134508292/ here]<br /> # The fourth was on the 28th August, no robots as we had some issues with the new Arduinos (it turned out later that they didn't have bootloaders, now fixed). The meetup event was [http://www.meetup.com/Makespace/events/135690182/ here]<br /> # The fith was in September 19th, meetup event was [http://www.meetup.com/Makespace/events/140024592/ here]<br /> <br /> Next meeting is Friday 25th October. Meetup page [http://www.meetup.com/Makespace/events/146064672/ here] - sign up! Bring cake! Bring friends! (particularly friends with cake) Make bleepy flashing things that run around the room!<br /> <br /> == Helpful links ==<br /> <br /> Arduino home page : [http://www.arduino.cc/ www.arduino.cc]&lt;br/&gt;<br /> A bunch of useful little circuits to play with: [http://www.pighixxx.com/abc-arduino-basic-connections/ Arduino Basic Connections]<br /> <br /> == Big Box of Breakout Boards and Bits (BBBBB) ==<br /> <br /> <br /> <br /> We've had approval to buy some bits and pieces for people to play with at this event, and generally within Makespace so I've done an eBay dive and ordered the following, these will arrive sometime over the next month or so:<br /> <br /> # {{Done|80 high brightness LEDs (20 each of orange, green, blue and pink!)}}<br /> # {{Done|4 LED Dot matrix modules with drivers}}<br /> # {{Done|2 Eight digit seven segment displays with drivers}}<br /> # {{Done|2 Ethernet shields for the Arduino Nano}}<br /> # {{Done|4 LCD 20x4 character displays}}<br /> # {{Done|8 Motion sensors (6 degrees of freedom MPU6050 based with 3 axis gyro and 3 axis accelerometer)}}<br /> # {{Done|6 Arduino Nano v3 boards (ATMega328, mounts on a breadboard)}}<br /> # {{Done|12 Dual H-bridge modules, used to drive regular and stepper motors}}<br /> # {{Done|3 Temperature / Relative humidity sensor modules}}<br /> # {{Done|2 IR correlation sensor modules (the kind where you have a beam which outputs a signal when broken, good for detecting rotation etc)}}<br /> # {{Done|10 Small servo motors (9g plastic type)}}<br /> # {{Done|6 Ultrasonic rangefinder modules, detect bounce from around 20cm to 3m}}<br /> # {{Done|4 Stepper motors with driver modules, 5v supply}}<br /> # {{Done|1 Barometric pressure sensor module}}<br /> # 10 Playstation style joysticks, the little analogue ones with a built in pushbutton on breakout boards<br /> # {{Done|10 NRF24L01 radio modules, short (~100m) range radio modules capable of transmitting packets of 3 bytes at around 2Mbits/second under ideal conditions}}<br /> # {{Done|A lot of somewhat longer jumper leads (20cm and 30cm) both male to male and male to female, the latter being particularly useful for connecting to the radio modules as they have a non-breadboard-friendly pin layout (or we can make boards with the PCB mill)}}<br /> <br /> Total budget for all the above including shipping is 270GBP (you get a lot of electronics for you money when buying from the far East!)<br /> <br /> As and when these appear at my house I'll bring them in and add them to the BBBBB - I'm planning to buy a decent size box with compartments to keep these in, both as convenient access and as a way to monitor attrition (these are cheap, but the cheapness comes with long lead times). These bits will be for use at Makespace, rather than for consumption but as long as we have enough items we can be flexible on that; I think if someone has ordered a Nano, say, there's no reason we can't lend them one of the kit ones while they wait for it to turn up.<br /> <br /> '''Update''' - we now have the box and some of the bits, I'm marking bits which have arrived and are now in the box in {{Done|this colour}} in the list above. At the moment the box is waiting to be documented and have the components properly marked, it'll then be left in Makespace and hopefully its contents won't evaporate too fast!<br /> <br /> '''Update 14th August 2013''' - The BBBBB has its own wiki page at [[Arduino and Cake/Big Box]] where we'll try to document everything as it arrives. Add information to that page if you find something interesting about a part we have, it's also the place to put requests for components and modules.<br /> <br /> '''Update 20th August 2013''' - More bits have arrived, we're almost complete! The next session should result in robots, or I'll be severely displeased.<br /> <br /> --[[User:Tomoinn|tmo]] 10:22, 20 August 2013 (BST)<br /> <br /> == Projects ==<br /> <br /> Got an interesting project or a project idea? Add it here.<br /> <br /> === Vehicle monitor / heating controller ===<br /> <br /> I've re-wired my Land Rover, using a star topology, with a big central &quot;ganglion&quot; which almost all the wires run to and from. There's an extra wire coming from each connection, that will go to a board of LEDs and voltage dividers, the latter feeding into an Arduino Mega, which will monitor just about everything, and display information on a small LCD panel.<br /> <br /> I'm also planning to make a motorized heater control system (moving flaps to direct air from an Eberspacher) and the valve motors will be driven from relays on the Arduino.<br /> <br /> And there'll be a GPS/GSM security unit, and eventually a Linux board (probably Pandaboard) running navigation software. And later on, I hope, an electric motor to drive the extra axle I added. The Arduino Mega will route data between all these points, with its multiple hardware UARTS, as well as sending out information it converts locally from its own inputs.<br /> <br /> I expect the software will be a main loop that polls all UARTs for incoming information, all wiring lines for changes from their previous state, all heating valve position sensors for whether they've reached the right position, all pedals for information to send to the traction motor controller when fitted, and does the associated actions (for example, NMEA sentences from the GPS get forwarded to the Linux board for navigation and are also used to display the time on the LCD, heating switches update the desired positions for flap valves).<br /> <br /> [[User:JCGS|JCGS]] 15:00, 2 August 2013 (BST)<br /> <br /> === Quadcopter ===<br /> <br /> Because everyone loves autonomous flying robots surrounded by razor sharp rotating propellers, right?<br /> <br /> A friend and I are working on a full self build of a quad rotor, we have the airframe, motors, props, speed controllers and an arduino with a combined gyro / accelerometer mounted. We just need to add batteries, wireless comms and software. I don't know whether I can persuade Si to come along to this meeting, he's not a member, but that's one of the things I'm playing with at the moment. I'm using the MPU6050 and PID libraries to manage the feedback between the accelerometer and the speed controllers in an attempt to get a stable hover mode, and the NRF24L01 as the radio module.<br /> <br /> --[[User:Tomoinn|tmo]] 15:12, 2 August 2013 (BST)<br /> <br /> === Bottle rocket telemetry ===<br /> <br /> The family makers are making bottle rockets, I thought it'd be cool to try to make a telemetry module that would tell them how high they'd gone and render a 3d trace of the trajectory using either Processing or WebGL. The main challenge here is to get the circuitry small enough and tough enough to be carried by the rockets and then survive the return to ground level! The second issue is power, I have a LiPo battery and charger so should just be a case of a 3.3v regulator but maybe it needs a boost converter, not really my area of expertise so I'd really like some help there.<br /> <br /> At the moment I'm interested in using an ATTiny85 (8 pin dip package MCU) as an Arduino, using the MPU6050 gyro / accelerometer and an XBee v2 radio - I'd use the NRF24 radio but I think it needs more pins than I have available on the ATTiny. Another option would be to use a rather more sophisticated Arduino pro mini, more pins means the NRF radio would be an option which is much cheaper than the XBee modules.<br /> <br /> --[[User:Tomoinn|tmo]] 15:12, 2 August 2013 (BST)<br /> <br /> === I2C plant moisture sensors ===<br /> <br /> Program an ATTiny85 as an I2C slave, embedding it onto a circuit board etched to work as a capacitive moisture sensor. Use Arduino nano with ethernet shield as an I2C master to then monitor the moisture levels in my various outdoor plant pots and tweet when they're getting too dry.<br /> <br /> --[[User:Tomoinn|tmo]] 15:12, 2 August 2013 (BST)<br /> <br /> === Breadboard prototype of a 1D Pong Game ===<br /> <br /> The idea is to prototype a simple 1D pong game (see [http://www.youtube.com/watch?v=kgQg1DVY4Xc YouTube]) on Arduino or other microcontroller.<br /> <br /> Features:<br /> *Some kind of startup animation (similar to the YouTube video)<br /> *A scoreboard or something similar. Based maybe on a segmented display or LCD.<br /> *SOUNDS! :-)<br /> *Perhaps some different game modes, maybe &quot;powerups&quot; of some kind?<br /> <br /> Eventually I would like this to be the start of a '''MUCH''' larger version of the game (but that's for the future ;-))<br /> <br /> --[[User:DannyG|DannyG]] 15:12, 2 August 2013 (BST)<br /> <br /> === Self-levelling camera gimbal ===<br /> <br /> One popular use of quadcopters is aerial photography/videography, but for this you ideally need a stabilised camera mounting. It's relatively easy to fabricate a two-axis gimbal for a small camera like a GoPro, driven by servos, which can hold itself level using readings from a gyro/accelerometer board.<br /> <br /> [[User:Martin de S|Martin de S]] 12:25, 13 August 2013 (BST)<br /> <br /> === Barn door sky tracker ===<br /> * Goal: take long exposure photos of the sky.<br /> * Problem: the sky rotates over the course of a long exposure.<br /> * Solution: make a motorised mount which rotates your camera at the same rate.<br /> <br /> I'm aiming to build a simple &quot;barn door&quot; mount (http://en.wikipedia.org/wiki/Barn_door_tracker) to enable me to take long exposure sky photos. At its simplest this is two hinged pieces of wood connected by a threaded rod which you turn slowly to increase the angle at the hinge. I'd like to drive this with a stepper motor so it can be left running, and ideally let the Arduino do some of the maths to compensate for the changing geometry of the mount.<br /> <br /> [[User:Martin de S|Martin de S]] 12:25, 13 August 2013 (BST)<br /> <br /> === Electricity monitor and TRIAC based resistive load driver ===<br /> <br /> I need to modulate a large resistive heating load on AC with a TRIAC: whole cycle and half cycle burst fire with some supervisory decision making process to make it comply with the EMC directives. I also need to monitor the power delivered by integrating current and voltage over the waveform and integrating the lot. It would be useful to estimate the supply impedance and/or internal resistance of the load using the same hardware. A lot of this is similar to work done on the Open Energy Monitor by the Solar-PV folks trying to game the tax system - with added EMC directives...<br /> <br /> [http://openenergymonitor.org/emon/]<br /> [http://openenergymonitor.org/emon/node/841]<br /> <br /> [[User:markocosic|markocosic]] 17:37, 21 August 2013 (BST)<br /> <br /> == Custom Arduino IDE Build ==<br /> <br /> I'm working on a custom version of the Arduino IDE to, amongst other things, allow us to cut and paste code from the IDE directly into this wiki. I've made that particular change on my own clone of the code, the adventurous can check it out from https://github.com/tomoinn/Arduino/tree/ide-1.5.x; you'll need to do the following (only tested on linux thus far!)<br /> <br /> &lt;span style='font-family:monospace; display: block; margin-left: 20px;'&gt;<br /> &gt; git clone git@github.com:tomoinn/Arduino.git&lt;br&gt;<br /> &gt; git checkout ide-1.5.x&lt;br&gt;<br /> &gt; cd Arduino/build&lt;br&gt;<br /> &gt; ant run<br /> &lt;/span&gt;<br /> <br /> You should then have a version of the IDE based on version 1.5 but with an extra context menu option 'copy as MediaWiki HTML', if you use this and then copy the clipboard into an editor in our wiki you should get something like the following:<br /> <br /> &lt;span style='font-family: monospace; display: block; margin-left: 10px; margin-right: 10px; margin-top: 10px; margin-bottom: 10px; padding: 6px; border: 1px solid #aaa; font-size: 12px; line-height: 15px;background-color: #f9f9f9;'&gt;&lt;span style='color: #7E7E7E;'&gt;/*&lt;/span&gt;&lt;br&gt;<br /> &lt;span style='color: #7E7E7E;'&gt;&amp;nbsp;&amp;nbsp;Blink&lt;/span&gt;&lt;br&gt;<br /> &lt;span style='color: #7E7E7E;'&gt;&amp;nbsp;Turns&amp;nbsp;on&amp;nbsp;an&amp;nbsp;LED&amp;nbsp;on&amp;nbsp;for&amp;nbsp;one&amp;nbsp;second,&amp;nbsp;then&amp;nbsp;off&amp;nbsp;for&amp;nbsp;one&amp;nbsp;second,&amp;nbsp;repeatedly.&lt;/span&gt;&lt;br&gt;<br /> &lt;span style='color: #7E7E7E;'&gt;&amp;nbsp;&lt;/span&gt;&lt;br&gt;<br /> &lt;span style='color: #7E7E7E;'&gt;&amp;nbsp;This&amp;nbsp;example&amp;nbsp;code&amp;nbsp;is&amp;nbsp;in&amp;nbsp;the&amp;nbsp;public&amp;nbsp;domain.&lt;/span&gt;&lt;br&gt;<br /> &lt;span style='color: #7E7E7E;'&gt;&amp;nbsp;*/&lt;/span&gt;&lt;br&gt;<br /> &lt;br&gt;<br /> &lt;span style='color: #7E7E7E;'&gt;//&amp;nbsp;Pin&amp;nbsp;13&amp;nbsp;has&amp;nbsp;an&amp;nbsp;LED&amp;nbsp;connected&amp;nbsp;on&amp;nbsp;most&amp;nbsp;Arduino&amp;nbsp;boards.&lt;/span&gt;&lt;br&gt;<br /> &lt;span style='color: #7E7E7E;'&gt;//&amp;nbsp;give&amp;nbsp;it&amp;nbsp;a&amp;nbsp;name:&lt;/span&gt;&lt;br&gt;<br /> &lt;span style='color: #CC6600;'&gt;int&lt;/span&gt; led = 13;&lt;br&gt;<br /> &lt;br&gt;<br /> &lt;span style='color: #7E7E7E;'&gt;//&amp;nbsp;the&amp;nbsp;setup&amp;nbsp;routine&amp;nbsp;runs&amp;nbsp;once&amp;nbsp;when&amp;nbsp;you&amp;nbsp;press&amp;nbsp;reset:&lt;/span&gt;&lt;br&gt;<br /> &lt;span style='color: #CC6600;'&gt;void&lt;/span&gt; &lt;span style='color: #CC6600;'&gt;&lt;b&gt;setup&lt;/b&gt;&lt;/span&gt;() { &lt;br&gt;<br /> &amp;nbsp;&amp;nbsp;&lt;span style='color: #7E7E7E;'&gt;// initialize the digital pin as an output.&lt;/span&gt;&lt;br&gt;<br /> &amp;nbsp;&amp;nbsp;&lt;span style='color: #CC6600;'&gt;pinMode&lt;/span&gt;(led, &lt;span style='color: #006699;'&gt;OUTPUT&lt;/span&gt;); &lt;br&gt;<br /> }&lt;br&gt;<br /> &lt;br&gt;<br /> &lt;span style='color: #7E7E7E;'&gt;//&amp;nbsp;the&amp;nbsp;loop&amp;nbsp;routine&amp;nbsp;runs&amp;nbsp;over&amp;nbsp;and&amp;nbsp;over&amp;nbsp;again&amp;nbsp;forever:&lt;/span&gt;&lt;br&gt;<br /> &lt;span style='color: #CC6600;'&gt;void&lt;/span&gt; &lt;span style='color: #CC6600;'&gt;&lt;b&gt;loop&lt;/b&gt;&lt;/span&gt;() {&lt;br&gt;<br /> &amp;nbsp;&amp;nbsp;&lt;span style='color: #CC6600;'&gt;digitalWrite&lt;/span&gt;(led, &lt;span style='color: #006699;'&gt;HIGH&lt;/span&gt;); &lt;span style='color: #7E7E7E;'&gt;// turn the LED on (HIGH is the voltage level)&lt;/span&gt;&lt;br&gt;<br /> &amp;nbsp;&amp;nbsp;&lt;span style='color: #CC6600;'&gt;delay&lt;/span&gt;(1000); &lt;span style='color: #7E7E7E;'&gt;// wait for a second&lt;/span&gt;&lt;br&gt;<br /> &amp;nbsp;&amp;nbsp;&lt;span style='color: #CC6600;'&gt;digitalWrite&lt;/span&gt;(led, &lt;span style='color: #006699;'&gt;LOW&lt;/span&gt;); &lt;span style='color: #7E7E7E;'&gt;// turn the LED off by making the voltage LOW&lt;/span&gt;&lt;br&gt;<br /> &amp;nbsp;&amp;nbsp;&lt;span style='color: #CC6600;'&gt;delay&lt;/span&gt;(1000); &lt;span style='color: #7E7E7E;'&gt;// wait for a second&lt;/span&gt;&lt;br&gt;<br /> }&lt;br&gt;<br /> &lt;/span&gt;<br /> <br /> Should make putting example code up easier - I'm also thinking of customizing colours, logo etc to create a makespace edition of the IDE. As and when it becomes a bit more stable I'll start doing proper builds for linux and windows at least. Note that cloning the github repository takes a long time, it's going on for 600Mb of data, potentially you can cut that down by only cloning the ide-1.5.x branch if you're familiar with git.<br /> <br /> --[[User:Tomoinn|tmo]] 14:09, 13 September 2013 (BST)</div>

JCGS http://wiki.makespace.org/Equipment/Laser_Cutter 2016-12-12T14:19:00Z

<p>JCGS: Improve earlier edit</p> <hr /> <div><br /> {{RedTool}}<br /> <br /> [[Equipment|Equipment]] / Laser Cutter<br /> <br /> [[File:Makespace-laser-cutter.JPG|thumb|460px|right|Our LS6090 PRO Laser Cutter]]<br /> <br /> = Summary =<br /> <br /> We have two LS 6090 PRO Laser Cutters. Each has a working area of 900mm by 600mm, and is powered by a 60w CO2 Water Cooled Laser Tube that can engrave and cut through materials such as wood, plastic, card, leather, fabrics, up to about 10-15mm thick (note, it can not cut metal). The laser cut is approximately 0.15mm wide, and a job can take a few seconds through to tens of minutes depending on material thickness and design complexity. <br /> <br /> We have dedicated PCs running LaserCut 5.3 software to import, prepare and download jobs to the Laser Cutter. It can import various formats, with DXF being the most commonly used, so various software packages can be used to create your designs.<br /> <br /> Here are some examples of laser jobs we've run (please add a photo of yours any time you do a job!)<br /> <br /> &lt;gallery&gt;<br /> File:Laser-cut-focus-tool.JPG<br /> File:Laser-cut-front-panels.JPG<br /> File:Laser-cut-lizards.JPG<br /> File:Laser-cut-m-and-s.JPG<br /> File:Laser-cut-model-building.JPG<br /> File:Laser-cut-ply-m.JPG<br /> File:Laser_output_-_makespace_arrow.JPG<br /> File:Laser_box.jpg<br /> File:Croc-small.jpg<br /> File:LaserCutter_Jobs_1.jpg<br /> File:LaserCutterGallery_20130328.jpg<br /> File:LasercutSettlers.jpg<br /> File:Wolfstock1.jpg<br /> File:Mug-holder.jpg<br /> File:2013-10-21 20.10.06.jpg<br /> File:Indy jigster.png<br /> &lt;/gallery&gt;<br /> <br /> = Using the Laser Cutter =<br /> <br /> The laser cutter is a great way to easily produce accurate and complex 2D forms in various materials, and can be designed for with limited experience in various drawing or CAD applications. At the same time, it is an expensive tool with real risk of injury and fire, so is very important you know how to use it to avoid damaging yourself and the machine. '''You must only use the laser cutter if you have been trained, and if you are ever in any doubt about something, please ask for assistance.'''<br /> <br /> == Owners ==<br /> <br /> The Owners are those who have volunteered to be in charge of the laser cutter, organising maintenance, responding to technical issues and generally being a point of contact. The current Owners of the Laser Cutter are:<br /> <br /> * [[User:Mat-C|Mat Cook]]<br /> * [[User:DianaProbst|Diana Probst]]<br /> * Owners who are a little less current, but may still be able to help:<br /> ** [[User:Simon|Simon Ford]]<br /> ** [[User:Barhamd|David Barham]]<br /> ** [[User:Nickcadsoftuk|Nick Johnson]]<br /> <br /> == Trainers ==<br /> <br /> The Trainers are those who have volunteered to teach others to use the laser cutter and to promote good working practice. The current Trainers for the Laser Cutter are:<br /> <br /> * Brian Starkey<br /> * [[User:stevancw|Stevan Wing]]<br /> * [[User:Mat-C|Mat Cook]]<br /> * [[User:robv|Rob Voisey]]<br /> <br /> * Currently slightly less frequent trainers are:<br /> ** Martin de Selincourt<br /> ** [[User:Simon|Simon Ford]]<br /> ** [[User:Barhamd|David Barham]]<br /> ** [[User:Nickcadsoftuk|Nick Johnson]]<br /> ** [[User:Tmonca|Toby Moncaster]]<br /> <br /> <br /> If you have any questions, problems or concerns around the laser cutter, please use the forum page:<br /> * [http://makespace.org/forum/viewtopic.php?f=19&amp;t=45 Laser Cutter Log]<br /> <br /> For the old mailing list thread see here:<br /> * [https://groups.google.com/d/topic/cammakespace/Tmce2iKVzD8/discussion Log : Laser Cutter]<br /> <br /> == Training ==<br /> <br /> &lt;div style=&quot;background:#FADADD; border:1px solid #FFC0CB; padding:5px&quot;&gt;<br /> &lt;b&gt;YOU CAN ONLY USE THE LASER CUTTER IF YOU HAVE BEEN TRAINED&lt;/b&gt;&lt;br&gt;<br /> and have been added to the [[Equipment/Laser_Cutter/Training#Trained_Users|Trained Users]] list by one of the Owners<br /> &lt;/div&gt;<br /> <br /> To get trained on the laser cutter and be added to the qualified user list, you will need to arrange for a training session with one of the Laser Cutter Owners. <br /> <br /> If you'd like to arrange training, please see:<br /> * [[Equipment/Laser_Cutter/Training|Laser Cutter Training]]<br /> <br /> == Health and Safety ==<br /> <br /> The laser cutter is a potentially dangerous piece of equipment which must only be operated by members who have received appropriate training and who take due care. The top things to always remember when using the laser cutter are:<br /> * '''ONLY USE THE LASER CUTTER IF YOU ARE ON THE LIST OF TRAINED USERS'''<br /> * '''NEVER LEAVE THE LASER CUTTER RUNNING UNATTENDED'''<br /> * '''KNOW WHAT TO DO IF A FIRE BREAKS OUT'''<br /> * '''NEVER CUT MATERIALS THAT YOU DON'T KNOW ARE SAFE'''<br /> <br /> As a trained user, you should be very aware of the following risks and how to deal with them:<br /> <br /> '''FIRE (under normal operation)''' - Cutting at the wrong speed or the wrong power can result in the material igniting<br /> * You must watch the cutter at all times and be prepared to abort the job if problems occur<br /> * Small flashes of flame that don't hang around for a fraction of a second are acceptable, but any more is rare and not acceptable<br /> * If a fire does take, this is the process you should follow (from minor to major):<br /> ** Press &quot;pause&quot; (the same button you started the job with) - This will turn the laser off so no more heat enters, and assuming the flame goes out, you can press &quot;start&quot; for the job to continue where it left off<br /> ** Open the lid - With the job paused, you can open the lid to blow out the flame. Again, it is possible to re-close the lid and continue where you left off<br /> ** Move the material from under the laser head assuming safe to do so (so it doesn't damage the optics; alternatively send the laser to home/datum), and smother with a spare sheet of material or blow out<br /> ** Use the workshop CO2 extinguisher to extinguish the flame<br /> * You should also make a note in the log if any of this happens with associated materials and settings so we can keep track of any particular materials/settings we should look at <br /> <br /> '''FIRE (abnormal operation)''' - If the head gets stuck or something else goes wrong, ignition could happen much more suddenly or intensely<br /> * You must watch the cutter at all times and be prepared to abort the job if problems occur<br /> * If the head gets trapped (e.g. tomb-stoning of a piece, mechanical failure) or any other problem occurs that causes or could cause fire, this is the process you should follow:<br /> ** Hit the emergency stop<br /> ** Open the lid and move the material from under the laser head assuming safe to do so (so it doesn't damage the optics)<br /> ** Blow out, smother with a spare sheet of material, or use the CO2 extinguisher to extinguish the flame as appropriate<br /> * Ensure a Maintainer looks at the machine before it is brought back in to action if it is not obvious what went wrong and all is ok<br /> * You should also make a note in the log if any of this happens with associated materials and settings so we can keep track of any particular materials/settings we should look at <br /> <br /> '''FUMES''' - The laser cutting process will release different smoke and fumes depending on the material.<br /> * Never cut PVC or a material you are not sure is safe. When PVC is heated it releases chlorine gas, this mixes with the moisture in the air and the result is hydrochloric acid which is toxic to humans and corrosive to machines. <br /> * Ensure the filter is on and the cutter lid stays closed for a while after a job to allow the fumes to clear. <br /> * If you are feeling strange, think the fume build up is too much, or for any other reason you are unsure, stop the job.<br /> <br /> '''TRAPPING''' - The head and bed of the cutter can be moved by the front panel menu or programs in the machines memory. <br /> * Be careful when working inside the cutting area or with the lid open not to trap hands, hair, clothing or anything else. <br /> * Always check the machine for unexpected items that may have fallen in before closing the lid. <br /> * Do not attempt to climb into the machine!<br /> <br /> '''LASER BURNS/LIGHT''' - A 60W laser can do real damage. <br /> * The laser should be safe within the confines of the machine, and cut-off automatically when the lid is open (although this should not be relied upon). The top window is safe to look through during a job, but do not attempt to interfere with these windows or the laser or in any way invent some way to look at the laser.<br /> * Do not tamper with the laser cutter, or any interlocks. All side panels of the laser should always be closed and locked whilst the machine is plugged in. <br /> * Do not put metal in the laser cutter.<br /> <br /> == Can I cut it? ==<br /> <br /> If it's not on this list, the answer is &quot;NO YOU CAN'T CUT IT AT MAKESPACE&quot;. Even if other people say it's ok. Bear in mind that we can't ventilate externally like other people can.<br /> <br /> If it's something that isn't covered here, do ask on the forums and we'll look into it :)<br /> <br /> *Woody things<br /> ** Wood: yes! (be careful of fire)<br /> ** Plywood: yes if it is &quot;laser ply&quot;. Normal plywood has non-laser compatible glue<br /> ** MDF: no. Clogs up our filters and smells bad.<br /> ** LaserMDF: no. It produces perhaps 50% the gunk of MDF but still too much.<br /> ** Cork: yes, but it with a badly charred edge, and won't cut very deeply --- try cutting from the back of your sheet and using the cut to guide a craft knife / scalpel to make a neat cut through to the front.<br /> <br /> *Plasticy things<br /> ** Acrylic / Perspex: yes!<br /> ** PVC/Vinyl: absolutely not. Produces chlorine.<br /> ** Silicone: we tried it with very limited success. A mm or two perhaps, anything else chars and doesn't cut.<br /> ** White Delrin/Acetal: yes with great care. Make sure filters running well. Don't open lid too quickly. Check for fumes and fire.<br /> ** Black Delrin/Acetal: no. contains carbon black which can be toxic.<br /> ** Teflon: no (it is toxic)<br /> ** Nylon: no (consult an owner)<br /> ** Polythene/polyethylene: no (consult an owner)<br /> ** Lexan/Polycarbonate: no (consult an owner)<br /> ** Polypropylene: yes just. You must clean the bed. It will cut up to about 2mm. It's not a great quality cut, but just about doable. Fire risk.<br /> ** GPPS / Polystyrene / HIPS in thin solid sheet form: maybe. ask owner to help. NO FOAM (it's highly flammable)<br /> <br /> *Papery things<br /> ** Card/Paper: yes! (be careful of fire)<br /> ** Tissue: yes if super super really careful (be REALLY careful of fire, have emergency procedure in place before you start)<br /> <br /> *Metally things<br /> ** Metal of any thickness doesn't cut. The surface can be engraved with a paint application. LMM6000 Surmark/Thermark has been tested and is suggested for use, but expensive. The owners suggest a speed of 800 and maximum power.<br /> <br /> *Exotics<br /> ** Fibre glass: no (unknown resin, glass particles)<br /> ** Carbon Fibre: no<br /> ** Slate: engravable for good effect<br /> <br /> Good list of info here: http://inventionstudio.gatech.edu/wiki/Laser_cutter (page disappeared, some time before 2016-12-12)<br /> <br /> == Instructions ==<br /> <br /> To use the laser cutter, you must have been trained and have had your name added to the trained user list; these instructions are not a substitute for this training. See the training section to understand how you can become qualified to use the laser cutter.<br /> <br /> Although not a requirement, it is recommended someone else trained is also present when using the laser cutter. Having two pairs of eyes helps avoid forgotten steps, allows for double checking, clarifications and discussions, and ensures a greater pool of experience is both present and being built up as the laser is used.<br /> <br /> '''Power Up'''<br /> <br /> Give the machine a quick visual check. Make sure that there is nothing left on the bed, the water reservoir of the chiller looks normal, and that the equipment has no obvious damage or signs of being out-of-action. If the bed looks like it has residue on it, give it a wipe with IPA and a cloth. <br /> <br /> Turn on primary switch on the trunking marked 'Laser'. The air filter system to the right of the laser cutter should start as should the air pump and the chiller. It should power up, make a decent amount of noise, and the lights should indicate the filter is in good condition (i.e. no need for replacement).<br /> <br /> Make sure the lid is closed. Turn on the laser using the key on the right hand side. The inspection lamp should come on, a satisfying hum start up, and the cutter go into doing its self-checks.<br /> <br /> Before doing any job, the laser should be left to warm up for 4-5 mins. While the machine warms up, power on the adjacent PC and start the LaserCut application from the desktop. During this time the water temperature shown on the chiller should drop from ambient temperature to the usual setting of 18C.<br /> <br /> '''Load your Design'''<br /> <br /> The PC software has an import facility ('''file &gt; import''') which seems to be happy taking AutoCAD 2004 DXF files and other formats. The workspace of the laser bed is represented as the workarea in the LaserCut software. If the import doesn't do what you want size-wise, you can select the whole image and then use the 'size' command from the drop down menu to set the dimension you want. Clicking on the three dots ... symbol will adjust the other axis in the same proportion (keeping the aspect ratio fixed). Selecting the 'centre on bed' option will locate your imported drawing on the centre of the machine's cutting bed.<br /> <br /> '''Assign Settings to Colours'''<br /> <br /> Each part of your drawing that is assigned a different colour can have a different cut action assigned. Each colour will appear on the menu on the right hand side of the screen with numbers related to power and speed of the laser which will be used for the colour. <br /> <br /> The main options are to Cut (line) or Engrave (raster fill). A marking on the material is a Cut. For each material and cutting depth required, a corresponding speed and power must be entered. The handbook provided with the machine gives suggested values for various materials but these should be considered as a starting point for a test. See the '''Power and Speed Settings''' section for our guidelines and experiences for these settings.<br /> <br /> '''Download to the Cutter'''<br /> <br /> Your drawing will feature a blue dot which represents the starting point of the laser; this is by default on the top right corner. In general, you will want to use &quot;immediate&quot; mode, which means this point represents wherever the laser is positioned when you start the job. You can also run the job in absolute mode by unchecking the box, making the job use absolute positioning on the workspace. <br /> <br /> To download, select Download and Download Current; the download option will by default call the file on the laser cutter 'LASER'.<br /> <br /> '''Set the Focus'''<br /> <br /> Before each job, the focus needs to be checked and set by adjusting the height of the bed, and thus the work piece, from the lens. The critical dimension here is 41mm and several gauges made of perspex will be left around the machine. This gauge needs to be a fit between the top surface of the material you intend to cut and the white plastic 'flap' on the lens piece. The height of the table is adjusted using the UP and DOWN buttons. Failure to set the distance correctly will result in an out of focus laser and much bigger (but lower powered) cut line. Always ensure there is clearance between the material and laser head before the head moves. <br /> <br /> '''Aligning and Testing the Job'''<br /> <br /> The cutter's menu will show the most recent downloaded file highlighted. Pressing the 'test' button will make the head travel along the square maximum extends of the cuts. This shows you that you have the material in the right place, and you have enough of it! You can do this repeatedly, moving the work piece by hand or the laser head using the arrow keys (after hitting ESC), until you are confident you have things where you want them.<br /> <br /> '''Cut the Job'''<br /> <br /> When happy with the location of the material, close the lid and press 'start' to start the cutter. Watch the head and at least at first be prepared to press the 'stop' button immediately if you find you are burning massive holes in your work piece! This goes back to doing some tests on a sample of your material and making sure you are happy with the cut speeds and power you have selected. You should stay near the cutter at all times and be prepared to pause it or stop it in the event of fire. <br /> <br /> &lt;span style=&quot;color:red&quot;&gt;'''DO NOT EVER LEAVE THE CUTTER UNATTENDED'''&lt;/span&gt;<br /> <br /> '''Finishing'''<br /> <br /> The end of the job is signified by a beep. Waiting a few moments for the exhaust pump to clear any remaining smoke is a good idea, especially with wood, and will limit the build up of smells in the rest of the workshop. Remove your work piece, ensuring that all parts are cleared from the bed of the machine.<br /> <br /> '''Power Down'''<br /> <br /> The cutter is turned off using the key switch, then the air filtering system with the green rocker switch. Shut down the PC and double check that everything is left in a safe state for the next user. <br /> <br /> '''Clean the bed of debris using the soft brush, then wipe down the bed using IPA and a cloth.'''<br /> <br /> If you have been cutting particularly 'dirty' materials, most notable MDF and Ply which leave a sticky residue then you will need to use the course side of one of the oven pads and lots of 'elbow grease'. Residue on the bed can impact the next persons' job so please make the effort to clean up and leave the cutter as you would wish to find it.<br /> <br /> Go away excited by what you can make and come back with lots more drawings!<br /> <br /> == Power and Speed Settings ==<br /> <br /> In due time we will try to build up a large sample stock of materials and record the values which work best. Here are the sample material tests we have so far:<br /> <br /> &lt;gallery&gt;<br /> File:Laser-schmoo-3mm-acrylic.JPG|3mm Acrylic<br /> File:Laser-schmoo-10mm-acrylic.JPG|10mm Acrylic<br /> File:Laser-schmoo-9mm-mdf.JPG|9mm MDF (note: do not cut MDF - see above!)<br /> &lt;/gallery&gt;<br /> <br /> Settings to get you started:<br /> *3mm Acrylic: Speed 12, Power 100, Corner power 100<br /> *5mm Acrylic: Speed 6, Power 100, Corner power 100<br /> *Acrylic shallow cut: Speed 30, power 50, corner power 50<br /> *Etching acrylic: Speed 400, Power 50, Spacing 0.05<br /> <br /> To make your own material test, a test grid can be downloaded here: [[Media:Test grid.zip]]<br /> <br /> == Tips &amp; Tricks ==<br /> <br /> * If the laser cutter's user interface does not seem to respond/do what you want, hit &quot;ESC&quot; to return to 'normal mode'.<br /> * The opaque white acrylic needs slightly stronger settings for surface cuts as they are not as visible as in the transparent acrylic (i.e., for similar effect you need a deeper cut). Otherwise seems to cut equivalently to transparent acrylics.<br /> * If you want a tight fit of pieces or very accurate sizing, keep in mind that the laser beam has a width of just over 0.1 mm (maybe 0.11 or 0.12 mm). So all exterior cut lines should be offset by 0.05 mm; you can do this very easily in the LaserCutter Software with the &quot;Offset&quot; tool (units are in mm, so enter '0.05' and select 'Outer').<br /> * The DXF file format stores values only (not values and units). The internal units in the LaserCutter are in mm. If you set your document's units to mm in the exporting CAD system it should work fine, but generally it is a good idea to have a piece of geometry of known length, e.g. a line 100mm long, or a box of known size around your design. This makes adjusting the scaling a lot easier.<br /> * If you want to export a DXF from Inkscape (which is a great, free vector drawing package), then make sure you do &quot;Object to path&quot; from the Path menu for the whole object and then during the export stage, untick both options for type of export. Choose mm as your unit.<br /> * There's now a page to help with Inkscape and our laser at [[Equipment/Laser_Cutter_Inkscape]]<br /> * If the jog buttons (arrow keys moving the laser head around) are only moving the head in small single steps rather than moving it continuously, make sure that the jog step size is set to 0.0mm in the Jog Settings section of the menu.<br /> <br /> === Material Usage ===<br /> You want to use as little material as possible to save money, we want you to use as little material as possible to reduce re-stocking burden and wastage.<br /> There's a neat tool you can use for packing SVG files into small spaces, find it here: http://svgnest.com/<br /> <br /> == Fixing up a job that went wrong ==<br /> <br /> If you messed up a job and, for example, some cut lines weren't cut, you might try to run the job again after recolouring all of the lines except the ones that didn't cut. You can then deselect those lines for output in the Cut/Engrave window on the top right of the Lasercut Interface, and this will keep your positioning.<br /> <br /> If your head has moved, you can try setting some lines to power 1, which should not cut anything, but allows you to see where the head is travelling.<br /> <br /> == Fixing strange issues ==<br /> <br /> ''Jaws has a FAQ on the desktop of her PC, with more useful hints, tricks, and solutions.''<br /> <br /> * Etching doesn't work<br /> ** Lines are not closed. LaserCut usually warns you about this. Ctrl-a to select all, then Tools-&gt;Unite Lines (0.001 should be fine).<br /> ** Two copies on top of each other. Copies on top of each other &quot;cancel out&quot; any etching. Delete one copy.<br /> ** Test with Menu-&gt;Laser-&gt;Simulate<br /> <br /> * LaserCut will not download to the laser cutter<br /> ** Check laser cutter isn't in a paused state<br /> ** Restart LaserCut on the PC. (We've not had any usb issues nor needed to restart the laser since upgrading the PC summer 2014).<br /> <br /> * Laser cuts things out 2+ times<br /> ** Check you don't have two copies loaded on top of each other<br /> ** Check it's not set to cut multiple times in LaserCut (this setting is right of the Cut/Engrave/Speed/Power settings)<br /> ** Check the laser front panel says &quot;001&quot; at the bottom. If not, press right arrow until the number is highlighted, then down to adjust back to 1, then press return.<br /> <br /> * Laser will only cut at the top right of the bed<br /> ** Download again with Immediate Mode ticked<br /> ** On laser panel, press return (I think?) then right twice (should select the bottom left option), then press return (I think).<br /> <br /> *You Hit Emergency stop<br /> ** E-M button needs twisting to re-activate<br /> ** If that fails - check the circuit breaker inside. From the back of the machine, you want to open the lower flap on the left side, which should be unlocked. Near to the back, there is a breaker board. Flip the flippy bit.<br /> <br /> == Material Stock ==<br /> For the stock we hold, please see the [[Equipment/Laser_Cutter_Stock|Laser cutter stock]] page.<br /> <br /> = Maintenance =<br /> <br /> The maintenance of the Laser Cutter is carried out by the Owners, with some basic maintenance being carried out by Users on every job.<br /> <br /> == Maintenance Schedule ==<br /> <br /> Continuous Maintenance ('''Every job, done by all Laser Cutter Users''')<br /> * Clean the laser bed with IPA and cloth or Swarfega wipes<br /> * Clean any debris off laser bed and surround using soft brush<br /> <br /> Basic Maintenance (Every week, done by Laser Cutter Maintainers)<br /> * Clean the laser lens with IPA and cotton buds<br /> * Oil the 3 runners with 3-in-one light oil <br /> * Thoroughly clean the laser bed with IPA and cloth<br /> * Check the water level in the cooling tank<br /> * Clean and remove debris from the machine base and catchment drawer<br /> <br /> Full Maintenance (Every 4 weeks, done by Laser Cutter Maintainers)<br /> * Check the water is clean in the cooling tank (i.e. no contamination/organic build up)<br /> * Check filter unit for filter renewal<br /> * Oil the 4 rise and fall lead screws with 3-in-one light oil<br /> * Check mirrors and clean with a disposable sachet lens cleaner cloth (only if needed, mirror coatings are delicate)<br /> * Work through mirror alignment procedure to check alignment of mirrors<br /> <br /> == Maintenance Log ==<br /> <br /> ''For full log, see laser cutter wall sheet''<br /> <br /> '''Filter Changes'''<br /> * Jaws: 10 Feb to 22 June 2016, slightly under 5 months, and falling<br /> * Betsy: Freshest data currently in filter unit, gave up on 24th of June<br /> <br /> <br /> '''Reactive Maintenance'''<br /> * 15th Jan 2013, Simon Ford: Laser cutter not powering up, with switching on via key gives no activity whatsoever. No recollection of it cutting out during a job (Alexis), so assume it just stopped turning on at some point. Filter box and power sockets confirmed OK. Diagnosis: RCD in right back panel of Laser reset to off, no obvious reason why. Switching back on brought everything back to life OK.<br /> * 22nd, Simon Ford; 29th, Nicholas - same again.<br /> <br /> * Apr 2014, Mat Cook and Diana Probst: after previous changing of chiller water (Roger et al) the pump was complaining of lack of flow. Changed water and filtered, removed small blockage from rubber hose on laser tube.<br /> <br /> * 16 Apr 2014, Toby and Diana: changed laser tube, refilled chiller. Laser cutter fully working.<br /> <br /> * 25 Oct 2014, Mat and Diana mended lid spring brace. Cutter working fully.<br /> <br /> '''Regular Maintenance'''<br /> * Week Number, Date, Type, Owner (Notes)<br /> <br /> 2013<br /> * January 7, Full, Chris @ HPCLaser'''<br /> * January 14, Basic, Simon Ford <br /> * January 21, Full, Simon Ford (running better than new :)'''<br /> * ...various maintenance events happened...<br /> * April 5th, Full, Simon Ford<br /> * July 1st, Full, David Barham (realigned mirrors)<br /> * July 15th, installed chiller<br /> <br /> 2014<br /> * 16 Apr 2014, mirror alignment and optics checked after re-installation of tube. All fine. Toby and Diana.<br /> * 19 May 2014, mirrors cleaned, earthing wire on lid tightened. Diana (and Mat's screwdriver)<br /> * 21 May 2014, cleaned lens with Mat Cook. Diana<br /> * 02 Jun 2014, removed and cleaned laser bed<br /> * 14 Sep 2014, cleaned lens and mirrors, realigned. Diana and Brian Starkey<br /> <br /> * 30 Jun 2014 Fitted microswitches in series with the magnetic &quot;lid closed&quot; detector. <br /> * ??? 2014 &quot;Jaws&quot; Second laser cutter acquired<br /> * ??? 2014 Fitted microswitch to Jaws<br /> <br /> == Maintenance Shopping List ==<br /> <br /> * 3-in-one light oil <br /> * Cotton Buds<br /> * Lens cleaner sachets<br /> * Soft paint/cleaning brush<br /> * Thermometer for water tank<br /> * Hand held CO2 extinguisher<br /> <br /> = Further Information =<br /> <br /> * [http://hpclaser.co.uk/index.php?main_page=product_info&amp;cPath=1&amp;products_id=11 LS 6090 PRO Laser Product Page]<br /> * [http://hpclaser.co.uk/index.php?main_page=page&amp;id=5&amp;chapter=2 HPCLaser Technical Info]<br /> * [http://www.laserscript.co.uk/phpBB3/ Laserscript Forum]<br /> <br /> LaserCut 5.3<br /> * [http://www.leetro.com/english/sale/35.html Homepage]<br /> * [http://www.leetro.com/english/down/LaserCut5.3%20Manual%20V1.6.pdf Manual]<br /> <br /> == Installation ==<br /> <br /> &lt;gallery&gt;<br /> File:Laser_-_van.JPG<br /> File:Makespace-laser-install-02.JPG<br /> File:Laser_-_building_2.JPG<br /> File:Laser_-_building.JPG<br /> &lt;/gallery&gt;<br /> <br /> == Purchase ==<br /> <br /> Full Purchase, Delivery and Installation (£6865.00+vat = £8238.00)<br /> * [http://hpclaser.co.uk/index.php?main_page=product_info&amp;cPath=1&amp;products_id=11 LS 6090 PRO Laser engraving and cutting machine, 600mm by 900mm 60W] (£5250.00+vat)<br /> * [http://hpclaser.co.uk/index.php?main_page=product_info&amp;cPath=2&amp;products_id=34 Laser Fume Filter] (£1250.00+vat)<br /> * Delivery (£190+vat)<br /> * Installation/Training (£175+vat)<br /> <br /> == Repairs ==<br /> <br /> We expect to have to change the following parts for general maintenance:<br /> * The laser tube (guess every 6-12 months)<br /> * The filter (guess every 3-6 months)<br /> * The optics (guess every 6-12 months)<br /> <br /> Maintenance and Spares:<br /> * [http://hpclaser.co.uk/index.php?main_page=product_info&amp;cPath=2&amp;products_id=3 60 watt C02 laser tube] (£275.00+vat)<br /> * [http://hpclaser.co.uk/index.php?main_page=product_info&amp;cPath=2&amp;products_id=12 50 mm Focus Meniscus Lens] (£75.00+vat)<br /> * Estimate for Call Out (£200.00)</div>

JCGS http://wiki.makespace.org/Equipment/Laser_Cutter 2016-12-12T14:13:09Z

<p>JCGS: Remark that a link is stale</p> <hr /> <div><br /> {{RedTool}}<br /> <br /> [[Equipment|Equipment]] / Laser Cutter<br /> <br /> [[File:Makespace-laser-cutter.JPG|thumb|460px|right|Our LS6090 PRO Laser Cutter]]<br /> <br /> = Summary =<br /> <br /> We have two LS 6090 PRO Laser Cutters. Each has a working area of 900mm by 600mm, and is powered by a 60w CO2 Water Cooled Laser Tube that can engrave and cut through materials such as wood, plastic, card, leather, fabrics, up to about 10-15mm thick (note, it can not cut metal). The laser cut is approximately 0.15mm wide, and a job can take a few seconds through to tens of minutes depending on material thickness and design complexity. <br /> <br /> We have dedicated PCs running LaserCut 5.3 software to import, prepare and download jobs to the Laser Cutter. It can import various formats, with DXF being the most commonly used, so various software packages can be used to create your designs.<br /> <br /> Here are some examples of laser jobs we've run (please add a photo of yours any time you do a job!)<br /> <br /> &lt;gallery&gt;<br /> File:Laser-cut-focus-tool.JPG<br /> File:Laser-cut-front-panels.JPG<br /> File:Laser-cut-lizards.JPG<br /> File:Laser-cut-m-and-s.JPG<br /> File:Laser-cut-model-building.JPG<br /> File:Laser-cut-ply-m.JPG<br /> File:Laser_output_-_makespace_arrow.JPG<br /> File:Laser_box.jpg<br /> File:Croc-small.jpg<br /> File:LaserCutter_Jobs_1.jpg<br /> File:LaserCutterGallery_20130328.jpg<br /> File:LasercutSettlers.jpg<br /> File:Wolfstock1.jpg<br /> File:Mug-holder.jpg<br /> File:2013-10-21 20.10.06.jpg<br /> File:Indy jigster.png<br /> &lt;/gallery&gt;<br /> <br /> = Using the Laser Cutter =<br /> <br /> The laser cutter is a great way to easily produce accurate and complex 2D forms in various materials, and can be designed for with limited experience in various drawing or CAD applications. At the same time, it is an expensive tool with real risk of injury and fire, so is very important you know how to use it to avoid damaging yourself and the machine. '''You must only use the laser cutter if you have been trained, and if you are ever in any doubt about something, please ask for assistance.'''<br /> <br /> == Owners ==<br /> <br /> The Owners are those who have volunteered to be in charge of the laser cutter, organising maintenance, responding to technical issues and generally being a point of contact. The current Owners of the Laser Cutter are:<br /> <br /> * [[User:Mat-C|Mat Cook]]<br /> * [[User:DianaProbst|Diana Probst]]<br /> * Owners who are a little less current, but may still be able to help:<br /> ** [[User:Simon|Simon Ford]]<br /> ** [[User:Barhamd|David Barham]]<br /> ** [[User:Nickcadsoftuk|Nick Johnson]]<br /> <br /> == Trainers ==<br /> <br /> The Trainers are those who have volunteered to teach others to use the laser cutter and to promote good working practice. The current Trainers for the Laser Cutter are:<br /> <br /> * Brian Starkey<br /> * [[User:stevancw|Stevan Wing]]<br /> * [[User:Mat-C|Mat Cook]]<br /> * [[User:robv|Rob Voisey]]<br /> <br /> * Currently slightly less frequent trainers are:<br /> ** Martin de Selincourt<br /> ** [[User:Simon|Simon Ford]]<br /> ** [[User:Barhamd|David Barham]]<br /> ** [[User:Nickcadsoftuk|Nick Johnson]]<br /> ** [[User:Tmonca|Toby Moncaster]]<br /> <br /> <br /> If you have any questions, problems or concerns around the laser cutter, please use the forum page:<br /> * [http://makespace.org/forum/viewtopic.php?f=19&amp;t=45 Laser Cutter Log]<br /> <br /> For the old mailing list thread see here:<br /> * [https://groups.google.com/d/topic/cammakespace/Tmce2iKVzD8/discussion Log : Laser Cutter]<br /> <br /> == Training ==<br /> <br /> &lt;div style=&quot;background:#FADADD; border:1px solid #FFC0CB; padding:5px&quot;&gt;<br /> &lt;b&gt;YOU CAN ONLY USE THE LASER CUTTER IF YOU HAVE BEEN TRAINED&lt;/b&gt;&lt;br&gt;<br /> and have been added to the [[Equipment/Laser_Cutter/Training#Trained_Users|Trained Users]] list by one of the Owners<br /> &lt;/div&gt;<br /> <br /> To get trained on the laser cutter and be added to the qualified user list, you will need to arrange for a training session with one of the Laser Cutter Owners. <br /> <br /> If you'd like to arrange training, please see:<br /> * [[Equipment/Laser_Cutter/Training|Laser Cutter Training]]<br /> <br /> == Health and Safety ==<br /> <br /> The laser cutter is a potentially dangerous piece of equipment which must only be operated by members who have received appropriate training and who take due care. The top things to always remember when using the laser cutter are:<br /> * '''ONLY USE THE LASER CUTTER IF YOU ARE ON THE LIST OF TRAINED USERS'''<br /> * '''NEVER LEAVE THE LASER CUTTER RUNNING UNATTENDED'''<br /> * '''KNOW WHAT TO DO IF A FIRE BREAKS OUT'''<br /> * '''NEVER CUT MATERIALS THAT YOU DON'T KNOW ARE SAFE'''<br /> <br /> As a trained user, you should be very aware of the following risks and how to deal with them:<br /> <br /> '''FIRE (under normal operation)''' - Cutting at the wrong speed or the wrong power can result in the material igniting<br /> * You must watch the cutter at all times and be prepared to abort the job if problems occur<br /> * Small flashes of flame that don't hang around for a fraction of a second are acceptable, but any more is rare and not acceptable<br /> * If a fire does take, this is the process you should follow (from minor to major):<br /> ** Press &quot;pause&quot; (the same button you started the job with) - This will turn the laser off so no more heat enters, and assuming the flame goes out, you can press &quot;start&quot; for the job to continue where it left off<br /> ** Open the lid - With the job paused, you can open the lid to blow out the flame. Again, it is possible to re-close the lid and continue where you left off<br /> ** Move the material from under the laser head assuming safe to do so (so it doesn't damage the optics; alternatively send the laser to home/datum), and smother with a spare sheet of material or blow out<br /> ** Use the workshop CO2 extinguisher to extinguish the flame<br /> * You should also make a note in the log if any of this happens with associated materials and settings so we can keep track of any particular materials/settings we should look at <br /> <br /> '''FIRE (abnormal operation)''' - If the head gets stuck or something else goes wrong, ignition could happen much more suddenly or intensely<br /> * You must watch the cutter at all times and be prepared to abort the job if problems occur<br /> * If the head gets trapped (e.g. tomb-stoning of a piece, mechanical failure) or any other problem occurs that causes or could cause fire, this is the process you should follow:<br /> ** Hit the emergency stop<br /> ** Open the lid and move the material from under the laser head assuming safe to do so (so it doesn't damage the optics)<br /> ** Blow out, smother with a spare sheet of material, or use the CO2 extinguisher to extinguish the flame as appropriate<br /> * Ensure a Maintainer looks at the machine before it is brought back in to action if it is not obvious what went wrong and all is ok<br /> * You should also make a note in the log if any of this happens with associated materials and settings so we can keep track of any particular materials/settings we should look at <br /> <br /> '''FUMES''' - The laser cutting process will release different smoke and fumes depending on the material.<br /> * Never cut PVC or a material you are not sure is safe. When PVC is heated it releases chlorine gas, this mixes with the moisture in the air and the result is hydrochloric acid which is toxic to humans and corrosive to machines. <br /> * Ensure the filter is on and the cutter lid stays closed for a while after a job to allow the fumes to clear. <br /> * If you are feeling strange, think the fume build up is too much, or for any other reason you are unsure, stop the job.<br /> <br /> '''TRAPPING''' - The head and bed of the cutter can be moved by the front panel menu or programs in the machines memory. <br /> * Be careful when working inside the cutting area or with the lid open not to trap hands, hair, clothing or anything else. <br /> * Always check the machine for unexpected items that may have fallen in before closing the lid. <br /> * Do not attempt to climb into the machine!<br /> <br /> '''LASER BURNS/LIGHT''' - A 60W laser can do real damage. <br /> * The laser should be safe within the confines of the machine, and cut-off automatically when the lid is open (although this should not be relied upon). The top window is safe to look through during a job, but do not attempt to interfere with these windows or the laser or in any way invent some way to look at the laser.<br /> * Do not tamper with the laser cutter, or any interlocks. All side panels of the laser should always be closed and locked whilst the machine is plugged in. <br /> * Do not put metal in the laser cutter.<br /> <br /> == Can I cut it? ==<br /> <br /> If it's not on this list, the answer is &quot;NO YOU CAN'T CUT IT AT MAKESPACE&quot;. Even if other people say it's ok. Bear in mind that we can't ventilate externally like other people can.<br /> <br /> If it's something that isn't covered here, do ask on the forums and we'll look into it :)<br /> <br /> *Woody things<br /> ** Wood: yes! (be careful of fire)<br /> ** Plywood: yes if it is &quot;laser ply&quot;. Normal plywood has non-laser compatible glue<br /> ** MDF: no. Clogs up our filters and smells bad.<br /> ** LaserMDF: no. It produces perhaps 50% the gunk of MDF but still too much.<br /> ** Cork: yes, but it with a badly blackened edge, and won't cut very deeply --- try cutting from the back of your sheet and using the cut to guide a craft knife.<br /> <br /> *Plasticy things<br /> ** Acrylic / Perspex: yes!<br /> ** PVC/Vinyl: absolutely not. Produces chlorine.<br /> ** Silicone: we tried it with very limited success. A mm or two perhaps, anything else chars and doesn't cut.<br /> ** White Delrin/Acetal: yes with great care. Make sure filters running well. Don't open lid too quickly. Check for fumes and fire.<br /> ** Black Delrin/Acetal: no. contains carbon black which can be toxic.<br /> ** Teflon: no (it is toxic)<br /> ** Nylon: no (consult an owner)<br /> ** Polythene/polyethylene: no (consult an owner)<br /> ** Lexan/Polycarbonate: no (consult an owner)<br /> ** Polypropylene: yes just. You must clean the bed. It will cut up to about 2mm. It's not a great quality cut, but just about doable. Fire risk.<br /> ** GPPS / Polystyrene / HIPS in thin solid sheet form: maybe. ask owner to help. NO FOAM (it's highly flammable)<br /> <br /> *Papery things<br /> ** Card/Paper: yes! (be careful of fire)<br /> ** Tissue: yes if super super really careful (be REALLY careful of fire, have emergency procedure in place before you start)<br /> <br /> *Metally things<br /> ** Metal of any thickness doesn't cut. The surface can be engraved with a paint application. LMM6000 Surmark/Thermark has been tested and is suggested for use, but expensive. The owners suggest a speed of 800 and maximum power.<br /> <br /> *Exotics<br /> ** Fibre glass: no (unknown resin, glass particles)<br /> ** Carbon Fibre: no<br /> ** Slate: engravable for good effect<br /> <br /> Good list of info here: http://inventionstudio.gatech.edu/wiki/Laser_cutter (page disappeared, some time before 2016-12-12)<br /> <br /> == Instructions ==<br /> <br /> To use the laser cutter, you must have been trained and have had your name added to the trained user list; these instructions are not a substitute for this training. See the training section to understand how you can become qualified to use the laser cutter.<br /> <br /> Although not a requirement, it is recommended someone else trained is also present when using the laser cutter. Having two pairs of eyes helps avoid forgotten steps, allows for double checking, clarifications and discussions, and ensures a greater pool of experience is both present and being built up as the laser is used.<br /> <br /> '''Power Up'''<br /> <br /> Give the machine a quick visual check. Make sure that there is nothing left on the bed, the water reservoir of the chiller looks normal, and that the equipment has no obvious damage or signs of being out-of-action. If the bed looks like it has residue on it, give it a wipe with IPA and a cloth. <br /> <br /> Turn on primary switch on the trunking marked 'Laser'. The air filter system to the right of the laser cutter should start as should the air pump and the chiller. It should power up, make a decent amount of noise, and the lights should indicate the filter is in good condition (i.e. no need for replacement).<br /> <br /> Make sure the lid is closed. Turn on the laser using the key on the right hand side. The inspection lamp should come on, a satisfying hum start up, and the cutter go into doing its self-checks.<br /> <br /> Before doing any job, the laser should be left to warm up for 4-5 mins. While the machine warms up, power on the adjacent PC and start the LaserCut application from the desktop. During this time the water temperature shown on the chiller should drop from ambient temperature to the usual setting of 18C.<br /> <br /> '''Load your Design'''<br /> <br /> The PC software has an import facility ('''file &gt; import''') which seems to be happy taking AutoCAD 2004 DXF files and other formats. The workspace of the laser bed is represented as the workarea in the LaserCut software. If the import doesn't do what you want size-wise, you can select the whole image and then use the 'size' command from the drop down menu to set the dimension you want. Clicking on the three dots ... symbol will adjust the other axis in the same proportion (keeping the aspect ratio fixed). Selecting the 'centre on bed' option will locate your imported drawing on the centre of the machine's cutting bed.<br /> <br /> '''Assign Settings to Colours'''<br /> <br /> Each part of your drawing that is assigned a different colour can have a different cut action assigned. Each colour will appear on the menu on the right hand side of the screen with numbers related to power and speed of the laser which will be used for the colour. <br /> <br /> The main options are to Cut (line) or Engrave (raster fill). A marking on the material is a Cut. For each material and cutting depth required, a corresponding speed and power must be entered. The handbook provided with the machine gives suggested values for various materials but these should be considered as a starting point for a test. See the '''Power and Speed Settings''' section for our guidelines and experiences for these settings.<br /> <br /> '''Download to the Cutter'''<br /> <br /> Your drawing will feature a blue dot which represents the starting point of the laser; this is by default on the top right corner. In general, you will want to use &quot;immediate&quot; mode, which means this point represents wherever the laser is positioned when you start the job. You can also run the job in absolute mode by unchecking the box, making the job use absolute positioning on the workspace. <br /> <br /> To download, select Download and Download Current; the download option will by default call the file on the laser cutter 'LASER'.<br /> <br /> '''Set the Focus'''<br /> <br /> Before each job, the focus needs to be checked and set by adjusting the height of the bed, and thus the work piece, from the lens. The critical dimension here is 41mm and several gauges made of perspex will be left around the machine. This gauge needs to be a fit between the top surface of the material you intend to cut and the white plastic 'flap' on the lens piece. The height of the table is adjusted using the UP and DOWN buttons. Failure to set the distance correctly will result in an out of focus laser and much bigger (but lower powered) cut line. Always ensure there is clearance between the material and laser head before the head moves. <br /> <br /> '''Aligning and Testing the Job'''<br /> <br /> The cutter's menu will show the most recent downloaded file highlighted. Pressing the 'test' button will make the head travel along the square maximum extends of the cuts. This shows you that you have the material in the right place, and you have enough of it! You can do this repeatedly, moving the work piece by hand or the laser head using the arrow keys (after hitting ESC), until you are confident you have things where you want them.<br /> <br /> '''Cut the Job'''<br /> <br /> When happy with the location of the material, close the lid and press 'start' to start the cutter. Watch the head and at least at first be prepared to press the 'stop' button immediately if you find you are burning massive holes in your work piece! This goes back to doing some tests on a sample of your material and making sure you are happy with the cut speeds and power you have selected. You should stay near the cutter at all times and be prepared to pause it or stop it in the event of fire. <br /> <br /> &lt;span style=&quot;color:red&quot;&gt;'''DO NOT EVER LEAVE THE CUTTER UNATTENDED'''&lt;/span&gt;<br /> <br /> '''Finishing'''<br /> <br /> The end of the job is signified by a beep. Waiting a few moments for the exhaust pump to clear any remaining smoke is a good idea, especially with wood, and will limit the build up of smells in the rest of the workshop. Remove your work piece, ensuring that all parts are cleared from the bed of the machine.<br /> <br /> '''Power Down'''<br /> <br /> The cutter is turned off using the key switch, then the air filtering system with the green rocker switch. Shut down the PC and double check that everything is left in a safe state for the next user. <br /> <br /> '''Clean the bed of debris using the soft brush, then wipe down the bed using IPA and a cloth.'''<br /> <br /> If you have been cutting particularly 'dirty' materials, most notable MDF and Ply which leave a sticky residue then you will need to use the course side of one of the oven pads and lots of 'elbow grease'. Residue on the bed can impact the next persons' job so please make the effort to clean up and leave the cutter as you would wish to find it.<br /> <br /> Go away excited by what you can make and come back with lots more drawings!<br /> <br /> == Power and Speed Settings ==<br /> <br /> In due time we will try to build up a large sample stock of materials and record the values which work best. Here are the sample material tests we have so far:<br /> <br /> &lt;gallery&gt;<br /> File:Laser-schmoo-3mm-acrylic.JPG|3mm Acrylic<br /> File:Laser-schmoo-10mm-acrylic.JPG|10mm Acrylic<br /> File:Laser-schmoo-9mm-mdf.JPG|9mm MDF (note: do not cut MDF - see above!)<br /> &lt;/gallery&gt;<br /> <br /> Settings to get you started:<br /> *3mm Acrylic: Speed 12, Power 100, Corner power 100<br /> *5mm Acrylic: Speed 6, Power 100, Corner power 100<br /> *Acrylic shallow cut: Speed 30, power 50, corner power 50<br /> *Etching acrylic: Speed 400, Power 50, Spacing 0.05<br /> <br /> To make your own material test, a test grid can be downloaded here: [[Media:Test grid.zip]]<br /> <br /> == Tips &amp; Tricks ==<br /> <br /> * If the laser cutter's user interface does not seem to respond/do what you want, hit &quot;ESC&quot; to return to 'normal mode'.<br /> * The opaque white acrylic needs slightly stronger settings for surface cuts as they are not as visible as in the transparent acrylic (i.e., for similar effect you need a deeper cut). Otherwise seems to cut equivalently to transparent acrylics.<br /> * If you want a tight fit of pieces or very accurate sizing, keep in mind that the laser beam has a width of just over 0.1 mm (maybe 0.11 or 0.12 mm). So all exterior cut lines should be offset by 0.05 mm; you can do this very easily in the LaserCutter Software with the &quot;Offset&quot; tool (units are in mm, so enter '0.05' and select 'Outer').<br /> * The DXF file format stores values only (not values and units). The internal units in the LaserCutter are in mm. If you set your document's units to mm in the exporting CAD system it should work fine, but generally it is a good idea to have a piece of geometry of known length, e.g. a line 100mm long, or a box of known size around your design. This makes adjusting the scaling a lot easier.<br /> * If you want to export a DXF from Inkscape (which is a great, free vector drawing package), then make sure you do &quot;Object to path&quot; from the Path menu for the whole object and then during the export stage, untick both options for type of export. Choose mm as your unit.<br /> * There's now a page to help with Inkscape and our laser at [[Equipment/Laser_Cutter_Inkscape]]<br /> * If the jog buttons (arrow keys moving the laser head around) are only moving the head in small single steps rather than moving it continuously, make sure that the jog step size is set to 0.0mm in the Jog Settings section of the menu.<br /> <br /> === Material Usage ===<br /> You want to use as little material as possible to save money, we want you to use as little material as possible to reduce re-stocking burden and wastage.<br /> There's a neat tool you can use for packing SVG files into small spaces, find it here: http://svgnest.com/<br /> <br /> == Fixing up a job that went wrong ==<br /> <br /> If you messed up a job and, for example, some cut lines weren't cut, you might try to run the job again after recolouring all of the lines except the ones that didn't cut. You can then deselect those lines for output in the Cut/Engrave window on the top right of the Lasercut Interface, and this will keep your positioning.<br /> <br /> If your head has moved, you can try setting some lines to power 1, which should not cut anything, but allows you to see where the head is travelling.<br /> <br /> == Fixing strange issues ==<br /> <br /> ''Jaws has a FAQ on the desktop of her PC, with more useful hints, tricks, and solutions.''<br /> <br /> * Etching doesn't work<br /> ** Lines are not closed. LaserCut usually warns you about this. Ctrl-a to select all, then Tools-&gt;Unite Lines (0.001 should be fine).<br /> ** Two copies on top of each other. Copies on top of each other &quot;cancel out&quot; any etching. Delete one copy.<br /> ** Test with Menu-&gt;Laser-&gt;Simulate<br /> <br /> * LaserCut will not download to the laser cutter<br /> ** Check laser cutter isn't in a paused state<br /> ** Restart LaserCut on the PC. (We've not had any usb issues nor needed to restart the laser since upgrading the PC summer 2014).<br /> <br /> * Laser cuts things out 2+ times<br /> ** Check you don't have two copies loaded on top of each other<br /> ** Check it's not set to cut multiple times in LaserCut (this setting is right of the Cut/Engrave/Speed/Power settings)<br /> ** Check the laser front panel says &quot;001&quot; at the bottom. If not, press right arrow until the number is highlighted, then down to adjust back to 1, then press return.<br /> <br /> * Laser will only cut at the top right of the bed<br /> ** Download again with Immediate Mode ticked<br /> ** On laser panel, press return (I think?) then right twice (should select the bottom left option), then press return (I think).<br /> <br /> *You Hit Emergency stop<br /> ** E-M button needs twisting to re-activate<br /> ** If that fails - check the circuit breaker inside. From the back of the machine, you want to open the lower flap on the left side, which should be unlocked. Near to the back, there is a breaker board. Flip the flippy bit.<br /> <br /> == Material Stock ==<br /> For the stock we hold, please see the [[Equipment/Laser_Cutter_Stock|Laser cutter stock]] page.<br /> <br /> = Maintenance =<br /> <br /> The maintenance of the Laser Cutter is carried out by the Owners, with some basic maintenance being carried out by Users on every job.<br /> <br /> == Maintenance Schedule ==<br /> <br /> Continuous Maintenance ('''Every job, done by all Laser Cutter Users''')<br /> * Clean the laser bed with IPA and cloth or Swarfega wipes<br /> * Clean any debris off laser bed and surround using soft brush<br /> <br /> Basic Maintenance (Every week, done by Laser Cutter Maintainers)<br /> * Clean the laser lens with IPA and cotton buds<br /> * Oil the 3 runners with 3-in-one light oil <br /> * Thoroughly clean the laser bed with IPA and cloth<br /> * Check the water level in the cooling tank<br /> * Clean and remove debris from the machine base and catchment drawer<br /> <br /> Full Maintenance (Every 4 weeks, done by Laser Cutter Maintainers)<br /> * Check the water is clean in the cooling tank (i.e. no contamination/organic build up)<br /> * Check filter unit for filter renewal<br /> * Oil the 4 rise and fall lead screws with 3-in-one light oil<br /> * Check mirrors and clean with a disposable sachet lens cleaner cloth (only if needed, mirror coatings are delicate)<br /> * Work through mirror alignment procedure to check alignment of mirrors<br /> <br /> == Maintenance Log ==<br /> <br /> ''For full log, see laser cutter wall sheet''<br /> <br /> '''Filter Changes'''<br /> * Jaws: 10 Feb to 22 June 2016, slightly under 5 months, and falling<br /> * Betsy: Freshest data currently in filter unit, gave up on 24th of June<br /> <br /> <br /> '''Reactive Maintenance'''<br /> * 15th Jan 2013, Simon Ford: Laser cutter not powering up, with switching on via key gives no activity whatsoever. No recollection of it cutting out during a job (Alexis), so assume it just stopped turning on at some point. Filter box and power sockets confirmed OK. Diagnosis: RCD in right back panel of Laser reset to off, no obvious reason why. Switching back on brought everything back to life OK.<br /> * 22nd, Simon Ford; 29th, Nicholas - same again.<br /> <br /> * Apr 2014, Mat Cook and Diana Probst: after previous changing of chiller water (Roger et al) the pump was complaining of lack of flow. Changed water and filtered, removed small blockage from rubber hose on laser tube.<br /> <br /> * 16 Apr 2014, Toby and Diana: changed laser tube, refilled chiller. Laser cutter fully working.<br /> <br /> * 25 Oct 2014, Mat and Diana mended lid spring brace. Cutter working fully.<br /> <br /> '''Regular Maintenance'''<br /> * Week Number, Date, Type, Owner (Notes)<br /> <br /> 2013<br /> * January 7, Full, Chris @ HPCLaser'''<br /> * January 14, Basic, Simon Ford <br /> * January 21, Full, Simon Ford (running better than new :)'''<br /> * ...various maintenance events happened...<br /> * April 5th, Full, Simon Ford<br /> * July 1st, Full, David Barham (realigned mirrors)<br /> * July 15th, installed chiller<br /> <br /> 2014<br /> * 16 Apr 2014, mirror alignment and optics checked after re-installation of tube. All fine. Toby and Diana.<br /> * 19 May 2014, mirrors cleaned, earthing wire on lid tightened. Diana (and Mat's screwdriver)<br /> * 21 May 2014, cleaned lens with Mat Cook. Diana<br /> * 02 Jun 2014, removed and cleaned laser bed<br /> * 14 Sep 2014, cleaned lens and mirrors, realigned. Diana and Brian Starkey<br /> <br /> * 30 Jun 2014 Fitted microswitches in series with the magnetic &quot;lid closed&quot; detector. <br /> * ??? 2014 &quot;Jaws&quot; Second laser cutter acquired<br /> * ??? 2014 Fitted microswitch to Jaws<br /> <br /> == Maintenance Shopping List ==<br /> <br /> * 3-in-one light oil <br /> * Cotton Buds<br /> * Lens cleaner sachets<br /> * Soft paint/cleaning brush<br /> * Thermometer for water tank<br /> * Hand held CO2 extinguisher<br /> <br /> = Further Information =<br /> <br /> * [http://hpclaser.co.uk/index.php?main_page=product_info&amp;cPath=1&amp;products_id=11 LS 6090 PRO Laser Product Page]<br /> * [http://hpclaser.co.uk/index.php?main_page=page&amp;id=5&amp;chapter=2 HPCLaser Technical Info]<br /> * [http://www.laserscript.co.uk/phpBB3/ Laserscript Forum]<br /> <br /> LaserCut 5.3<br /> * [http://www.leetro.com/english/sale/35.html Homepage]<br /> * [http://www.leetro.com/english/down/LaserCut5.3%20Manual%20V1.6.pdf Manual]<br /> <br /> == Installation ==<br /> <br /> &lt;gallery&gt;<br /> File:Laser_-_van.JPG<br /> File:Makespace-laser-install-02.JPG<br /> File:Laser_-_building_2.JPG<br /> File:Laser_-_building.JPG<br /> &lt;/gallery&gt;<br /> <br /> == Purchase ==<br /> <br /> Full Purchase, Delivery and Installation (£6865.00+vat = £8238.00)<br /> * [http://hpclaser.co.uk/index.php?main_page=product_info&amp;cPath=1&amp;products_id=11 LS 6090 PRO Laser engraving and cutting machine, 600mm by 900mm 60W] (£5250.00+vat)<br /> * [http://hpclaser.co.uk/index.php?main_page=product_info&amp;cPath=2&amp;products_id=34 Laser Fume Filter] (£1250.00+vat)<br /> * Delivery (£190+vat)<br /> * Installation/Training (£175+vat)<br /> <br /> == Repairs ==<br /> <br /> We expect to have to change the following parts for general maintenance:<br /> * The laser tube (guess every 6-12 months)<br /> * The filter (guess every 3-6 months)<br /> * The optics (guess every 6-12 months)<br /> <br /> Maintenance and Spares:<br /> * [http://hpclaser.co.uk/index.php?main_page=product_info&amp;cPath=2&amp;products_id=3 60 watt C02 laser tube] (£275.00+vat)<br /> * [http://hpclaser.co.uk/index.php?main_page=product_info&amp;cPath=2&amp;products_id=12 50 mm Focus Meniscus Lens] (£75.00+vat)<br /> * Estimate for Call Out (£200.00)</div>

JCGS http://wiki.makespace.org/Equipment/Laser_Cutter 2016-12-12T14:11:44Z

<p>JCGS: Result from when I cut cork with it</p> <hr /> <div><br /> {{RedTool}}<br /> <br /> [[Equipment|Equipment]] / Laser Cutter<br /> <br /> [[File:Makespace-laser-cutter.JPG|thumb|460px|right|Our LS6090 PRO Laser Cutter]]<br /> <br /> = Summary =<br /> <br /> We have two LS 6090 PRO Laser Cutters. Each has a working area of 900mm by 600mm, and is powered by a 60w CO2 Water Cooled Laser Tube that can engrave and cut through materials such as wood, plastic, card, leather, fabrics, up to about 10-15mm thick (note, it can not cut metal). The laser cut is approximately 0.15mm wide, and a job can take a few seconds through to tens of minutes depending on material thickness and design complexity. <br /> <br /> We have dedicated PCs running LaserCut 5.3 software to import, prepare and download jobs to the Laser Cutter. It can import various formats, with DXF being the most commonly used, so various software packages can be used to create your designs.<br /> <br /> Here are some examples of laser jobs we've run (please add a photo of yours any time you do a job!)<br /> <br /> &lt;gallery&gt;<br /> File:Laser-cut-focus-tool.JPG<br /> File:Laser-cut-front-panels.JPG<br /> File:Laser-cut-lizards.JPG<br /> File:Laser-cut-m-and-s.JPG<br /> File:Laser-cut-model-building.JPG<br /> File:Laser-cut-ply-m.JPG<br /> File:Laser_output_-_makespace_arrow.JPG<br /> File:Laser_box.jpg<br /> File:Croc-small.jpg<br /> File:LaserCutter_Jobs_1.jpg<br /> File:LaserCutterGallery_20130328.jpg<br /> File:LasercutSettlers.jpg<br /> File:Wolfstock1.jpg<br /> File:Mug-holder.jpg<br /> File:2013-10-21 20.10.06.jpg<br /> File:Indy jigster.png<br /> &lt;/gallery&gt;<br /> <br /> = Using the Laser Cutter =<br /> <br /> The laser cutter is a great way to easily produce accurate and complex 2D forms in various materials, and can be designed for with limited experience in various drawing or CAD applications. At the same time, it is an expensive tool with real risk of injury and fire, so is very important you know how to use it to avoid damaging yourself and the machine. '''You must only use the laser cutter if you have been trained, and if you are ever in any doubt about something, please ask for assistance.'''<br /> <br /> == Owners ==<br /> <br /> The Owners are those who have volunteered to be in charge of the laser cutter, organising maintenance, responding to technical issues and generally being a point of contact. The current Owners of the Laser Cutter are:<br /> <br /> * [[User:Mat-C|Mat Cook]]<br /> * [[User:DianaProbst|Diana Probst]]<br /> * Owners who are a little less current, but may still be able to help:<br /> ** [[User:Simon|Simon Ford]]<br /> ** [[User:Barhamd|David Barham]]<br /> ** [[User:Nickcadsoftuk|Nick Johnson]]<br /> <br /> == Trainers ==<br /> <br /> The Trainers are those who have volunteered to teach others to use the laser cutter and to promote good working practice. The current Trainers for the Laser Cutter are:<br /> <br /> * Brian Starkey<br /> * [[User:stevancw|Stevan Wing]]<br /> * [[User:Mat-C|Mat Cook]]<br /> * [[User:robv|Rob Voisey]]<br /> <br /> * Currently slightly less frequent trainers are:<br /> ** Martin de Selincourt<br /> ** [[User:Simon|Simon Ford]]<br /> ** [[User:Barhamd|David Barham]]<br /> ** [[User:Nickcadsoftuk|Nick Johnson]]<br /> ** [[User:Tmonca|Toby Moncaster]]<br /> <br /> <br /> If you have any questions, problems or concerns around the laser cutter, please use the forum page:<br /> * [http://makespace.org/forum/viewtopic.php?f=19&amp;t=45 Laser Cutter Log]<br /> <br /> For the old mailing list thread see here:<br /> * [https://groups.google.com/d/topic/cammakespace/Tmce2iKVzD8/discussion Log : Laser Cutter]<br /> <br /> == Training ==<br /> <br /> &lt;div style=&quot;background:#FADADD; border:1px solid #FFC0CB; padding:5px&quot;&gt;<br /> &lt;b&gt;YOU CAN ONLY USE THE LASER CUTTER IF YOU HAVE BEEN TRAINED&lt;/b&gt;&lt;br&gt;<br /> and have been added to the [[Equipment/Laser_Cutter/Training#Trained_Users|Trained Users]] list by one of the Owners<br /> &lt;/div&gt;<br /> <br /> To get trained on the laser cutter and be added to the qualified user list, you will need to arrange for a training session with one of the Laser Cutter Owners. <br /> <br /> If you'd like to arrange training, please see:<br /> * [[Equipment/Laser_Cutter/Training|Laser Cutter Training]]<br /> <br /> == Health and Safety ==<br /> <br /> The laser cutter is a potentially dangerous piece of equipment which must only be operated by members who have received appropriate training and who take due care. The top things to always remember when using the laser cutter are:<br /> * '''ONLY USE THE LASER CUTTER IF YOU ARE ON THE LIST OF TRAINED USERS'''<br /> * '''NEVER LEAVE THE LASER CUTTER RUNNING UNATTENDED'''<br /> * '''KNOW WHAT TO DO IF A FIRE BREAKS OUT'''<br /> * '''NEVER CUT MATERIALS THAT YOU DON'T KNOW ARE SAFE'''<br /> <br /> As a trained user, you should be very aware of the following risks and how to deal with them:<br /> <br /> '''FIRE (under normal operation)''' - Cutting at the wrong speed or the wrong power can result in the material igniting<br /> * You must watch the cutter at all times and be prepared to abort the job if problems occur<br /> * Small flashes of flame that don't hang around for a fraction of a second are acceptable, but any more is rare and not acceptable<br /> * If a fire does take, this is the process you should follow (from minor to major):<br /> ** Press &quot;pause&quot; (the same button you started the job with) - This will turn the laser off so no more heat enters, and assuming the flame goes out, you can press &quot;start&quot; for the job to continue where it left off<br /> ** Open the lid - With the job paused, you can open the lid to blow out the flame. Again, it is possible to re-close the lid and continue where you left off<br /> ** Move the material from under the laser head assuming safe to do so (so it doesn't damage the optics; alternatively send the laser to home/datum), and smother with a spare sheet of material or blow out<br /> ** Use the workshop CO2 extinguisher to extinguish the flame<br /> * You should also make a note in the log if any of this happens with associated materials and settings so we can keep track of any particular materials/settings we should look at <br /> <br /> '''FIRE (abnormal operation)''' - If the head gets stuck or something else goes wrong, ignition could happen much more suddenly or intensely<br /> * You must watch the cutter at all times and be prepared to abort the job if problems occur<br /> * If the head gets trapped (e.g. tomb-stoning of a piece, mechanical failure) or any other problem occurs that causes or could cause fire, this is the process you should follow:<br /> ** Hit the emergency stop<br /> ** Open the lid and move the material from under the laser head assuming safe to do so (so it doesn't damage the optics)<br /> ** Blow out, smother with a spare sheet of material, or use the CO2 extinguisher to extinguish the flame as appropriate<br /> * Ensure a Maintainer looks at the machine before it is brought back in to action if it is not obvious what went wrong and all is ok<br /> * You should also make a note in the log if any of this happens with associated materials and settings so we can keep track of any particular materials/settings we should look at <br /> <br /> '''FUMES''' - The laser cutting process will release different smoke and fumes depending on the material.<br /> * Never cut PVC or a material you are not sure is safe. When PVC is heated it releases chlorine gas, this mixes with the moisture in the air and the result is hydrochloric acid which is toxic to humans and corrosive to machines. <br /> * Ensure the filter is on and the cutter lid stays closed for a while after a job to allow the fumes to clear. <br /> * If you are feeling strange, think the fume build up is too much, or for any other reason you are unsure, stop the job.<br /> <br /> '''TRAPPING''' - The head and bed of the cutter can be moved by the front panel menu or programs in the machines memory. <br /> * Be careful when working inside the cutting area or with the lid open not to trap hands, hair, clothing or anything else. <br /> * Always check the machine for unexpected items that may have fallen in before closing the lid. <br /> * Do not attempt to climb into the machine!<br /> <br /> '''LASER BURNS/LIGHT''' - A 60W laser can do real damage. <br /> * The laser should be safe within the confines of the machine, and cut-off automatically when the lid is open (although this should not be relied upon). The top window is safe to look through during a job, but do not attempt to interfere with these windows or the laser or in any way invent some way to look at the laser.<br /> * Do not tamper with the laser cutter, or any interlocks. All side panels of the laser should always be closed and locked whilst the machine is plugged in. <br /> * Do not put metal in the laser cutter.<br /> <br /> == Can I cut it? ==<br /> <br /> If it's not on this list, the answer is &quot;NO YOU CAN'T CUT IT AT MAKESPACE&quot;. Even if other people say it's ok. Bear in mind that we can't ventilate externally like other people can.<br /> <br /> If it's something that isn't covered here, do ask on the forums and we'll look into it :)<br /> <br /> *Woody things<br /> ** Wood: yes! (be careful of fire)<br /> ** Plywood: yes if it is &quot;laser ply&quot;. Normal plywood has non-laser compatible glue<br /> ** MDF: no. Clogs up our filters and smells bad.<br /> ** LaserMDF: no. It produces perhaps 50% the gunk of MDF but still too much.<br /> ** Cork: yes, but it with a badly blackened edge, and won't cut very deeply --- try cutting from the back of your sheet and using the cut to guide a craft knife.<br /> <br /> *Plasticy things<br /> ** Acrylic / Perspex: yes!<br /> ** PVC/Vinyl: absolutely not. Produces chlorine.<br /> ** Silicone: we tried it with very limited success. A mm or two perhaps, anything else chars and doesn't cut.<br /> ** White Delrin/Acetal: yes with great care. Make sure filters running well. Don't open lid too quickly. Check for fumes and fire.<br /> ** Black Delrin/Acetal: no. contains carbon black which can be toxic.<br /> ** Teflon: no (it is toxic)<br /> ** Nylon: no (consult an owner)<br /> ** Polythene/polyethylene: no (consult an owner)<br /> ** Lexan/Polycarbonate: no (consult an owner)<br /> ** Polypropylene: yes just. You must clean the bed. It will cut up to about 2mm. It's not a great quality cut, but just about doable. Fire risk.<br /> ** GPPS / Polystyrene / HIPS in thin solid sheet form: maybe. ask owner to help. NO FOAM (it's highly flammable)<br /> <br /> *Papery things<br /> ** Card/Paper: yes! (be careful of fire)<br /> ** Tissue: yes if super super really careful (be REALLY careful of fire, have emergency procedure in place before you start)<br /> <br /> *Metally things<br /> ** Metal of any thickness doesn't cut. The surface can be engraved with a paint application. LMM6000 Surmark/Thermark has been tested and is suggested for use, but expensive. The owners suggest a speed of 800 and maximum power.<br /> <br /> *Exotics<br /> ** Fibre glass: no (unknown resin, glass particles)<br /> ** Carbon Fibre: no<br /> ** Slate: engravable for good effect<br /> <br /> Good list of info here: http://inventionstudio.gatech.edu/wiki/Laser_cutter<br /> <br /> == Instructions ==<br /> <br /> To use the laser cutter, you must have been trained and have had your name added to the trained user list; these instructions are not a substitute for this training. See the training section to understand how you can become qualified to use the laser cutter.<br /> <br /> Although not a requirement, it is recommended someone else trained is also present when using the laser cutter. Having two pairs of eyes helps avoid forgotten steps, allows for double checking, clarifications and discussions, and ensures a greater pool of experience is both present and being built up as the laser is used.<br /> <br /> '''Power Up'''<br /> <br /> Give the machine a quick visual check. Make sure that there is nothing left on the bed, the water reservoir of the chiller looks normal, and that the equipment has no obvious damage or signs of being out-of-action. If the bed looks like it has residue on it, give it a wipe with IPA and a cloth. <br /> <br /> Turn on primary switch on the trunking marked 'Laser'. The air filter system to the right of the laser cutter should start as should the air pump and the chiller. It should power up, make a decent amount of noise, and the lights should indicate the filter is in good condition (i.e. no need for replacement).<br /> <br /> Make sure the lid is closed. Turn on the laser using the key on the right hand side. The inspection lamp should come on, a satisfying hum start up, and the cutter go into doing its self-checks.<br /> <br /> Before doing any job, the laser should be left to warm up for 4-5 mins. While the machine warms up, power on the adjacent PC and start the LaserCut application from the desktop. During this time the water temperature shown on the chiller should drop from ambient temperature to the usual setting of 18C.<br /> <br /> '''Load your Design'''<br /> <br /> The PC software has an import facility ('''file &gt; import''') which seems to be happy taking AutoCAD 2004 DXF files and other formats. The workspace of the laser bed is represented as the workarea in the LaserCut software. If the import doesn't do what you want size-wise, you can select the whole image and then use the 'size' command from the drop down menu to set the dimension you want. Clicking on the three dots ... symbol will adjust the other axis in the same proportion (keeping the aspect ratio fixed). Selecting the 'centre on bed' option will locate your imported drawing on the centre of the machine's cutting bed.<br /> <br /> '''Assign Settings to Colours'''<br /> <br /> Each part of your drawing that is assigned a different colour can have a different cut action assigned. Each colour will appear on the menu on the right hand side of the screen with numbers related to power and speed of the laser which will be used for the colour. <br /> <br /> The main options are to Cut (line) or Engrave (raster fill). A marking on the material is a Cut. For each material and cutting depth required, a corresponding speed and power must be entered. The handbook provided with the machine gives suggested values for various materials but these should be considered as a starting point for a test. See the '''Power and Speed Settings''' section for our guidelines and experiences for these settings.<br /> <br /> '''Download to the Cutter'''<br /> <br /> Your drawing will feature a blue dot which represents the starting point of the laser; this is by default on the top right corner. In general, you will want to use &quot;immediate&quot; mode, which means this point represents wherever the laser is positioned when you start the job. You can also run the job in absolute mode by unchecking the box, making the job use absolute positioning on the workspace. <br /> <br /> To download, select Download and Download Current; the download option will by default call the file on the laser cutter 'LASER'.<br /> <br /> '''Set the Focus'''<br /> <br /> Before each job, the focus needs to be checked and set by adjusting the height of the bed, and thus the work piece, from the lens. The critical dimension here is 41mm and several gauges made of perspex will be left around the machine. This gauge needs to be a fit between the top surface of the material you intend to cut and the white plastic 'flap' on the lens piece. The height of the table is adjusted using the UP and DOWN buttons. Failure to set the distance correctly will result in an out of focus laser and much bigger (but lower powered) cut line. Always ensure there is clearance between the material and laser head before the head moves. <br /> <br /> '''Aligning and Testing the Job'''<br /> <br /> The cutter's menu will show the most recent downloaded file highlighted. Pressing the 'test' button will make the head travel along the square maximum extends of the cuts. This shows you that you have the material in the right place, and you have enough of it! You can do this repeatedly, moving the work piece by hand or the laser head using the arrow keys (after hitting ESC), until you are confident you have things where you want them.<br /> <br /> '''Cut the Job'''<br /> <br /> When happy with the location of the material, close the lid and press 'start' to start the cutter. Watch the head and at least at first be prepared to press the 'stop' button immediately if you find you are burning massive holes in your work piece! This goes back to doing some tests on a sample of your material and making sure you are happy with the cut speeds and power you have selected. You should stay near the cutter at all times and be prepared to pause it or stop it in the event of fire. <br /> <br /> &lt;span style=&quot;color:red&quot;&gt;'''DO NOT EVER LEAVE THE CUTTER UNATTENDED'''&lt;/span&gt;<br /> <br /> '''Finishing'''<br /> <br /> The end of the job is signified by a beep. Waiting a few moments for the exhaust pump to clear any remaining smoke is a good idea, especially with wood, and will limit the build up of smells in the rest of the workshop. Remove your work piece, ensuring that all parts are cleared from the bed of the machine.<br /> <br /> '''Power Down'''<br /> <br /> The cutter is turned off using the key switch, then the air filtering system with the green rocker switch. Shut down the PC and double check that everything is left in a safe state for the next user. <br /> <br /> '''Clean the bed of debris using the soft brush, then wipe down the bed using IPA and a cloth.'''<br /> <br /> If you have been cutting particularly 'dirty' materials, most notable MDF and Ply which leave a sticky residue then you will need to use the course side of one of the oven pads and lots of 'elbow grease'. Residue on the bed can impact the next persons' job so please make the effort to clean up and leave the cutter as you would wish to find it.<br /> <br /> Go away excited by what you can make and come back with lots more drawings!<br /> <br /> == Power and Speed Settings ==<br /> <br /> In due time we will try to build up a large sample stock of materials and record the values which work best. Here are the sample material tests we have so far:<br /> <br /> &lt;gallery&gt;<br /> File:Laser-schmoo-3mm-acrylic.JPG|3mm Acrylic<br /> File:Laser-schmoo-10mm-acrylic.JPG|10mm Acrylic<br /> File:Laser-schmoo-9mm-mdf.JPG|9mm MDF (note: do not cut MDF - see above!)<br /> &lt;/gallery&gt;<br /> <br /> Settings to get you started:<br /> *3mm Acrylic: Speed 12, Power 100, Corner power 100<br /> *5mm Acrylic: Speed 6, Power 100, Corner power 100<br /> *Acrylic shallow cut: Speed 30, power 50, corner power 50<br /> *Etching acrylic: Speed 400, Power 50, Spacing 0.05<br /> <br /> To make your own material test, a test grid can be downloaded here: [[Media:Test grid.zip]]<br /> <br /> == Tips &amp; Tricks ==<br /> <br /> * If the laser cutter's user interface does not seem to respond/do what you want, hit &quot;ESC&quot; to return to 'normal mode'.<br /> * The opaque white acrylic needs slightly stronger settings for surface cuts as they are not as visible as in the transparent acrylic (i.e., for similar effect you need a deeper cut). Otherwise seems to cut equivalently to transparent acrylics.<br /> * If you want a tight fit of pieces or very accurate sizing, keep in mind that the laser beam has a width of just over 0.1 mm (maybe 0.11 or 0.12 mm). So all exterior cut lines should be offset by 0.05 mm; you can do this very easily in the LaserCutter Software with the &quot;Offset&quot; tool (units are in mm, so enter '0.05' and select 'Outer').<br /> * The DXF file format stores values only (not values and units). The internal units in the LaserCutter are in mm. If you set your document's units to mm in the exporting CAD system it should work fine, but generally it is a good idea to have a piece of geometry of known length, e.g. a line 100mm long, or a box of known size around your design. This makes adjusting the scaling a lot easier.<br /> * If you want to export a DXF from Inkscape (which is a great, free vector drawing package), then make sure you do &quot;Object to path&quot; from the Path menu for the whole object and then during the export stage, untick both options for type of export. Choose mm as your unit.<br /> * There's now a page to help with Inkscape and our laser at [[Equipment/Laser_Cutter_Inkscape]]<br /> * If the jog buttons (arrow keys moving the laser head around) are only moving the head in small single steps rather than moving it continuously, make sure that the jog step size is set to 0.0mm in the Jog Settings section of the menu.<br /> <br /> === Material Usage ===<br /> You want to use as little material as possible to save money, we want you to use as little material as possible to reduce re-stocking burden and wastage.<br /> There's a neat tool you can use for packing SVG files into small spaces, find it here: http://svgnest.com/<br /> <br /> == Fixing up a job that went wrong ==<br /> <br /> If you messed up a job and, for example, some cut lines weren't cut, you might try to run the job again after recolouring all of the lines except the ones that didn't cut. You can then deselect those lines for output in the Cut/Engrave window on the top right of the Lasercut Interface, and this will keep your positioning.<br /> <br /> If your head has moved, you can try setting some lines to power 1, which should not cut anything, but allows you to see where the head is travelling.<br /> <br /> == Fixing strange issues ==<br /> <br /> ''Jaws has a FAQ on the desktop of her PC, with more useful hints, tricks, and solutions.''<br /> <br /> * Etching doesn't work<br /> ** Lines are not closed. LaserCut usually warns you about this. Ctrl-a to select all, then Tools-&gt;Unite Lines (0.001 should be fine).<br /> ** Two copies on top of each other. Copies on top of each other &quot;cancel out&quot; any etching. Delete one copy.<br /> ** Test with Menu-&gt;Laser-&gt;Simulate<br /> <br /> * LaserCut will not download to the laser cutter<br /> ** Check laser cutter isn't in a paused state<br /> ** Restart LaserCut on the PC. (We've not had any usb issues nor needed to restart the laser since upgrading the PC summer 2014).<br /> <br /> * Laser cuts things out 2+ times<br /> ** Check you don't have two copies loaded on top of each other<br /> ** Check it's not set to cut multiple times in LaserCut (this setting is right of the Cut/Engrave/Speed/Power settings)<br /> ** Check the laser front panel says &quot;001&quot; at the bottom. If not, press right arrow until the number is highlighted, then down to adjust back to 1, then press return.<br /> <br /> * Laser will only cut at the top right of the bed<br /> ** Download again with Immediate Mode ticked<br /> ** On laser panel, press return (I think?) then right twice (should select the bottom left option), then press return (I think).<br /> <br /> *You Hit Emergency stop<br /> ** E-M button needs twisting to re-activate<br /> ** If that fails - check the circuit breaker inside. From the back of the machine, you want to open the lower flap on the left side, which should be unlocked. Near to the back, there is a breaker board. Flip the flippy bit.<br /> <br /> == Material Stock ==<br /> For the stock we hold, please see the [[Equipment/Laser_Cutter_Stock|Laser cutter stock]] page.<br /> <br /> = Maintenance =<br /> <br /> The maintenance of the Laser Cutter is carried out by the Owners, with some basic maintenance being carried out by Users on every job.<br /> <br /> == Maintenance Schedule ==<br /> <br /> Continuous Maintenance ('''Every job, done by all Laser Cutter Users''')<br /> * Clean the laser bed with IPA and cloth or Swarfega wipes<br /> * Clean any debris off laser bed and surround using soft brush<br /> <br /> Basic Maintenance (Every week, done by Laser Cutter Maintainers)<br /> * Clean the laser lens with IPA and cotton buds<br /> * Oil the 3 runners with 3-in-one light oil <br /> * Thoroughly clean the laser bed with IPA and cloth<br /> * Check the water level in the cooling tank<br /> * Clean and remove debris from the machine base and catchment drawer<br /> <br /> Full Maintenance (Every 4 weeks, done by Laser Cutter Maintainers)<br /> * Check the water is clean in the cooling tank (i.e. no contamination/organic build up)<br /> * Check filter unit for filter renewal<br /> * Oil the 4 rise and fall lead screws with 3-in-one light oil<br /> * Check mirrors and clean with a disposable sachet lens cleaner cloth (only if needed, mirror coatings are delicate)<br /> * Work through mirror alignment procedure to check alignment of mirrors<br /> <br /> == Maintenance Log ==<br /> <br /> ''For full log, see laser cutter wall sheet''<br /> <br /> '''Filter Changes'''<br /> * Jaws: 10 Feb to 22 June 2016, slightly under 5 months, and falling<br /> * Betsy: Freshest data currently in filter unit, gave up on 24th of June<br /> <br /> <br /> '''Reactive Maintenance'''<br /> * 15th Jan 2013, Simon Ford: Laser cutter not powering up, with switching on via key gives no activity whatsoever. No recollection of it cutting out during a job (Alexis), so assume it just stopped turning on at some point. Filter box and power sockets confirmed OK. Diagnosis: RCD in right back panel of Laser reset to off, no obvious reason why. Switching back on brought everything back to life OK.<br /> * 22nd, Simon Ford; 29th, Nicholas - same again.<br /> <br /> * Apr 2014, Mat Cook and Diana Probst: after previous changing of chiller water (Roger et al) the pump was complaining of lack of flow. Changed water and filtered, removed small blockage from rubber hose on laser tube.<br /> <br /> * 16 Apr 2014, Toby and Diana: changed laser tube, refilled chiller. Laser cutter fully working.<br /> <br /> * 25 Oct 2014, Mat and Diana mended lid spring brace. Cutter working fully.<br /> <br /> '''Regular Maintenance'''<br /> * Week Number, Date, Type, Owner (Notes)<br /> <br /> 2013<br /> * January 7, Full, Chris @ HPCLaser'''<br /> * January 14, Basic, Simon Ford <br /> * January 21, Full, Simon Ford (running better than new :)'''<br /> * ...various maintenance events happened...<br /> * April 5th, Full, Simon Ford<br /> * July 1st, Full, David Barham (realigned mirrors)<br /> * July 15th, installed chiller<br /> <br /> 2014<br /> * 16 Apr 2014, mirror alignment and optics checked after re-installation of tube. All fine. Toby and Diana.<br /> * 19 May 2014, mirrors cleaned, earthing wire on lid tightened. Diana (and Mat's screwdriver)<br /> * 21 May 2014, cleaned lens with Mat Cook. Diana<br /> * 02 Jun 2014, removed and cleaned laser bed<br /> * 14 Sep 2014, cleaned lens and mirrors, realigned. Diana and Brian Starkey<br /> <br /> * 30 Jun 2014 Fitted microswitches in series with the magnetic &quot;lid closed&quot; detector. <br /> * ??? 2014 &quot;Jaws&quot; Second laser cutter acquired<br /> * ??? 2014 Fitted microswitch to Jaws<br /> <br /> == Maintenance Shopping List ==<br /> <br /> * 3-in-one light oil <br /> * Cotton Buds<br /> * Lens cleaner sachets<br /> * Soft paint/cleaning brush<br /> * Thermometer for water tank<br /> * Hand held CO2 extinguisher<br /> <br /> = Further Information =<br /> <br /> * [http://hpclaser.co.uk/index.php?main_page=product_info&amp;cPath=1&amp;products_id=11 LS 6090 PRO Laser Product Page]<br /> * [http://hpclaser.co.uk/index.php?main_page=page&amp;id=5&amp;chapter=2 HPCLaser Technical Info]<br /> * [http://www.laserscript.co.uk/phpBB3/ Laserscript Forum]<br /> <br /> LaserCut 5.3<br /> * [http://www.leetro.com/english/sale/35.html Homepage]<br /> * [http://www.leetro.com/english/down/LaserCut5.3%20Manual%20V1.6.pdf Manual]<br /> <br /> == Installation ==<br /> <br /> &lt;gallery&gt;<br /> File:Laser_-_van.JPG<br /> File:Makespace-laser-install-02.JPG<br /> File:Laser_-_building_2.JPG<br /> File:Laser_-_building.JPG<br /> &lt;/gallery&gt;<br /> <br /> == Purchase ==<br /> <br /> Full Purchase, Delivery and Installation (£6865.00+vat = £8238.00)<br /> * [http://hpclaser.co.uk/index.php?main_page=product_info&amp;cPath=1&amp;products_id=11 LS 6090 PRO Laser engraving and cutting machine, 600mm by 900mm 60W] (£5250.00+vat)<br /> * [http://hpclaser.co.uk/index.php?main_page=product_info&amp;cPath=2&amp;products_id=34 Laser Fume Filter] (£1250.00+vat)<br /> * Delivery (£190+vat)<br /> * Installation/Training (£175+vat)<br /> <br /> == Repairs ==<br /> <br /> We expect to have to change the following parts for general maintenance:<br /> * The laser tube (guess every 6-12 months)<br /> * The filter (guess every 3-6 months)<br /> * The optics (guess every 6-12 months)<br /> <br /> Maintenance and Spares:<br /> * [http://hpclaser.co.uk/index.php?main_page=product_info&amp;cPath=2&amp;products_id=3 60 watt C02 laser tube] (£275.00+vat)<br /> * [http://hpclaser.co.uk/index.php?main_page=product_info&amp;cPath=2&amp;products_id=12 50 mm Focus Meniscus Lens] (£75.00+vat)<br /> * Estimate for Call Out (£200.00)</div>

JCGS http://wiki.makespace.org/Stock_list 2015-11-02T13:45:33Z

<p>JCGS: </p> <hr /> <div>See also [[Shopping List]]<br /> <br /> {|<br /> |-<br /> ! Item<br /> ! Location<br /> ! Suggested level<br /> ! Available from<br /> ! Item details, part number, etc<br /> |- <br /> | Bin liner bags<br /> | Under sink in Cakespace<br /> | At least one roll<br /> | Supermarkets, DIY stores<br /> |-<br /> | Blue tissue paper<br /> | ?<br /> | A bag of rolls<br /> | Screwfix?<br /> |-<br /> | Badger labels<br /> | Table in corridor, spares in ?<br /> | One box?<br /> | ?<br /> |-<br /> | Whiteboard pens<br /> | Stationery drawers under printers<br /> |<br /> | Staples etc<br /> |-<br /> | Indelible marker pens<br /> | Stationery drawers under printers<br /> |<br /> | Staples etc<br /> |-<br /> | Microfibre cloths<br /> |<br /> |<br /> |-<br /> | Dymo labeller tape to fit our Dymos<br /> |-<br /> | A4 paper<br /> | Drawers under printers<br /> |-<br /> | Liquid soap<br /> | Cupboards in Cakespace<br /> |-<br /> | Washing-up liquid<br /> | Cupboards in Cakespace<br /> |-<br /> | Gaffer tape<br /> | Louvre bins on wall near back door?<br /> |<br /> | DIY shops<br /> |-<br /> | Teabags, coffee powder<br /> | Cakespace<br /> |<br /> | Supermarkets<br /> |-<br /> | Nuts and bolts, M3-M6 at least<br /> | Secure workshop<br /> | At least a dozen in each size<br /> | eBay --- &quot;Aruncas&quot; delivers quite fast (JCGS' suggestion)<br /> |}</div>

JCGS http://wiki.makespace.org/Stock_list 2015-11-02T13:43:31Z

<p>JCGS: </p> <hr /> <div>See also [[Shopping List]]<br /> <br /> {|<br /> |-<br /> ! Item<br /> ! Location<br /> ! Suggested level<br /> ! Available from<br /> ! Item details, part number, etc<br /> |- <br /> | Bin liner bags<br /> | Under sink in Cakespace<br /> | At least one roll<br /> | Supermarkets, DIY stores<br /> |-<br /> | Blue tissue paper<br /> | ?<br /> | A bag of rolls<br /> | Screwfix?<br /> |-<br /> | Badger labels<br /> | Table in corridor, spares in ?<br /> | One box?<br /> | ?<br /> |-<br /> | Whiteboard pens<br /> | Stationery drawers under printers<br /> |<br /> | Staples etc<br /> |-<br /> | Indelible marker pens<br /> | Stationery drawers under printers<br /> |<br /> | Staples etc<br /> |-<br /> | Microfibre cloths<br /> |<br /> |<br /> |-<br /> | Dymo labeller tape to fit our Dymos<br /> |-<br /> | A4 paper<br /> | Drawers under printers<br /> |-<br /> | Liquid soap<br /> | Cupboards in Cakespace<br /> |-<br /> | Washing-up liquid<br /> | Cupboards in Cakespace<br /> |-<br /> | Gaffer tape<br /> | Louvre bins on wall near back door?<br /> |<br /> | DIY shops<br /> |-<br /> | Teabags, coffee powder<br /> | Cakespace<br /> |<br /> | Supermarkets<br /> |}</div>

JCGS http://wiki.makespace.org/Stock_list 2015-11-02T13:41:00Z

<p>JCGS: </p> <hr /> <div>See also [[Shopping List]]<br /> <br /> {|<br /> |-<br /> ! Item<br /> ! Location<br /> ! Suggested level<br /> ! Available from<br /> ! Item details, part number, etc<br /> |- <br /> | Bin liner bags<br /> | Under sink in Cakespace<br /> | At least one roll<br /> | Supermarkets, DIY stores<br /> |-<br /> | Blue tissue paper<br /> | ?<br /> | A bag of rolls<br /> | Screwfix?<br /> |-<br /> | Badger labels<br /> | Table in corridor, spares in ?<br /> | One box?<br /> | ?<br /> |-<br /> | Whiteboard pens<br /> | Stationery drawers under printers<br /> |<br /> | Staples etc<br /> |-<br /> | microfibre cloths<br /> |<br /> |<br /> |-<br /> | Dymo labeller tape to fit our Dymos<br /> |-<br /> | A4 paper<br /> | Drawers under printers<br /> |-<br /> | Liquid soap<br /> | Cupboards in Cakespace<br /> |-<br /> | Washing-up liquid<br /> | Cupboards in Cakespce<br /> |-<br /> | Gaffer tape<br /> | Louvre bins on wall near back door?<br /> |<br /> | DIY shops<br /> |}</div>

JCGS http://wiki.makespace.org/Stock_list 2015-11-02T13:36:02Z

<p>JCGS: </p> <hr /> <div>{|<br /> |-<br /> ! Item<br /> ! Location<br /> ! Suggested level<br /> ! Available from<br /> ! Item details, part number, etc<br /> |- <br /> | Bin liner bags<br /> | Under sink in Cakespace<br /> | At least one roll<br /> | Supermarkets, DIY stores<br /> |-<br /> | Blue tissue paper<br /> | ?<br /> | A bag of rolls<br /> | Screwfix?<br /> |-<br /> | Badger labels<br /> | Table in corridor, spares in ?<br /> | One box?<br /> | ?<br /> |-<br /> | Whiteboard pens<br /> | Stationery drawers under printers<br /> |<br /> | Staples etc<br /> |}</div>

JCGS http://wiki.makespace.org/Stock_list 2015-11-02T13:35:23Z

<p>JCGS: </p> <hr /> <div>{|<br /> |-<br /> |Item<br /> | Location<br /> | Suggested level<br /> | Available from<br /> |- <br /> | Bin liner bags<br /> | Under sink in Cakespace<br /> | At least one roll<br /> | Supermarkets, DIY stores<br /> |-<br /> | Blue tissue paper<br /> | ?<br /> | A bag of rolls<br /> | Screwfix?<br /> |-<br /> | Badger labels<br /> | Table in corridor, spares in ?<br /> | One box?<br /> | ?<br /> |-<br /> | Whiteboard pens<br /> | Stationery drawers under printers<br /> |<br /> | Staples etc<br /> |}</div>

JCGS http://wiki.makespace.org/Shopping_List 2015-11-02T13:32:59Z

<p>JCGS: </p> <hr /> <div>This is a list of things such as consumables that we think would be useful to buy soon for Makespace! When they are bought they should be deleted from this page. <br /> <br /> * microfibre cloths for cleaning things<br /> * Dymo labeller tape to fit our Dymos<br /> * bin for the craft room<br /> * 'clean' and 'dirty' bags/boxes for tea towels for cakespace<br /> * plentiful pins so every noticeboard has a good set of spares<br /> <br /> See also [[stock list]] for things we should keep in stock.</div>

JCGS http://wiki.makespace.org/Stock_list 2015-11-02T13:32:55Z

<p>JCGS: Initial item</p> <hr /> <div>{|<br /> |-<br /> |Item<br /> | Location<br /> | Suggested level<br /> |- <br /> | Bin liner bags<br /> | Under sink in Cakespace<br /> | At least one roll<br /> |}</div>

JCGS http://wiki.makespace.org/Things_and_stuff 2015-10-27T17:18:39Z

<p>JCGS: /* Main space */</p> <hr /> <div>For larger items, see the [[Equipment]] page.<br /> <br /> This page is to help you to find smaller items, and to help you to put them back in the right place so others can find them. (Use the in-page search in your browser.)<br /> <br /> Some items have extra names in brackets after their usual name; please include all names that people might use to search for a particular item.<br /> <br /> ==The corridor==<br /> <br /> * Badger<br /> * Showcase<br /> * Cupboards including Arduinos, personal laser stock, Family Makers supplies<br /> * Coats<br /> * Lost property<br /> * [[Infrastructure/Member Personal Storage|Personal storage boxes]]<br /> <br /> ==The classroom==<br /> <br /> * [[Classroom/Projector|Projector]]<br /> * [[Classroom/Seating|Stacking chairs]]<br /> * Folding tables<br /> * Non-stacking, non-folding sofas<br /> <br /> ==Main space==<br /> <br /> {|<br /> |+ Main Space<br /> |-<br /> ! South<br /> ! aisle<br /> ! Central<br /> ! aisle<br /> ! North<br /> |-<br /> |<br /> | Windowsill<br /> | Door from corridor<br /> | Windowsill with landline phone<br /> |<br /> |-<br /> | [[Equipment/Glassworking|Glassworking kiln, torch and associated tools]]<br /> [[File:Glassworking.jpg]]<br /> * Kiln<br /> * Torch<br /> | [[Equipment/VacuumFormer|Vacuum Former]]<br /> [[File:Vacuum-former.jpg]]<br /> * Bike repair stuff is usually under this table<br /> |<br /> | Wire and components<br /> * Capacitors<br /> * Resistors<br /> * 74nn ICs (7400 series)<br /> * Wire<br /> | Electronics workbench<br /> * Insulating tape<br /> * Wire strippers<br /> * Pliers<br /> * Needle files<br /> * Screwdrivers<br /> |-<br /> | [[Equipment/Fine_metalwork_bench | Fine metalwork bench]]<br /> [[File:Fine-metalwork-bench.jpg]]<br /> * Dustbuster (small vacuum cleaner)<br /> * Flexible shaft tool<br /> * Scriber<br /> * Centre punch<br /> * Digital calipers (micrometer)<br /> * Flat Stake<br /> * Round triblet (for forming rings and suchlike)<br /> * Planishing Hammer (a polished-surface hammer for surface finishing and work-hardening)<br /> * Rawhide mallet (for hitting things without marking the surface)<br /> * Generic ball-pean hammer (a non-polished hammer for hitting punches etc.)<br /> |<br /> | Table<br /> |<br /> | Electronics workbench<br /> [[File:Electronics-workbenches.jpg]]<br /> On shelves:<br /> * BNC connectors, aerial connectors<br /> * More wire<br /> * Screwdrives, small pliers, etc<br /> * Stripboard<br /> * Solder suckers<br /> * Voltmeters<br /> * Soldering iron tips<br /> * PSUs (Power Supply Units)<br /> * Breadboards<br /> |-<br /> | Laser cutter stock<br /> [[File:Laser-stock.jpg]]<br /> * A grid of squares for measuring how much you've used (for the honesty box) is hung on the left-hand side of this<br /> |<br /> | Table<br /> [[File:White-table.jpg]]<br /> |<br /> | Desk<br /> |-<br /> | Laser cutter computer<br /> [[File:Betsy-desk.jpg]]<br /> |<br /> |<br /> |<br /> | Ultimaker [[Equipment/3D_Printer|3D Printers (FDM)]]<br /> [[File:Ultimaker.jpg]]<br /> |-<br /> | [[Equipment/Laser_Cutter|Laser Cutter]]<br /> [[File:Betsy.jpg]]<br /> | Laser cutter computer<br /> [[File:Jaws-computer.jpg]]<br /> * Swarfega wipes<br /> | [[Equipment/Laser_Cutter|Laser Cutter]]<br /> [[File:Jaws.jpg]]<br /> |<br /> | Makerbot<br /> [[File:Makerbot.jpg]]<br /> * Printer thread<br /> |-<br /> | Formlabs 3D printer<br /> [[File:Formlabs.jpg]]<br /> |<br /> |<br /> |<br /> |<br /> * [[Equipment/CNC_Model_Mill|CNC Model Mill]]<br /> [[File:Roland-mill.jpg]]<br /> * Plates for model mill<br /> |-<br /> | Formlabs desk<br /> [[File:Chargers.jpg]]<br /> * Automatic plant watering system<br /> * AA (etc) battery chargers<br /> |<br /> | Table<br /> |<br /> | Sink area<br /> [[File:Sink-area.jpg]]<br /> * First aid kit<br /> * Eye washout kit<br /> * Torch<br /> * Cleaning cloths<br /> * Liquid soap<br /> * Swarfega<br /> * Fly spray (insecticide)<br /> * Watering can<br /> * Plant food (Baby Bio)<br /> |-<br /> | Desks<br /> [[File:Assorted-desk.jpg]]<br /> |<br /> | Table<br /> |<br /> | [[Equipment/Screenprinting|Screenprinting area]]<br /> [[File:Screen-printing-area.jpg]]<br /> * Screen printing equipment<br /> * Drying racks<br /> |-<br /> | [[Equipment/Plotter|HP 750C A0 Plotter]]<br /> [[File:Plotter.jpg]]<br /> |<br /> | Table<br /> [[File:Big-table.jpg]]<br /> <br /> General hacking area<br /> <br /> * Mains sockets<br /> * USB chargers<br /> |<br /> | Door to workshop<br /> |-<br /> | [[Equipment/Paper Printers|Paper printers]]<br /> [[File:Laser-printers.jpg]]<br /> * Paper<br /> * Stationery including pens, sellotape, whiteboard pens<br /> * CAT-5?<br /> |<br /> | Table<br /> |<br /> | Big shelves<br /> [[File:Deep-shelves.jpg]]<br /> * PPE (goggles, ear protectors, dustmasks)<br /> * PAT testing queue<br /> * Duct tape<br /> * Mains extension reels<br /> * PVA<br /> * Hot air guns (paint strippers)<br /> * Tape measures<br /> |-<br /> | Stair landing to kitchen<br /> | Stairs to kitchen<br /> | Plants and flat storage<br /> * Crimping tools<br /> * Craft knives<br /> * Cable ties<br /> * Rawlplugs<br /> * Watch batteries / button cells<br /> | Fire exit / door to big bins<br /> | Wood offcuts for recycling<br /> |}<br /> <br /> ==The workshop==<br /> <br /> ===West side===<br /> <br /> On the left as you go in:<br /> <br /> * Springs<br /> * Nuts and bolts, machine screws<br /> * Flat pencils<br /> * G-clamps<br /> * Battery charger for cordless tools<br /> * Vacuum cleaner (Henry)<br /> * Fretsaw<br /> * Chemicals cupboard (below worksurface): contains isopropyl alcohol for cleaning<br /> * [[Equipment/MitreSawRage3Db|Mitre Saw - Rage 3]]<br /> * [[Equipment/5704RK|Circular Saw - Makita ]]<br /> * [[Equipment/BandSaw|Band Saw]]<br /> * [[Equipment/CNC_Router|CNC Router]]<br /> <br /> ===Central island===<br /> <br /> * Steel rules, rulers, straight edges<br /> * Set squares<br /> * Spirit level<br /> <br /> In their own boxes under table:<br /> <br /> * Cordless drill<br /> * [[Equipment/5704RK|Circular Saw - Makita ]]<br /> * Jigsaw<br /> <br /> ===East side===<br /> <br /> On the right as you go in:<br /> <br /> * [[Equipment/WarcoMill|Mill - Warco ]]<br /> * [[Equipment/Lathe|Lathe - Myford]]<br /> * [[Equipment/Drill_Presses|Drill Presses]]<br /> * [[Equipment/Grinder|Grinder]]<br /> * Clamps<br /> * Pop rivets and rivet tool<br /> * Small nuts and bolts<br /> * Drill bits<br /> * [[Equipment/WoodLathe|Woodworking Lathe]]<br /> <br /> In storage bins:<br /> * Files<br /> * Screwdrivers<br /> * Allen keys (Hex keys)<br /> * Torx keys (Star screwdrivers)<br /> <br /> Hand tools on shadowboard:<br /> * Hammers<br /> * Hacksaws<br /> * Pliers<br /> <br /> ==The treasure trove==<br /> <br /> === Wall nearest door ===<br /> <br /> * Old disk drives including floppy drives<br /> <br /> === Near side of central shelves ===<br /> <br /> * Old audio / video stuff you could rebuild for something<br /> * Personal supplies of flat stuff that is too big for elsewhere<br /> * Old &quot;tower&quot; computer cases<br /> <br /> === Far side of central shelves ===<br /> <br /> * Electrical cables selection<br /> * Bits of cameras<br /> * Computer (ATX?) PSUs<br /> <br /> === Far shelves ===<br /> <br /> * Mains power supplies of many kinds<br /> * Fans<br /> * Capacitors<br /> * Resistors<br /> <br /> === Unclassified location ===<br /> <br /> * Various electrical connections and fittings<br /> * Multi-way mains extensions<br /> * Nabaztags (electric rabbits)<br /> * Just about anything for repurposing<br /> * Sledgehammer (broken handle, belongs to Visventis)<br /> <br /> ==The kitchen (Cakespace)==<br /> <br /> * Kettle<br /> * Oven<br /> * Microwave<br /> * Drinks<br /> * Snacks<br /> * Liquid soap<br /> * Cleaning materials<br /> * Bin bags<br /> <br /> ==Craft Room==<br /> <br /> * Vinyl cutter<br /> * Vinyl cutter stock<br /> * Eggbot<br /> * Knitting machine<br /> * Sewing machines<br /> * Thread<br /> * T-shirt press<br /> * Crafting table<br /> <br /> ==Unknown location==<br /> <br /> If you know where the things in this section are, please move their names to the appropriate section.</div>

JCGS http://wiki.makespace.org/Things_and_stuff 2015-10-24T22:31:38Z

<p>JCGS: /* Main space */</p> <hr /> <div>For larger items, see the [[Equipment]] page.<br /> <br /> This page is to help you to find smaller items, and to help you to put them back in the right place so others can find them. (Use the in-page search in your browser.)<br /> <br /> Some items have extra names in brackets after their usual name; please include all names that people might use to search for a particular item.<br /> <br /> ==The corridor==<br /> <br /> * Badger<br /> * Showcase<br /> * Cupboards including Arduinos, personal laser stock, Family Makers supplies<br /> * Coats<br /> * Lost property<br /> * [[Infrastructure/Member Personal Storage|Personal storage boxes]]<br /> <br /> ==The classroom==<br /> <br /> * [[Classroom/Projector|Projector]]<br /> * [[Classroom/Seating|Stacking chairs]]<br /> * Folding tables<br /> * Non-stacking, non-folding sofas<br /> <br /> ==Main space==<br /> <br /> {|<br /> |+ Main Space<br /> |-<br /> ! South<br /> ! aisle<br /> ! Central<br /> ! aisle<br /> ! North<br /> |-<br /> |<br /> | Windowsill<br /> | Door from corridor<br /> | Windowsill with landline phone<br /> |<br /> |-<br /> | [[Equipment/Glassworking|Glassworking kiln, torch and associated tools]]<br /> [[File:Glassworking.jpg]]<br /> * Kiln<br /> * Torch<br /> | [[Equipment/VacuumFormer|Vacuum Former]]<br /> [[File:Vacuum-former.jpg]]<br /> |<br /> | Wire and components<br /> * Capacitors<br /> * Resistors<br /> * 74nn ICs (7400 series)<br /> * Wire<br /> | Electronics workbench<br /> * Insulating tape<br /> * Wire strippers<br /> * Pliers<br /> * Needle files<br /> * Screwdrivers<br /> |-<br /> | [[Equipment/Fine_metalwork_bench | Fine metalwork bench]]<br /> [[File:Fine-metalwork-bench.jpg]]<br /> * Dustbuster (small vacuum cleaner)<br /> * Flexible shaft tool<br /> * Scriber<br /> * Centre punch<br /> * Digital calipers (micrometer)<br /> * Flat Stake<br /> * Round triblet (for forming rings and suchlike)<br /> * Planishing Hammer (a polished-surface hammer for surface finishing and work-hardening)<br /> * Rawhide mallet (for hitting things without marking the surface)<br /> * Generic ball-pean hammer (a non-polished hammer for hitting punches etc.)<br /> |<br /> | Table<br /> |<br /> | Electronics workbench<br /> [[File:Electronics-workbenches.jpg]]<br /> On shelves:<br /> * BNC connectors, aerial connectors<br /> * More wire<br /> * Screwdrives, small pliers, etc<br /> * Stripboard<br /> * Solder suckers<br /> * Voltmeters<br /> * Soldering iron tips<br /> * PSUs (Power Supply Units)<br /> * Breadboards<br /> |-<br /> | Laser cutter stock<br /> [[File:Laser-stock.jpg]]<br /> |<br /> | Table<br /> [[File:White-table.jpg]]<br /> |<br /> | Desk<br /> |-<br /> | Laser cutter computer<br /> [[File:Betsy-desk.jpg]]<br /> |<br /> |<br /> |<br /> | Ultimaker [[Equipment/3D_Printer|3D Printers (FDM)]]<br /> [[File:Ultimaker.jpg]]<br /> |-<br /> | [[Equipment/Laser_Cutter|Laser Cutter]]<br /> [[File:Betsy.jpg]]<br /> | Laser cutter computer<br /> [[File:Jaws-computer.jpg]]<br /> * Swarfega wipes<br /> | [[Equipment/Laser_Cutter|Laser Cutter]]<br /> [[File:Jaws.jpg]]<br /> |<br /> | Makerbot<br /> [[File:Makerbot.jpg]]<br /> * Printer thread<br /> |-<br /> | Formlabs 3D printer<br /> [[File:Formlabs.jpg]]<br /> |<br /> |<br /> |<br /> |<br /> * [[Equipment/CNC_Model_Mill|CNC Model Mill]]<br /> [[File:Roland-mill.jpg]]<br /> * Plates for model mill<br /> |-<br /> | Formlabs desk<br /> [[File:Chargers.jpg]]<br /> * Automatic plant watering system<br /> * AA (etc) battery chargers<br /> |<br /> | Table<br /> |<br /> | Sink area<br /> [[File:Sink-area.jpg]]<br /> * First aid kit<br /> * Eye washout kit<br /> * Torch<br /> * Cleaning cloths<br /> * Liquid soap<br /> * Swarfega<br /> * Fly spray (insecticide)<br /> * Watering can<br /> * Plant food (Baby Bio)<br /> |-<br /> | Desks<br /> [[File:Assorted-desk.jpg]]<br /> |<br /> | Table<br /> |<br /> | [[Equipment/Screenprinting|Screenprinting area]]<br /> [[File:Screen-printing-area.jpg]]<br /> * Screen printing equipment<br /> * Drying racks<br /> |-<br /> | [[Equipment/Plotter|HP 750C A0 Plotter]]<br /> [[File:Plotter.jpg]]<br /> |<br /> | Table<br /> [[File:Big-table.jpg]]<br /> <br /> General hacking area<br /> <br /> * Mains sockets<br /> * USB chargers<br /> |<br /> | Door to workshop<br /> |-<br /> | [[Equipment/Paper Printers|Paper printers]]<br /> [[File:Laser-printers.jpg]]<br /> * Paper<br /> * Stationery including pens, sellotape, whiteboard pens<br /> * CAT-5?<br /> |<br /> | Table<br /> |<br /> | Big shelves<br /> [[File:Deep-shelves.jpg]]<br /> * PPE (goggles, ear protectors, dustmasks)<br /> * PAT testing queue<br /> * Duct tape<br /> * Mains extension reels<br /> * PVA<br /> * Hot air guns (paint strippers)<br /> * Tape measures<br /> |-<br /> | Stair landing to kitchen<br /> | Stairs to kitchen<br /> | Plants and flat storage<br /> * Crimping tools<br /> * Craft knives<br /> * Cable ties<br /> * Rawlplugs<br /> * Watch batteries / button cells<br /> | Fire exit / door to big bins<br /> | Wood offcuts for recycling<br /> |}<br /> <br /> ==The workshop==<br /> <br /> ===West side===<br /> <br /> On the left as you go in:<br /> <br /> * Springs<br /> * Nuts and bolts, machine screws<br /> * Flat pencils<br /> * G-clamps<br /> * Battery charger for cordless tools<br /> * Vacuum cleaner (Henry)<br /> * Fretsaw<br /> * Chemicals cupboard (below worksurface): contains isopropyl alcohol for cleaning<br /> * [[Equipment/MitreSawRage3Db|Mitre Saw - Rage 3]]<br /> * [[Equipment/5704RK|Circular Saw - Makita ]]<br /> * [[Equipment/BandSaw|Band Saw]]<br /> * [[Equipment/CNC_Router|CNC Router]]<br /> <br /> ===Central island===<br /> <br /> * Steel rules, rulers, straight edges<br /> * Set squares<br /> * Spirit level<br /> <br /> In their own boxes under table:<br /> <br /> * Cordless drill<br /> * [[Equipment/5704RK|Circular Saw - Makita ]]<br /> * Jigsaw<br /> <br /> ===East side===<br /> <br /> On the right as you go in:<br /> <br /> * [[Equipment/WarcoMill|Mill - Warco ]]<br /> * [[Equipment/Lathe|Lathe - Myford]]<br /> * [[Equipment/Drill_Presses|Drill Presses]]<br /> * [[Equipment/Grinder|Grinder]]<br /> * Clamps<br /> * Pop rivets and rivet tool<br /> * Small nuts and bolts<br /> * Drill bits<br /> * [[Equipment/WoodLathe|Woodworking Lathe]]<br /> <br /> In storage bins:<br /> * Files<br /> * Screwdrivers<br /> * Allen keys (Hex keys)<br /> * Torx keys (Star screwdrivers)<br /> <br /> Hand tools on shadowboard:<br /> * Hammers<br /> * Hacksaws<br /> * Pliers<br /> <br /> ==The treasure trove==<br /> <br /> === Wall nearest door ===<br /> <br /> * Old disk drives including floppy drives<br /> <br /> === Near side of central shelves ===<br /> <br /> * Old audio / video stuff you could rebuild for something<br /> * Personal supplies of flat stuff that is too big for elsewhere<br /> * Old &quot;tower&quot; computer cases<br /> <br /> === Far side of central shelves ===<br /> <br /> * Electrical cables selection<br /> * Bits of cameras<br /> * Computer (ATX?) PSUs<br /> <br /> === Far shelves ===<br /> <br /> * Mains power supplies of many kinds<br /> * Fans<br /> * Capacitors<br /> * Resistors<br /> <br /> === Unclassified location ===<br /> <br /> * Various electrical connections and fittings<br /> * Multi-way mains extensions<br /> * Nabaztags (electric rabbits)<br /> * Just about anything for repurposing<br /> * Sledgehammer (broken handle, belongs to Visventis)<br /> <br /> ==The kitchen (Cakespace)==<br /> <br /> * Kettle<br /> * Oven<br /> * Microwave<br /> * Drinks<br /> * Snacks<br /> * Liquid soap<br /> * Cleaning materials<br /> * Bin bags<br /> <br /> ==Craft Room==<br /> <br /> * Vinyl cutter<br /> * Vinyl cutter stock<br /> * Eggbot<br /> * Knitting machine<br /> * Sewing machines<br /> * Thread<br /> * T-shirt press<br /> * Crafting table<br /> <br /> ==Unknown location==<br /> <br /> If you know where the things in this section are, please move their names to the appropriate section.</div>

JCGS http://wiki.makespace.org/Things_and_stuff 2015-10-24T22:29:58Z

<p>JCGS: /* Craft Room */</p> <hr /> <div>For larger items, see the [[Equipment]] page.<br /> <br /> This page is to help you to find smaller items, and to help you to put them back in the right place so others can find them. (Use the in-page search in your browser.)<br /> <br /> Some items have extra names in brackets after their usual name; please include all names that people might use to search for a particular item.<br /> <br /> ==The corridor==<br /> <br /> * Badger<br /> * Showcase<br /> * Cupboards including Arduinos, personal laser stock, Family Makers supplies<br /> * Coats<br /> * Lost property<br /> * [[Infrastructure/Member Personal Storage|Personal storage boxes]]<br /> <br /> ==The classroom==<br /> <br /> * [[Classroom/Projector|Projector]]<br /> * [[Classroom/Seating|Stacking chairs]]<br /> * Folding tables<br /> * Non-stacking, non-folding sofas<br /> <br /> ==Main space==<br /> <br /> {|<br /> |+ Main Space<br /> |-<br /> ! South<br /> ! aisle<br /> ! Central<br /> ! aisle<br /> ! North<br /> |-<br /> |<br /> | Windowsill<br /> | Door from corridor<br /> | Windowsill with landline phone<br /> |<br /> |-<br /> | [[Equipment/Glassworking|Glassworking kiln, torch and associated tools]]<br /> [[File:Glassworking.jpg]]<br /> * Kiln<br /> * Torch<br /> | [[Equipment/VacuumFormer|Vacuum Former]]<br /> [[File:Vacuum-former.jpg]]<br /> |<br /> | Wire and components<br /> * Capacitors<br /> * Resistors<br /> * 74nn ICs (7400 series)<br /> * Wire<br /> | Electronics workbench<br /> * Insulating tape<br /> * Wire strippers<br /> * Pliers<br /> * Needle files<br /> * Screwdrivers<br /> |-<br /> | [[Equipment/Fine_metalwork_bench | Fine metalwork bench]]<br /> [[File:Fine-metalwork-bench.jpg]]<br /> * Dustbuster (small vacuum cleaner)<br /> * Flexible shaft tool<br /> * Scriber<br /> * Centre punch<br /> * Digital calipers (micrometer)<br /> * Flat Stake<br /> * Round triblet (for forming rings and suchlike)<br /> * Planishing Hammer (a polished-surface hammer for surface finishing and work-hardening)<br /> * Rawhide mallet (for hitting things without marking the surface)<br /> * Generic ball-pean hammer (a non-polished hammer for hitting punches etc.)<br /> |<br /> | Table<br /> |<br /> | Electronics workbench<br /> [[File:Electronics-workbenches.jpg]]<br /> On shelves:<br /> * BNC connectors, aerial connectors<br /> * More wire<br /> * Screwdrives, small pliers, etc<br /> * Stripboard<br /> * Solder suckers<br /> * Voltmeters<br /> * Soldering iron tips<br /> * PSUs (Power Supply Units)<br /> * Breadboards<br /> |-<br /> | Laser cutter stock<br /> [[File:Laser-stock.jpg]]<br /> |<br /> | Table<br /> [[File:White-table.jpg]]<br /> |<br /> | Desk<br /> |-<br /> | Laser cutter computer<br /> [[File:Betsy-desk.jpg]]<br /> |<br /> |<br /> |<br /> | Ultimaker [[Equipment/3D_Printer|3D Printers (FDM)]]<br /> [[File:Ultimaker.jpg]]<br /> |-<br /> | [[Equipment/Laser_Cutter|Laser Cutter]]<br /> [[File:Betsy.jpg]]<br /> | Laser cutter computer<br /> [[File:Jaws-computer.jpg]]<br /> * Swarfega wipes<br /> | [[Equipment/Laser_Cutter|Laser Cutter]]<br /> [[File:Jaws.jpg]]<br /> |<br /> | Makerbot<br /> [[File:Makerbot.jpg]]<br /> * Printer thread<br /> |-<br /> | Formlabs 3D printer<br /> [[File:Formlabs.jpg]]<br /> |<br /> |<br /> |<br /> |<br /> * [[Equipment/CNC_Model_Mill|CNC Model Mill]]<br /> [[File:Roland-mill.jpg]]<br /> * Plates for model mill<br /> |-<br /> | Formlabs desk<br /> [[File:Chargers.jpg]]<br /> * Automatic plant watering system<br /> * AA (etc) battery chargers<br /> |<br /> | Table<br /> |<br /> | Sink area<br /> [[File:Sink-area.jpg]]<br /> * First aid kit<br /> * Eye washout kit<br /> * Torch<br /> * Cleaning cloths<br /> * Liquid soap<br /> * Swarfega<br /> * Fly spray (insecticide)<br /> * Watering can<br /> * Plant food (Baby Bio)<br /> |-<br /> | Desks<br /> [[File:Assorted-desk.jpg]]<br /> |<br /> | Table<br /> |<br /> | [[Equipment/Screenprinting|Screenprinting area]]<br /> [[File:Screen-printing-area.jpg]]<br /> * Screen printing equipment<br /> * Drying racks<br /> |-<br /> | [[Equipment/Plotter|HP 750C A0 Plotter]]<br /> [[File:Plotter.jpg]]<br /> |<br /> | Table<br /> [[File:Big-table.jpg]]<br /> General hacking area<br /> * Mains sockets<br /> * USB chargers<br /> |<br /> | Door to workshop<br /> |-<br /> | [[Equipment/Paper Printers|Paper printers]]<br /> [[File:Laser-printers.jpg]]<br /> * Paper<br /> * Stationery including pens, sellotape, whiteboard pens<br /> * CAT-5?<br /> |<br /> | Table<br /> |<br /> | Big shelves<br /> [[File:Deep-shelves.jpg]]<br /> * PPE (goggles, ear protectors, dustmasks)<br /> * PAT testing queue<br /> * Duct tape<br /> * Mains extension reels<br /> * PVA<br /> * Hot air guns (paint strippers)<br /> * Tape measures<br /> |-<br /> | Stair landing to kitchen<br /> | Stairs to kitchen<br /> | Plants and flat storage<br /> * Crimping tools<br /> * Craft knives<br /> * Cable ties<br /> * Rawlplugs<br /> * Watch batteries / button cells<br /> | Fire exit / door to big bins<br /> | Wood offcuts for recycling<br /> |}<br /> <br /> ==The workshop==<br /> <br /> ===West side===<br /> <br /> On the left as you go in:<br /> <br /> * Springs<br /> * Nuts and bolts, machine screws<br /> * Flat pencils<br /> * G-clamps<br /> * Battery charger for cordless tools<br /> * Vacuum cleaner (Henry)<br /> * Fretsaw<br /> * Chemicals cupboard (below worksurface): contains isopropyl alcohol for cleaning<br /> * [[Equipment/MitreSawRage3Db|Mitre Saw - Rage 3]]<br /> * [[Equipment/5704RK|Circular Saw - Makita ]]<br /> * [[Equipment/BandSaw|Band Saw]]<br /> * [[Equipment/CNC_Router|CNC Router]]<br /> <br /> ===Central island===<br /> <br /> * Steel rules, rulers, straight edges<br /> * Set squares<br /> * Spirit level<br /> <br /> In their own boxes under table:<br /> <br /> * Cordless drill<br /> * [[Equipment/5704RK|Circular Saw - Makita ]]<br /> * Jigsaw<br /> <br /> ===East side===<br /> <br /> On the right as you go in:<br /> <br /> * [[Equipment/WarcoMill|Mill - Warco ]]<br /> * [[Equipment/Lathe|Lathe - Myford]]<br /> * [[Equipment/Drill_Presses|Drill Presses]]<br /> * [[Equipment/Grinder|Grinder]]<br /> * Clamps<br /> * Pop rivets and rivet tool<br /> * Small nuts and bolts<br /> * Drill bits<br /> * [[Equipment/WoodLathe|Woodworking Lathe]]<br /> <br /> In storage bins:<br /> * Files<br /> * Screwdrivers<br /> * Allen keys (Hex keys)<br /> * Torx keys (Star screwdrivers)<br /> <br /> Hand tools on shadowboard:<br /> * Hammers<br /> * Hacksaws<br /> * Pliers<br /> <br /> ==The treasure trove==<br /> <br /> === Wall nearest door ===<br /> <br /> * Old disk drives including floppy drives<br /> <br /> === Near side of central shelves ===<br /> <br /> * Old audio / video stuff you could rebuild for something<br /> * Personal supplies of flat stuff that is too big for elsewhere<br /> * Old &quot;tower&quot; computer cases<br /> <br /> === Far side of central shelves ===<br /> <br /> * Electrical cables selection<br /> * Bits of cameras<br /> * Computer (ATX?) PSUs<br /> <br /> === Far shelves ===<br /> <br /> * Mains power supplies of many kinds<br /> * Fans<br /> * Capacitors<br /> * Resistors<br /> <br /> === Unclassified location ===<br /> <br /> * Various electrical connections and fittings<br /> * Multi-way mains extensions<br /> * Nabaztags (electric rabbits)<br /> * Just about anything for repurposing<br /> * Sledgehammer (broken handle, belongs to Visventis)<br /> <br /> ==The kitchen (Cakespace)==<br /> <br /> * Kettle<br /> * Oven<br /> * Microwave<br /> * Drinks<br /> * Snacks<br /> * Liquid soap<br /> * Cleaning materials<br /> * Bin bags<br /> <br /> ==Craft Room==<br /> <br /> * Vinyl cutter<br /> * Vinyl cutter stock<br /> * Eggbot<br /> * Knitting machine<br /> * Sewing machines<br /> * Thread<br /> * T-shirt press<br /> * Crafting table<br /> <br /> ==Unknown location==<br /> <br /> If you know where the things in this section are, please move their names to the appropriate section.</div>

JCGS http://wiki.makespace.org/Things_and_stuff 2015-10-24T22:29:33Z

<p>JCGS: /* The kitchen (Cakespace) */</p> <hr /> <div>For larger items, see the [[Equipment]] page.<br /> <br /> This page is to help you to find smaller items, and to help you to put them back in the right place so others can find them. (Use the in-page search in your browser.)<br /> <br /> Some items have extra names in brackets after their usual name; please include all names that people might use to search for a particular item.<br /> <br /> ==The corridor==<br /> <br /> * Badger<br /> * Showcase<br /> * Cupboards including Arduinos, personal laser stock, Family Makers supplies<br /> * Coats<br /> * Lost property<br /> * [[Infrastructure/Member Personal Storage|Personal storage boxes]]<br /> <br /> ==The classroom==<br /> <br /> * [[Classroom/Projector|Projector]]<br /> * [[Classroom/Seating|Stacking chairs]]<br /> * Folding tables<br /> * Non-stacking, non-folding sofas<br /> <br /> ==Main space==<br /> <br /> {|<br /> |+ Main Space<br /> |-<br /> ! South<br /> ! aisle<br /> ! Central<br /> ! aisle<br /> ! North<br /> |-<br /> |<br /> | Windowsill<br /> | Door from corridor<br /> | Windowsill with landline phone<br /> |<br /> |-<br /> | [[Equipment/Glassworking|Glassworking kiln, torch and associated tools]]<br /> [[File:Glassworking.jpg]]<br /> * Kiln<br /> * Torch<br /> | [[Equipment/VacuumFormer|Vacuum Former]]<br /> [[File:Vacuum-former.jpg]]<br /> |<br /> | Wire and components<br /> * Capacitors<br /> * Resistors<br /> * 74nn ICs (7400 series)<br /> * Wire<br /> | Electronics workbench<br /> * Insulating tape<br /> * Wire strippers<br /> * Pliers<br /> * Needle files<br /> * Screwdrivers<br /> |-<br /> | [[Equipment/Fine_metalwork_bench | Fine metalwork bench]]<br /> [[File:Fine-metalwork-bench.jpg]]<br /> * Dustbuster (small vacuum cleaner)<br /> * Flexible shaft tool<br /> * Scriber<br /> * Centre punch<br /> * Digital calipers (micrometer)<br /> * Flat Stake<br /> * Round triblet (for forming rings and suchlike)<br /> * Planishing Hammer (a polished-surface hammer for surface finishing and work-hardening)<br /> * Rawhide mallet (for hitting things without marking the surface)<br /> * Generic ball-pean hammer (a non-polished hammer for hitting punches etc.)<br /> |<br /> | Table<br /> |<br /> | Electronics workbench<br /> [[File:Electronics-workbenches.jpg]]<br /> On shelves:<br /> * BNC connectors, aerial connectors<br /> * More wire<br /> * Screwdrives, small pliers, etc<br /> * Stripboard<br /> * Solder suckers<br /> * Voltmeters<br /> * Soldering iron tips<br /> * PSUs (Power Supply Units)<br /> * Breadboards<br /> |-<br /> | Laser cutter stock<br /> [[File:Laser-stock.jpg]]<br /> |<br /> | Table<br /> [[File:White-table.jpg]]<br /> |<br /> | Desk<br /> |-<br /> | Laser cutter computer<br /> [[File:Betsy-desk.jpg]]<br /> |<br /> |<br /> |<br /> | Ultimaker [[Equipment/3D_Printer|3D Printers (FDM)]]<br /> [[File:Ultimaker.jpg]]<br /> |-<br /> | [[Equipment/Laser_Cutter|Laser Cutter]]<br /> [[File:Betsy.jpg]]<br /> | Laser cutter computer<br /> [[File:Jaws-computer.jpg]]<br /> * Swarfega wipes<br /> | [[Equipment/Laser_Cutter|Laser Cutter]]<br /> [[File:Jaws.jpg]]<br /> |<br /> | Makerbot<br /> [[File:Makerbot.jpg]]<br /> * Printer thread<br /> |-<br /> | Formlabs 3D printer<br /> [[File:Formlabs.jpg]]<br /> |<br /> |<br /> |<br /> |<br /> * [[Equipment/CNC_Model_Mill|CNC Model Mill]]<br /> [[File:Roland-mill.jpg]]<br /> * Plates for model mill<br /> |-<br /> | Formlabs desk<br /> [[File:Chargers.jpg]]<br /> * Automatic plant watering system<br /> * AA (etc) battery chargers<br /> |<br /> | Table<br /> |<br /> | Sink area<br /> [[File:Sink-area.jpg]]<br /> * First aid kit<br /> * Eye washout kit<br /> * Torch<br /> * Cleaning cloths<br /> * Liquid soap<br /> * Swarfega<br /> * Fly spray (insecticide)<br /> * Watering can<br /> * Plant food (Baby Bio)<br /> |-<br /> | Desks<br /> [[File:Assorted-desk.jpg]]<br /> |<br /> | Table<br /> |<br /> | [[Equipment/Screenprinting|Screenprinting area]]<br /> [[File:Screen-printing-area.jpg]]<br /> * Screen printing equipment<br /> * Drying racks<br /> |-<br /> | [[Equipment/Plotter|HP 750C A0 Plotter]]<br /> [[File:Plotter.jpg]]<br /> |<br /> | Table<br /> [[File:Big-table.jpg]]<br /> General hacking area<br /> * Mains sockets<br /> * USB chargers<br /> |<br /> | Door to workshop<br /> |-<br /> | [[Equipment/Paper Printers|Paper printers]]<br /> [[File:Laser-printers.jpg]]<br /> * Paper<br /> * Stationery including pens, sellotape, whiteboard pens<br /> * CAT-5?<br /> |<br /> | Table<br /> |<br /> | Big shelves<br /> [[File:Deep-shelves.jpg]]<br /> * PPE (goggles, ear protectors, dustmasks)<br /> * PAT testing queue<br /> * Duct tape<br /> * Mains extension reels<br /> * PVA<br /> * Hot air guns (paint strippers)<br /> * Tape measures<br /> |-<br /> | Stair landing to kitchen<br /> | Stairs to kitchen<br /> | Plants and flat storage<br /> * Crimping tools<br /> * Craft knives<br /> * Cable ties<br /> * Rawlplugs<br /> * Watch batteries / button cells<br /> | Fire exit / door to big bins<br /> | Wood offcuts for recycling<br /> |}<br /> <br /> ==The workshop==<br /> <br /> ===West side===<br /> <br /> On the left as you go in:<br /> <br /> * Springs<br /> * Nuts and bolts, machine screws<br /> * Flat pencils<br /> * G-clamps<br /> * Battery charger for cordless tools<br /> * Vacuum cleaner (Henry)<br /> * Fretsaw<br /> * Chemicals cupboard (below worksurface): contains isopropyl alcohol for cleaning<br /> * [[Equipment/MitreSawRage3Db|Mitre Saw - Rage 3]]<br /> * [[Equipment/5704RK|Circular Saw - Makita ]]<br /> * [[Equipment/BandSaw|Band Saw]]<br /> * [[Equipment/CNC_Router|CNC Router]]<br /> <br /> ===Central island===<br /> <br /> * Steel rules, rulers, straight edges<br /> * Set squares<br /> * Spirit level<br /> <br /> In their own boxes under table:<br /> <br /> * Cordless drill<br /> * [[Equipment/5704RK|Circular Saw - Makita ]]<br /> * Jigsaw<br /> <br /> ===East side===<br /> <br /> On the right as you go in:<br /> <br /> * [[Equipment/WarcoMill|Mill - Warco ]]<br /> * [[Equipment/Lathe|Lathe - Myford]]<br /> * [[Equipment/Drill_Presses|Drill Presses]]<br /> * [[Equipment/Grinder|Grinder]]<br /> * Clamps<br /> * Pop rivets and rivet tool<br /> * Small nuts and bolts<br /> * Drill bits<br /> * [[Equipment/WoodLathe|Woodworking Lathe]]<br /> <br /> In storage bins:<br /> * Files<br /> * Screwdrivers<br /> * Allen keys (Hex keys)<br /> * Torx keys (Star screwdrivers)<br /> <br /> Hand tools on shadowboard:<br /> * Hammers<br /> * Hacksaws<br /> * Pliers<br /> <br /> ==The treasure trove==<br /> <br /> === Wall nearest door ===<br /> <br /> * Old disk drives including floppy drives<br /> <br /> === Near side of central shelves ===<br /> <br /> * Old audio / video stuff you could rebuild for something<br /> * Personal supplies of flat stuff that is too big for elsewhere<br /> * Old &quot;tower&quot; computer cases<br /> <br /> === Far side of central shelves ===<br /> <br /> * Electrical cables selection<br /> * Bits of cameras<br /> * Computer (ATX?) PSUs<br /> <br /> === Far shelves ===<br /> <br /> * Mains power supplies of many kinds<br /> * Fans<br /> * Capacitors<br /> * Resistors<br /> <br /> === Unclassified location ===<br /> <br /> * Various electrical connections and fittings<br /> * Multi-way mains extensions<br /> * Nabaztags (electric rabbits)<br /> * Just about anything for repurposing<br /> * Sledgehammer (broken handle, belongs to Visventis)<br /> <br /> ==The kitchen (Cakespace)==<br /> <br /> * Kettle<br /> * Oven<br /> * Microwave<br /> * Drinks<br /> * Snacks<br /> * Liquid soap<br /> * Cleaning materials<br /> * Bin bags<br /> <br /> ==Craft Room==<br /> <br /> * Vinyl cutter<br /> * Vinyl cutter stock<br /> * Eggbot<br /> * Knitting machine<br /> * Sewing machines<br /> * T-shirt press<br /> * Crafting table<br /> <br /> ==Unknown location==<br /> <br /> If you know where the things in this section are, please move their names to the appropriate section.</div>

JCGS http://wiki.makespace.org/Things_and_stuff 2015-10-24T22:29:00Z

<p>JCGS: /* The treasure trove */</p> <hr /> <div>For larger items, see the [[Equipment]] page.<br /> <br /> This page is to help you to find smaller items, and to help you to put them back in the right place so others can find them. (Use the in-page search in your browser.)<br /> <br /> Some items have extra names in brackets after their usual name; please include all names that people might use to search for a particular item.<br /> <br /> ==The corridor==<br /> <br /> * Badger<br /> * Showcase<br /> * Cupboards including Arduinos, personal laser stock, Family Makers supplies<br /> * Coats<br /> * Lost property<br /> * [[Infrastructure/Member Personal Storage|Personal storage boxes]]<br /> <br /> ==The classroom==<br /> <br /> * [[Classroom/Projector|Projector]]<br /> * [[Classroom/Seating|Stacking chairs]]<br /> * Folding tables<br /> * Non-stacking, non-folding sofas<br /> <br /> ==Main space==<br /> <br /> {|<br /> |+ Main Space<br /> |-<br /> ! South<br /> ! aisle<br /> ! Central<br /> ! aisle<br /> ! North<br /> |-<br /> |<br /> | Windowsill<br /> | Door from corridor<br /> | Windowsill with landline phone<br /> |<br /> |-<br /> | [[Equipment/Glassworking|Glassworking kiln, torch and associated tools]]<br /> [[File:Glassworking.jpg]]<br /> * Kiln<br /> * Torch<br /> | [[Equipment/VacuumFormer|Vacuum Former]]<br /> [[File:Vacuum-former.jpg]]<br /> |<br /> | Wire and components<br /> * Capacitors<br /> * Resistors<br /> * 74nn ICs (7400 series)<br /> * Wire<br /> | Electronics workbench<br /> * Insulating tape<br /> * Wire strippers<br /> * Pliers<br /> * Needle files<br /> * Screwdrivers<br /> |-<br /> | [[Equipment/Fine_metalwork_bench | Fine metalwork bench]]<br /> [[File:Fine-metalwork-bench.jpg]]<br /> * Dustbuster (small vacuum cleaner)<br /> * Flexible shaft tool<br /> * Scriber<br /> * Centre punch<br /> * Digital calipers (micrometer)<br /> * Flat Stake<br /> * Round triblet (for forming rings and suchlike)<br /> * Planishing Hammer (a polished-surface hammer for surface finishing and work-hardening)<br /> * Rawhide mallet (for hitting things without marking the surface)<br /> * Generic ball-pean hammer (a non-polished hammer for hitting punches etc.)<br /> |<br /> | Table<br /> |<br /> | Electronics workbench<br /> [[File:Electronics-workbenches.jpg]]<br /> On shelves:<br /> * BNC connectors, aerial connectors<br /> * More wire<br /> * Screwdrives, small pliers, etc<br /> * Stripboard<br /> * Solder suckers<br /> * Voltmeters<br /> * Soldering iron tips<br /> * PSUs (Power Supply Units)<br /> * Breadboards<br /> |-<br /> | Laser cutter stock<br /> [[File:Laser-stock.jpg]]<br /> |<br /> | Table<br /> [[File:White-table.jpg]]<br /> |<br /> | Desk<br /> |-<br /> | Laser cutter computer<br /> [[File:Betsy-desk.jpg]]<br /> |<br /> |<br /> |<br /> | Ultimaker [[Equipment/3D_Printer|3D Printers (FDM)]]<br /> [[File:Ultimaker.jpg]]<br /> |-<br /> | [[Equipment/Laser_Cutter|Laser Cutter]]<br /> [[File:Betsy.jpg]]<br /> | Laser cutter computer<br /> [[File:Jaws-computer.jpg]]<br /> * Swarfega wipes<br /> | [[Equipment/Laser_Cutter|Laser Cutter]]<br /> [[File:Jaws.jpg]]<br /> |<br /> | Makerbot<br /> [[File:Makerbot.jpg]]<br /> * Printer thread<br /> |-<br /> | Formlabs 3D printer<br /> [[File:Formlabs.jpg]]<br /> |<br /> |<br /> |<br /> |<br /> * [[Equipment/CNC_Model_Mill|CNC Model Mill]]<br /> [[File:Roland-mill.jpg]]<br /> * Plates for model mill<br /> |-<br /> | Formlabs desk<br /> [[File:Chargers.jpg]]<br /> * Automatic plant watering system<br /> * AA (etc) battery chargers<br /> |<br /> | Table<br /> |<br /> | Sink area<br /> [[File:Sink-area.jpg]]<br /> * First aid kit<br /> * Eye washout kit<br /> * Torch<br /> * Cleaning cloths<br /> * Liquid soap<br /> * Swarfega<br /> * Fly spray (insecticide)<br /> * Watering can<br /> * Plant food (Baby Bio)<br /> |-<br /> | Desks<br /> [[File:Assorted-desk.jpg]]<br /> |<br /> | Table<br /> |<br /> | [[Equipment/Screenprinting|Screenprinting area]]<br /> [[File:Screen-printing-area.jpg]]<br /> * Screen printing equipment<br /> * Drying racks<br /> |-<br /> | [[Equipment/Plotter|HP 750C A0 Plotter]]<br /> [[File:Plotter.jpg]]<br /> |<br /> | Table<br /> [[File:Big-table.jpg]]<br /> General hacking area<br /> * Mains sockets<br /> * USB chargers<br /> |<br /> | Door to workshop<br /> |-<br /> | [[Equipment/Paper Printers|Paper printers]]<br /> [[File:Laser-printers.jpg]]<br /> * Paper<br /> * Stationery including pens, sellotape, whiteboard pens<br /> * CAT-5?<br /> |<br /> | Table<br /> |<br /> | Big shelves<br /> [[File:Deep-shelves.jpg]]<br /> * PPE (goggles, ear protectors, dustmasks)<br /> * PAT testing queue<br /> * Duct tape<br /> * Mains extension reels<br /> * PVA<br /> * Hot air guns (paint strippers)<br /> * Tape measures<br /> |-<br /> | Stair landing to kitchen<br /> | Stairs to kitchen<br /> | Plants and flat storage<br /> * Crimping tools<br /> * Craft knives<br /> * Cable ties<br /> * Rawlplugs<br /> * Watch batteries / button cells<br /> | Fire exit / door to big bins<br /> | Wood offcuts for recycling<br /> |}<br /> <br /> ==The workshop==<br /> <br /> ===West side===<br /> <br /> On the left as you go in:<br /> <br /> * Springs<br /> * Nuts and bolts, machine screws<br /> * Flat pencils<br /> * G-clamps<br /> * Battery charger for cordless tools<br /> * Vacuum cleaner (Henry)<br /> * Fretsaw<br /> * Chemicals cupboard (below worksurface): contains isopropyl alcohol for cleaning<br /> * [[Equipment/MitreSawRage3Db|Mitre Saw - Rage 3]]<br /> * [[Equipment/5704RK|Circular Saw - Makita ]]<br /> * [[Equipment/BandSaw|Band Saw]]<br /> * [[Equipment/CNC_Router|CNC Router]]<br /> <br /> ===Central island===<br /> <br /> * Steel rules, rulers, straight edges<br /> * Set squares<br /> * Spirit level<br /> <br /> In their own boxes under table:<br /> <br /> * Cordless drill<br /> * [[Equipment/5704RK|Circular Saw - Makita ]]<br /> * Jigsaw<br /> <br /> ===East side===<br /> <br /> On the right as you go in:<br /> <br /> * [[Equipment/WarcoMill|Mill - Warco ]]<br /> * [[Equipment/Lathe|Lathe - Myford]]<br /> * [[Equipment/Drill_Presses|Drill Presses]]<br /> * [[Equipment/Grinder|Grinder]]<br /> * Clamps<br /> * Pop rivets and rivet tool<br /> * Small nuts and bolts<br /> * Drill bits<br /> * [[Equipment/WoodLathe|Woodworking Lathe]]<br /> <br /> In storage bins:<br /> * Files<br /> * Screwdrivers<br /> * Allen keys (Hex keys)<br /> * Torx keys (Star screwdrivers)<br /> <br /> Hand tools on shadowboard:<br /> * Hammers<br /> * Hacksaws<br /> * Pliers<br /> <br /> ==The treasure trove==<br /> <br /> === Wall nearest door ===<br /> <br /> * Old disk drives including floppy drives<br /> <br /> === Near side of central shelves ===<br /> <br /> * Old audio / video stuff you could rebuild for something<br /> * Personal supplies of flat stuff that is too big for elsewhere<br /> * Old &quot;tower&quot; computer cases<br /> <br /> === Far side of central shelves ===<br /> <br /> * Electrical cables selection<br /> * Bits of cameras<br /> * Computer (ATX?) PSUs<br /> <br /> === Far shelves ===<br /> <br /> * Mains power supplies of many kinds<br /> * Fans<br /> * Capacitors<br /> * Resistors<br /> <br /> === Unclassified location ===<br /> <br /> * Various electrical connections and fittings<br /> * Multi-way mains extensions<br /> * Nabaztags (electric rabbits)<br /> * Just about anything for repurposing<br /> * Sledgehammer (broken handle, belongs to Visventis)<br /> <br /> ==The kitchen (Cakespace)==<br /> <br /> * Kettle<br /> * Oven<br /> * Microwave<br /> * Drinks<br /> * Snacks<br /> * Liquid soap<br /> * Cleaning materials<br /> <br /> ==Craft Room==<br /> <br /> * Vinyl cutter<br /> * Vinyl cutter stock<br /> * Eggbot<br /> * Knitting machine<br /> * Sewing machines<br /> * T-shirt press<br /> * Crafting table<br /> <br /> ==Unknown location==<br /> <br /> If you know where the things in this section are, please move their names to the appropriate section.</div>

JCGS http://wiki.makespace.org/Things_and_stuff 2015-10-24T22:25:09Z

<p>JCGS: /* West side */</p> <hr /> <div>For larger items, see the [[Equipment]] page.<br /> <br /> This page is to help you to find smaller items, and to help you to put them back in the right place so others can find them. (Use the in-page search in your browser.)<br /> <br /> Some items have extra names in brackets after their usual name; please include all names that people might use to search for a particular item.<br /> <br /> ==The corridor==<br /> <br /> * Badger<br /> * Showcase<br /> * Cupboards including Arduinos, personal laser stock, Family Makers supplies<br /> * Coats<br /> * Lost property<br /> * [[Infrastructure/Member Personal Storage|Personal storage boxes]]<br /> <br /> ==The classroom==<br /> <br /> * [[Classroom/Projector|Projector]]<br /> * [[Classroom/Seating|Stacking chairs]]<br /> * Folding tables<br /> * Non-stacking, non-folding sofas<br /> <br /> ==Main space==<br /> <br /> {|<br /> |+ Main Space<br /> |-<br /> ! South<br /> ! aisle<br /> ! Central<br /> ! aisle<br /> ! North<br /> |-<br /> |<br /> | Windowsill<br /> | Door from corridor<br /> | Windowsill with landline phone<br /> |<br /> |-<br /> | [[Equipment/Glassworking|Glassworking kiln, torch and associated tools]]<br /> [[File:Glassworking.jpg]]<br /> * Kiln<br /> * Torch<br /> | [[Equipment/VacuumFormer|Vacuum Former]]<br /> [[File:Vacuum-former.jpg]]<br /> |<br /> | Wire and components<br /> * Capacitors<br /> * Resistors<br /> * 74nn ICs (7400 series)<br /> * Wire<br /> | Electronics workbench<br /> * Insulating tape<br /> * Wire strippers<br /> * Pliers<br /> * Needle files<br /> * Screwdrivers<br /> |-<br /> | [[Equipment/Fine_metalwork_bench | Fine metalwork bench]]<br /> [[File:Fine-metalwork-bench.jpg]]<br /> * Dustbuster (small vacuum cleaner)<br /> * Flexible shaft tool<br /> * Scriber<br /> * Centre punch<br /> * Digital calipers (micrometer)<br /> * Flat Stake<br /> * Round triblet (for forming rings and suchlike)<br /> * Planishing Hammer (a polished-surface hammer for surface finishing and work-hardening)<br /> * Rawhide mallet (for hitting things without marking the surface)<br /> * Generic ball-pean hammer (a non-polished hammer for hitting punches etc.)<br /> |<br /> | Table<br /> |<br /> | Electronics workbench<br /> [[File:Electronics-workbenches.jpg]]<br /> On shelves:<br /> * BNC connectors, aerial connectors<br /> * More wire<br /> * Screwdrives, small pliers, etc<br /> * Stripboard<br /> * Solder suckers<br /> * Voltmeters<br /> * Soldering iron tips<br /> * PSUs (Power Supply Units)<br /> * Breadboards<br /> |-<br /> | Laser cutter stock<br /> [[File:Laser-stock.jpg]]<br /> |<br /> | Table<br /> [[File:White-table.jpg]]<br /> |<br /> | Desk<br /> |-<br /> | Laser cutter computer<br /> [[File:Betsy-desk.jpg]]<br /> |<br /> |<br /> |<br /> | Ultimaker [[Equipment/3D_Printer|3D Printers (FDM)]]<br /> [[File:Ultimaker.jpg]]<br /> |-<br /> | [[Equipment/Laser_Cutter|Laser Cutter]]<br /> [[File:Betsy.jpg]]<br /> | Laser cutter computer<br /> [[File:Jaws-computer.jpg]]<br /> * Swarfega wipes<br /> | [[Equipment/Laser_Cutter|Laser Cutter]]<br /> [[File:Jaws.jpg]]<br /> |<br /> | Makerbot<br /> [[File:Makerbot.jpg]]<br /> * Printer thread<br /> |-<br /> | Formlabs 3D printer<br /> [[File:Formlabs.jpg]]<br /> |<br /> |<br /> |<br /> |<br /> * [[Equipment/CNC_Model_Mill|CNC Model Mill]]<br /> [[File:Roland-mill.jpg]]<br /> * Plates for model mill<br /> |-<br /> | Formlabs desk<br /> [[File:Chargers.jpg]]<br /> * Automatic plant watering system<br /> * AA (etc) battery chargers<br /> |<br /> | Table<br /> |<br /> | Sink area<br /> [[File:Sink-area.jpg]]<br /> * First aid kit<br /> * Eye washout kit<br /> * Torch<br /> * Cleaning cloths<br /> * Liquid soap<br /> * Swarfega<br /> * Fly spray (insecticide)<br /> * Watering can<br /> * Plant food (Baby Bio)<br /> |-<br /> | Desks<br /> [[File:Assorted-desk.jpg]]<br /> |<br /> | Table<br /> |<br /> | [[Equipment/Screenprinting|Screenprinting area]]<br /> [[File:Screen-printing-area.jpg]]<br /> * Screen printing equipment<br /> * Drying racks<br /> |-<br /> | [[Equipment/Plotter|HP 750C A0 Plotter]]<br /> [[File:Plotter.jpg]]<br /> |<br /> | Table<br /> [[File:Big-table.jpg]]<br /> General hacking area<br /> * Mains sockets<br /> * USB chargers<br /> |<br /> | Door to workshop<br /> |-<br /> | [[Equipment/Paper Printers|Paper printers]]<br /> [[File:Laser-printers.jpg]]<br /> * Paper<br /> * Stationery including pens, sellotape, whiteboard pens<br /> * CAT-5?<br /> |<br /> | Table<br /> |<br /> | Big shelves<br /> [[File:Deep-shelves.jpg]]<br /> * PPE (goggles, ear protectors, dustmasks)<br /> * PAT testing queue<br /> * Duct tape<br /> * Mains extension reels<br /> * PVA<br /> * Hot air guns (paint strippers)<br /> * Tape measures<br /> |-<br /> | Stair landing to kitchen<br /> | Stairs to kitchen<br /> | Plants and flat storage<br /> * Crimping tools<br /> * Craft knives<br /> * Cable ties<br /> * Rawlplugs<br /> * Watch batteries / button cells<br /> | Fire exit / door to big bins<br /> | Wood offcuts for recycling<br /> |}<br /> <br /> ==The workshop==<br /> <br /> ===West side===<br /> <br /> On the left as you go in:<br /> <br /> * Springs<br /> * Nuts and bolts, machine screws<br /> * Flat pencils<br /> * G-clamps<br /> * Battery charger for cordless tools<br /> * Vacuum cleaner (Henry)<br /> * Fretsaw<br /> * Chemicals cupboard (below worksurface): contains isopropyl alcohol for cleaning<br /> * [[Equipment/MitreSawRage3Db|Mitre Saw - Rage 3]]<br /> * [[Equipment/5704RK|Circular Saw - Makita ]]<br /> * [[Equipment/BandSaw|Band Saw]]<br /> * [[Equipment/CNC_Router|CNC Router]]<br /> <br /> ===Central island===<br /> <br /> * Steel rules, rulers, straight edges<br /> * Set squares<br /> * Spirit level<br /> <br /> In their own boxes under table:<br /> <br /> * Cordless drill<br /> * [[Equipment/5704RK|Circular Saw - Makita ]]<br /> * Jigsaw<br /> <br /> ===East side===<br /> <br /> On the right as you go in:<br /> <br /> * [[Equipment/WarcoMill|Mill - Warco ]]<br /> * [[Equipment/Lathe|Lathe - Myford]]<br /> * [[Equipment/Drill_Presses|Drill Presses]]<br /> * [[Equipment/Grinder|Grinder]]<br /> * Clamps<br /> * Pop rivets and rivet tool<br /> * Small nuts and bolts<br /> * Drill bits<br /> * [[Equipment/WoodLathe|Woodworking Lathe]]<br /> <br /> In storage bins:<br /> * Files<br /> * Screwdrivers<br /> * Allen keys (Hex keys)<br /> * Torx keys (Star screwdrivers)<br /> <br /> Hand tools on shadowboard:<br /> * Hammers<br /> * Hacksaws<br /> * Pliers<br /> <br /> ==The treasure trove==<br /> <br /> * Capacitors<br /> * Resistors<br /> * Various electrical connections and fittings<br /> * Electrical cables selection<br /> * Multi-way mains extensions<br /> * Nabaztags (electric rabbits)<br /> * Just about anything for repurposing<br /> * Bits of cameras<br /> * Old audio / video stuff you could rebuild for something<br /> * Personal supplies of flat stuff that is too big for elsewhere<br /> * Sledgehammer (broken handle, belongs to Visventis)<br /> <br /> ==The kitchen (Cakespace)==<br /> <br /> * Kettle<br /> * Oven<br /> * Microwave<br /> * Drinks<br /> * Snacks<br /> * Liquid soap<br /> * Cleaning materials<br /> <br /> ==Craft Room==<br /> <br /> * Vinyl cutter<br /> * Vinyl cutter stock<br /> * Eggbot<br /> * Knitting machine<br /> * Sewing machines<br /> * T-shirt press<br /> * Crafting table<br /> <br /> ==Unknown location==<br /> <br /> If you know where the things in this section are, please move their names to the appropriate section.</div>

JCGS http://wiki.makespace.org/Things_and_stuff 2015-10-24T22:24:06Z

<p>JCGS: /* East side */</p> <hr /> <div>For larger items, see the [[Equipment]] page.<br /> <br /> This page is to help you to find smaller items, and to help you to put them back in the right place so others can find them. (Use the in-page search in your browser.)<br /> <br /> Some items have extra names in brackets after their usual name; please include all names that people might use to search for a particular item.<br /> <br /> ==The corridor==<br /> <br /> * Badger<br /> * Showcase<br /> * Cupboards including Arduinos, personal laser stock, Family Makers supplies<br /> * Coats<br /> * Lost property<br /> * [[Infrastructure/Member Personal Storage|Personal storage boxes]]<br /> <br /> ==The classroom==<br /> <br /> * [[Classroom/Projector|Projector]]<br /> * [[Classroom/Seating|Stacking chairs]]<br /> * Folding tables<br /> * Non-stacking, non-folding sofas<br /> <br /> ==Main space==<br /> <br /> {|<br /> |+ Main Space<br /> |-<br /> ! South<br /> ! aisle<br /> ! Central<br /> ! aisle<br /> ! North<br /> |-<br /> |<br /> | Windowsill<br /> | Door from corridor<br /> | Windowsill with landline phone<br /> |<br /> |-<br /> | [[Equipment/Glassworking|Glassworking kiln, torch and associated tools]]<br /> [[File:Glassworking.jpg]]<br /> * Kiln<br /> * Torch<br /> | [[Equipment/VacuumFormer|Vacuum Former]]<br /> [[File:Vacuum-former.jpg]]<br /> |<br /> | Wire and components<br /> * Capacitors<br /> * Resistors<br /> * 74nn ICs (7400 series)<br /> * Wire<br /> | Electronics workbench<br /> * Insulating tape<br /> * Wire strippers<br /> * Pliers<br /> * Needle files<br /> * Screwdrivers<br /> |-<br /> | [[Equipment/Fine_metalwork_bench | Fine metalwork bench]]<br /> [[File:Fine-metalwork-bench.jpg]]<br /> * Dustbuster (small vacuum cleaner)<br /> * Flexible shaft tool<br /> * Scriber<br /> * Centre punch<br /> * Digital calipers (micrometer)<br /> * Flat Stake<br /> * Round triblet (for forming rings and suchlike)<br /> * Planishing Hammer (a polished-surface hammer for surface finishing and work-hardening)<br /> * Rawhide mallet (for hitting things without marking the surface)<br /> * Generic ball-pean hammer (a non-polished hammer for hitting punches etc.)<br /> |<br /> | Table<br /> |<br /> | Electronics workbench<br /> [[File:Electronics-workbenches.jpg]]<br /> On shelves:<br /> * BNC connectors, aerial connectors<br /> * More wire<br /> * Screwdrives, small pliers, etc<br /> * Stripboard<br /> * Solder suckers<br /> * Voltmeters<br /> * Soldering iron tips<br /> * PSUs (Power Supply Units)<br /> * Breadboards<br /> |-<br /> | Laser cutter stock<br /> [[File:Laser-stock.jpg]]<br /> |<br /> | Table<br /> [[File:White-table.jpg]]<br /> |<br /> | Desk<br /> |-<br /> | Laser cutter computer<br /> [[File:Betsy-desk.jpg]]<br /> |<br /> |<br /> |<br /> | Ultimaker [[Equipment/3D_Printer|3D Printers (FDM)]]<br /> [[File:Ultimaker.jpg]]<br /> |-<br /> | [[Equipment/Laser_Cutter|Laser Cutter]]<br /> [[File:Betsy.jpg]]<br /> | Laser cutter computer<br /> [[File:Jaws-computer.jpg]]<br /> * Swarfega wipes<br /> | [[Equipment/Laser_Cutter|Laser Cutter]]<br /> [[File:Jaws.jpg]]<br /> |<br /> | Makerbot<br /> [[File:Makerbot.jpg]]<br /> * Printer thread<br /> |-<br /> | Formlabs 3D printer<br /> [[File:Formlabs.jpg]]<br /> |<br /> |<br /> |<br /> |<br /> * [[Equipment/CNC_Model_Mill|CNC Model Mill]]<br /> [[File:Roland-mill.jpg]]<br /> * Plates for model mill<br /> |-<br /> | Formlabs desk<br /> [[File:Chargers.jpg]]<br /> * Automatic plant watering system<br /> * AA (etc) battery chargers<br /> |<br /> | Table<br /> |<br /> | Sink area<br /> [[File:Sink-area.jpg]]<br /> * First aid kit<br /> * Eye washout kit<br /> * Torch<br /> * Cleaning cloths<br /> * Liquid soap<br /> * Swarfega<br /> * Fly spray (insecticide)<br /> * Watering can<br /> * Plant food (Baby Bio)<br /> |-<br /> | Desks<br /> [[File:Assorted-desk.jpg]]<br /> |<br /> | Table<br /> |<br /> | [[Equipment/Screenprinting|Screenprinting area]]<br /> [[File:Screen-printing-area.jpg]]<br /> * Screen printing equipment<br /> * Drying racks<br /> |-<br /> | [[Equipment/Plotter|HP 750C A0 Plotter]]<br /> [[File:Plotter.jpg]]<br /> |<br /> | Table<br /> [[File:Big-table.jpg]]<br /> General hacking area<br /> * Mains sockets<br /> * USB chargers<br /> |<br /> | Door to workshop<br /> |-<br /> | [[Equipment/Paper Printers|Paper printers]]<br /> [[File:Laser-printers.jpg]]<br /> * Paper<br /> * Stationery including pens, sellotape, whiteboard pens<br /> * CAT-5?<br /> |<br /> | Table<br /> |<br /> | Big shelves<br /> [[File:Deep-shelves.jpg]]<br /> * PPE (goggles, ear protectors, dustmasks)<br /> * PAT testing queue<br /> * Duct tape<br /> * Mains extension reels<br /> * PVA<br /> * Hot air guns (paint strippers)<br /> * Tape measures<br /> |-<br /> | Stair landing to kitchen<br /> | Stairs to kitchen<br /> | Plants and flat storage<br /> * Crimping tools<br /> * Craft knives<br /> * Cable ties<br /> * Rawlplugs<br /> * Watch batteries / button cells<br /> | Fire exit / door to big bins<br /> | Wood offcuts for recycling<br /> |}<br /> <br /> ==The workshop==<br /> <br /> ===West side===<br /> <br /> On the left as you go in:<br /> <br /> * Springs<br /> * Nuts and bolts, machine screws<br /> * Flat pencils<br /> * G-clamps<br /> * Battery charger for cordless tools<br /> * Vacuum cleaner (Henry)<br /> * Fretsaw<br /> * [[Equipment/MitreSawRage3Db|Mitre Saw - Rage 3]]<br /> * [[Equipment/5704RK|Circular Saw - Makita ]]<br /> * [[Equipment/BandSaw|Band Saw]]<br /> * [[Equipment/CNC_Router|CNC Router]]<br /> <br /> ===Central island===<br /> <br /> * Steel rules, rulers, straight edges<br /> * Set squares<br /> * Spirit level<br /> <br /> In their own boxes under table:<br /> <br /> * Cordless drill<br /> * [[Equipment/5704RK|Circular Saw - Makita ]]<br /> * Jigsaw<br /> <br /> ===East side===<br /> <br /> On the right as you go in:<br /> <br /> * [[Equipment/WarcoMill|Mill - Warco ]]<br /> * [[Equipment/Lathe|Lathe - Myford]]<br /> * [[Equipment/Drill_Presses|Drill Presses]]<br /> * [[Equipment/Grinder|Grinder]]<br /> * Clamps<br /> * Pop rivets and rivet tool<br /> * Small nuts and bolts<br /> * Drill bits<br /> * [[Equipment/WoodLathe|Woodworking Lathe]]<br /> <br /> In storage bins:<br /> * Files<br /> * Screwdrivers<br /> * Allen keys (Hex keys)<br /> * Torx keys (Star screwdrivers)<br /> <br /> Hand tools on shadowboard:<br /> * Hammers<br /> * Hacksaws<br /> * Pliers<br /> <br /> ==The treasure trove==<br /> <br /> * Capacitors<br /> * Resistors<br /> * Various electrical connections and fittings<br /> * Electrical cables selection<br /> * Multi-way mains extensions<br /> * Nabaztags (electric rabbits)<br /> * Just about anything for repurposing<br /> * Bits of cameras<br /> * Old audio / video stuff you could rebuild for something<br /> * Personal supplies of flat stuff that is too big for elsewhere<br /> * Sledgehammer (broken handle, belongs to Visventis)<br /> <br /> ==The kitchen (Cakespace)==<br /> <br /> * Kettle<br /> * Oven<br /> * Microwave<br /> * Drinks<br /> * Snacks<br /> * Liquid soap<br /> * Cleaning materials<br /> <br /> ==Craft Room==<br /> <br /> * Vinyl cutter<br /> * Vinyl cutter stock<br /> * Eggbot<br /> * Knitting machine<br /> * Sewing machines<br /> * T-shirt press<br /> * Crafting table<br /> <br /> ==Unknown location==<br /> <br /> If you know where the things in this section are, please move their names to the appropriate section.</div>

JCGS http://wiki.makespace.org/Things_and_stuff 2015-10-24T22:22:03Z

<p>JCGS: /* Central island */</p> <hr /> <div>For larger items, see the [[Equipment]] page.<br /> <br /> This page is to help you to find smaller items, and to help you to put them back in the right place so others can find them. (Use the in-page search in your browser.)<br /> <br /> Some items have extra names in brackets after their usual name; please include all names that people might use to search for a particular item.<br /> <br /> ==The corridor==<br /> <br /> * Badger<br /> * Showcase<br /> * Cupboards including Arduinos, personal laser stock, Family Makers supplies<br /> * Coats<br /> * Lost property<br /> * [[Infrastructure/Member Personal Storage|Personal storage boxes]]<br /> <br /> ==The classroom==<br /> <br /> * [[Classroom/Projector|Projector]]<br /> * [[Classroom/Seating|Stacking chairs]]<br /> * Folding tables<br /> * Non-stacking, non-folding sofas<br /> <br /> ==Main space==<br /> <br /> {|<br /> |+ Main Space<br /> |-<br /> ! South<br /> ! aisle<br /> ! Central<br /> ! aisle<br /> ! North<br /> |-<br /> |<br /> | Windowsill<br /> | Door from corridor<br /> | Windowsill with landline phone<br /> |<br /> |-<br /> | [[Equipment/Glassworking|Glassworking kiln, torch and associated tools]]<br /> [[File:Glassworking.jpg]]<br /> * Kiln<br /> * Torch<br /> | [[Equipment/VacuumFormer|Vacuum Former]]<br /> [[File:Vacuum-former.jpg]]<br /> |<br /> | Wire and components<br /> * Capacitors<br /> * Resistors<br /> * 74nn ICs (7400 series)<br /> * Wire<br /> | Electronics workbench<br /> * Insulating tape<br /> * Wire strippers<br /> * Pliers<br /> * Needle files<br /> * Screwdrivers<br /> |-<br /> | [[Equipment/Fine_metalwork_bench | Fine metalwork bench]]<br /> [[File:Fine-metalwork-bench.jpg]]<br /> * Dustbuster (small vacuum cleaner)<br /> * Flexible shaft tool<br /> * Scriber<br /> * Centre punch<br /> * Digital calipers (micrometer)<br /> * Flat Stake<br /> * Round triblet (for forming rings and suchlike)<br /> * Planishing Hammer (a polished-surface hammer for surface finishing and work-hardening)<br /> * Rawhide mallet (for hitting things without marking the surface)<br /> * Generic ball-pean hammer (a non-polished hammer for hitting punches etc.)<br /> |<br /> | Table<br /> |<br /> | Electronics workbench<br /> [[File:Electronics-workbenches.jpg]]<br /> On shelves:<br /> * BNC connectors, aerial connectors<br /> * More wire<br /> * Screwdrives, small pliers, etc<br /> * Stripboard<br /> * Solder suckers<br /> * Voltmeters<br /> * Soldering iron tips<br /> * PSUs (Power Supply Units)<br /> * Breadboards<br /> |-<br /> | Laser cutter stock<br /> [[File:Laser-stock.jpg]]<br /> |<br /> | Table<br /> [[File:White-table.jpg]]<br /> |<br /> | Desk<br /> |-<br /> | Laser cutter computer<br /> [[File:Betsy-desk.jpg]]<br /> |<br /> |<br /> |<br /> | Ultimaker [[Equipment/3D_Printer|3D Printers (FDM)]]<br /> [[File:Ultimaker.jpg]]<br /> |-<br /> | [[Equipment/Laser_Cutter|Laser Cutter]]<br /> [[File:Betsy.jpg]]<br /> | Laser cutter computer<br /> [[File:Jaws-computer.jpg]]<br /> * Swarfega wipes<br /> | [[Equipment/Laser_Cutter|Laser Cutter]]<br /> [[File:Jaws.jpg]]<br /> |<br /> | Makerbot<br /> [[File:Makerbot.jpg]]<br /> * Printer thread<br /> |-<br /> | Formlabs 3D printer<br /> [[File:Formlabs.jpg]]<br /> |<br /> |<br /> |<br /> |<br /> * [[Equipment/CNC_Model_Mill|CNC Model Mill]]<br /> [[File:Roland-mill.jpg]]<br /> * Plates for model mill<br /> |-<br /> | Formlabs desk<br /> [[File:Chargers.jpg]]<br /> * Automatic plant watering system<br /> * AA (etc) battery chargers<br /> |<br /> | Table<br /> |<br /> | Sink area<br /> [[File:Sink-area.jpg]]<br /> * First aid kit<br /> * Eye washout kit<br /> * Torch<br /> * Cleaning cloths<br /> * Liquid soap<br /> * Swarfega<br /> * Fly spray (insecticide)<br /> * Watering can<br /> * Plant food (Baby Bio)<br /> |-<br /> | Desks<br /> [[File:Assorted-desk.jpg]]<br /> |<br /> | Table<br /> |<br /> | [[Equipment/Screenprinting|Screenprinting area]]<br /> [[File:Screen-printing-area.jpg]]<br /> * Screen printing equipment<br /> * Drying racks<br /> |-<br /> | [[Equipment/Plotter|HP 750C A0 Plotter]]<br /> [[File:Plotter.jpg]]<br /> |<br /> | Table<br /> [[File:Big-table.jpg]]<br /> General hacking area<br /> * Mains sockets<br /> * USB chargers<br /> |<br /> | Door to workshop<br /> |-<br /> | [[Equipment/Paper Printers|Paper printers]]<br /> [[File:Laser-printers.jpg]]<br /> * Paper<br /> * Stationery including pens, sellotape, whiteboard pens<br /> * CAT-5?<br /> |<br /> | Table<br /> |<br /> | Big shelves<br /> [[File:Deep-shelves.jpg]]<br /> * PPE (goggles, ear protectors, dustmasks)<br /> * PAT testing queue<br /> * Duct tape<br /> * Mains extension reels<br /> * PVA<br /> * Hot air guns (paint strippers)<br /> * Tape measures<br /> |-<br /> | Stair landing to kitchen<br /> | Stairs to kitchen<br /> | Plants and flat storage<br /> * Crimping tools<br /> * Craft knives<br /> * Cable ties<br /> * Rawlplugs<br /> * Watch batteries / button cells<br /> | Fire exit / door to big bins<br /> | Wood offcuts for recycling<br /> |}<br /> <br /> ==The workshop==<br /> <br /> ===West side===<br /> <br /> On the left as you go in:<br /> <br /> * Springs<br /> * Nuts and bolts, machine screws<br /> * Flat pencils<br /> * G-clamps<br /> * Battery charger for cordless tools<br /> * Vacuum cleaner (Henry)<br /> * Fretsaw<br /> * [[Equipment/MitreSawRage3Db|Mitre Saw - Rage 3]]<br /> * [[Equipment/5704RK|Circular Saw - Makita ]]<br /> * [[Equipment/BandSaw|Band Saw]]<br /> * [[Equipment/CNC_Router|CNC Router]]<br /> <br /> ===Central island===<br /> <br /> * Steel rules, rulers, straight edges<br /> * Set squares<br /> * Spirit level<br /> <br /> In their own boxes under table:<br /> <br /> * Cordless drill<br /> * [[Equipment/5704RK|Circular Saw - Makita ]]<br /> * Jigsaw<br /> <br /> ===East side===<br /> <br /> On the right as you go in:<br /> <br /> * [[Equipment/WarcoMill|Mill - Warco ]]<br /> * [[Equipment/Lathe|Lathe - Myford]]<br /> * [[Equipment/Drill_Presses|Drill Presses]]<br /> * [[Equipment/Grinder|Grinder]]<br /> * Hammers<br /> * Clamps<br /> * Pop rivets and rivet tool<br /> * Small nuts and bolts<br /> * Files<br /> * Screwdrivers<br /> * Allen keys (Hex keys)<br /> * Torx keys (Star screwdrivers)<br /> * Drill bits<br /> * [[Equipment/WoodLathe|Woodworking Lathe]]<br /> <br /> ==The treasure trove==<br /> <br /> * Capacitors<br /> * Resistors<br /> * Various electrical connections and fittings<br /> * Electrical cables selection<br /> * Multi-way mains extensions<br /> * Nabaztags (electric rabbits)<br /> * Just about anything for repurposing<br /> * Bits of cameras<br /> * Old audio / video stuff you could rebuild for something<br /> * Personal supplies of flat stuff that is too big for elsewhere<br /> * Sledgehammer (broken handle, belongs to Visventis)<br /> <br /> ==The kitchen (Cakespace)==<br /> <br /> * Kettle<br /> * Oven<br /> * Microwave<br /> * Drinks<br /> * Snacks<br /> * Liquid soap<br /> * Cleaning materials<br /> <br /> ==Craft Room==<br /> <br /> * Vinyl cutter<br /> * Vinyl cutter stock<br /> * Eggbot<br /> * Knitting machine<br /> * Sewing machines<br /> * T-shirt press<br /> * Crafting table<br /> <br /> ==Unknown location==<br /> <br /> If you know where the things in this section are, please move their names to the appropriate section.</div>

JCGS http://wiki.makespace.org/Things_and_stuff 2015-10-24T22:19:15Z

<p>JCGS: /* Main space */</p> <hr /> <div>For larger items, see the [[Equipment]] page.<br /> <br /> This page is to help you to find smaller items, and to help you to put them back in the right place so others can find them. (Use the in-page search in your browser.)<br /> <br /> Some items have extra names in brackets after their usual name; please include all names that people might use to search for a particular item.<br /> <br /> ==The corridor==<br /> <br /> * Badger<br /> * Showcase<br /> * Cupboards including Arduinos, personal laser stock, Family Makers supplies<br /> * Coats<br /> * Lost property<br /> * [[Infrastructure/Member Personal Storage|Personal storage boxes]]<br /> <br /> ==The classroom==<br /> <br /> * [[Classroom/Projector|Projector]]<br /> * [[Classroom/Seating|Stacking chairs]]<br /> * Folding tables<br /> * Non-stacking, non-folding sofas<br /> <br /> ==Main space==<br /> <br /> {|<br /> |+ Main Space<br /> |-<br /> ! South<br /> ! aisle<br /> ! Central<br /> ! aisle<br /> ! North<br /> |-<br /> |<br /> | Windowsill<br /> | Door from corridor<br /> | Windowsill with landline phone<br /> |<br /> |-<br /> | [[Equipment/Glassworking|Glassworking kiln, torch and associated tools]]<br /> [[File:Glassworking.jpg]]<br /> * Kiln<br /> * Torch<br /> | [[Equipment/VacuumFormer|Vacuum Former]]<br /> [[File:Vacuum-former.jpg]]<br /> |<br /> | Wire and components<br /> * Capacitors<br /> * Resistors<br /> * 74nn ICs (7400 series)<br /> * Wire<br /> | Electronics workbench<br /> * Insulating tape<br /> * Wire strippers<br /> * Pliers<br /> * Needle files<br /> * Screwdrivers<br /> |-<br /> | [[Equipment/Fine_metalwork_bench | Fine metalwork bench]]<br /> [[File:Fine-metalwork-bench.jpg]]<br /> * Dustbuster (small vacuum cleaner)<br /> * Flexible shaft tool<br /> * Scriber<br /> * Centre punch<br /> * Digital calipers (micrometer)<br /> * Flat Stake<br /> * Round triblet (for forming rings and suchlike)<br /> * Planishing Hammer (a polished-surface hammer for surface finishing and work-hardening)<br /> * Rawhide mallet (for hitting things without marking the surface)<br /> * Generic ball-pean hammer (a non-polished hammer for hitting punches etc.)<br /> |<br /> | Table<br /> |<br /> | Electronics workbench<br /> [[File:Electronics-workbenches.jpg]]<br /> On shelves:<br /> * BNC connectors, aerial connectors<br /> * More wire<br /> * Screwdrives, small pliers, etc<br /> * Stripboard<br /> * Solder suckers<br /> * Voltmeters<br /> * Soldering iron tips<br /> * PSUs (Power Supply Units)<br /> * Breadboards<br /> |-<br /> | Laser cutter stock<br /> [[File:Laser-stock.jpg]]<br /> |<br /> | Table<br /> [[File:White-table.jpg]]<br /> |<br /> | Desk<br /> |-<br /> | Laser cutter computer<br /> [[File:Betsy-desk.jpg]]<br /> |<br /> |<br /> |<br /> | Ultimaker [[Equipment/3D_Printer|3D Printers (FDM)]]<br /> [[File:Ultimaker.jpg]]<br /> |-<br /> | [[Equipment/Laser_Cutter|Laser Cutter]]<br /> [[File:Betsy.jpg]]<br /> | Laser cutter computer<br /> [[File:Jaws-computer.jpg]]<br /> * Swarfega wipes<br /> | [[Equipment/Laser_Cutter|Laser Cutter]]<br /> [[File:Jaws.jpg]]<br /> |<br /> | Makerbot<br /> [[File:Makerbot.jpg]]<br /> * Printer thread<br /> |-<br /> | Formlabs 3D printer<br /> [[File:Formlabs.jpg]]<br /> |<br /> |<br /> |<br /> |<br /> * [[Equipment/CNC_Model_Mill|CNC Model Mill]]<br /> [[File:Roland-mill.jpg]]<br /> * Plates for model mill<br /> |-<br /> | Formlabs desk<br /> [[File:Chargers.jpg]]<br /> * Automatic plant watering system<br /> * AA (etc) battery chargers<br /> |<br /> | Table<br /> |<br /> | Sink area<br /> [[File:Sink-area.jpg]]<br /> * First aid kit<br /> * Eye washout kit<br /> * Torch<br /> * Cleaning cloths<br /> * Liquid soap<br /> * Swarfega<br /> * Fly spray (insecticide)<br /> * Watering can<br /> * Plant food (Baby Bio)<br /> |-<br /> | Desks<br /> [[File:Assorted-desk.jpg]]<br /> |<br /> | Table<br /> |<br /> | [[Equipment/Screenprinting|Screenprinting area]]<br /> [[File:Screen-printing-area.jpg]]<br /> * Screen printing equipment<br /> * Drying racks<br /> |-<br /> | [[Equipment/Plotter|HP 750C A0 Plotter]]<br /> [[File:Plotter.jpg]]<br /> |<br /> | Table<br /> [[File:Big-table.jpg]]<br /> General hacking area<br /> * Mains sockets<br /> * USB chargers<br /> |<br /> | Door to workshop<br /> |-<br /> | [[Equipment/Paper Printers|Paper printers]]<br /> [[File:Laser-printers.jpg]]<br /> * Paper<br /> * Stationery including pens, sellotape, whiteboard pens<br /> * CAT-5?<br /> |<br /> | Table<br /> |<br /> | Big shelves<br /> [[File:Deep-shelves.jpg]]<br /> * PPE (goggles, ear protectors, dustmasks)<br /> * PAT testing queue<br /> * Duct tape<br /> * Mains extension reels<br /> * PVA<br /> * Hot air guns (paint strippers)<br /> * Tape measures<br /> |-<br /> | Stair landing to kitchen<br /> | Stairs to kitchen<br /> | Plants and flat storage<br /> * Crimping tools<br /> * Craft knives<br /> * Cable ties<br /> * Rawlplugs<br /> * Watch batteries / button cells<br /> | Fire exit / door to big bins<br /> | Wood offcuts for recycling<br /> |}<br /> <br /> ==The workshop==<br /> <br /> ===West side===<br /> <br /> On the left as you go in:<br /> <br /> * Springs<br /> * Nuts and bolts, machine screws<br /> * Flat pencils<br /> * G-clamps<br /> * Battery charger for cordless tools<br /> * Vacuum cleaner (Henry)<br /> * Fretsaw<br /> * [[Equipment/MitreSawRage3Db|Mitre Saw - Rage 3]]<br /> * [[Equipment/5704RK|Circular Saw - Makita ]]<br /> * [[Equipment/BandSaw|Band Saw]]<br /> * [[Equipment/CNC_Router|CNC Router]]<br /> <br /> ===Central island===<br /> <br /> * Steel rules, rulers, straight edges<br /> * Set squares<br /> * Spirit level<br /> * Cordless drill<br /> * [[Equipment/5704RK|Circular Saw - Makita ]]<br /> * Jigsaw<br /> <br /> ===East side===<br /> <br /> On the right as you go in:<br /> <br /> * [[Equipment/WarcoMill|Mill - Warco ]]<br /> * [[Equipment/Lathe|Lathe - Myford]]<br /> * [[Equipment/Drill_Presses|Drill Presses]]<br /> * [[Equipment/Grinder|Grinder]]<br /> * Hammers<br /> * Clamps<br /> * Pop rivets and rivet tool<br /> * Small nuts and bolts<br /> * Files<br /> * Screwdrivers<br /> * Allen keys (Hex keys)<br /> * Torx keys (Star screwdrivers)<br /> * Drill bits<br /> * [[Equipment/WoodLathe|Woodworking Lathe]]<br /> <br /> ==The treasure trove==<br /> <br /> * Capacitors<br /> * Resistors<br /> * Various electrical connections and fittings<br /> * Electrical cables selection<br /> * Multi-way mains extensions<br /> * Nabaztags (electric rabbits)<br /> * Just about anything for repurposing<br /> * Bits of cameras<br /> * Old audio / video stuff you could rebuild for something<br /> * Personal supplies of flat stuff that is too big for elsewhere<br /> * Sledgehammer (broken handle, belongs to Visventis)<br /> <br /> ==The kitchen (Cakespace)==<br /> <br /> * Kettle<br /> * Oven<br /> * Microwave<br /> * Drinks<br /> * Snacks<br /> * Liquid soap<br /> * Cleaning materials<br /> <br /> ==Craft Room==<br /> <br /> * Vinyl cutter<br /> * Vinyl cutter stock<br /> * Eggbot<br /> * Knitting machine<br /> * Sewing machines<br /> * T-shirt press<br /> * Crafting table<br /> <br /> ==Unknown location==<br /> <br /> If you know where the things in this section are, please move their names to the appropriate section.</div>

JCGS