http://wiki.makespace.org/api.php?action=feedcontributions&user=Danieljabailey&feedformat=atomMakespace - User contributions [en]2024-03-29T09:08:26ZUser contributionsMediaWiki 1.22.6http://wiki.makespace.org/Equipment/3D_Printer/UM2TrainingEquipment/3D Printer/UM2Training2016-08-12T20:22:50Z<p>Danieljabailey: /* Trained Users */ Added users trained 2016-08-12</p>
<hr />
<div>[[Equipment|Equipment]] / [[Equipment/3D Printer|UM2]] / Training<br />
<br />
= Ultimaker 2 3D Printer Training =<br />
<br />
This page documents the process for being trained on the Ultimaker 2 Printer, and the list of members who have completed that training.<br />
<br />
== Summary ==<br />
<br />
Training takes place in three main steps:<br />
* Group Training of 1-4 members, going through the equipment and how to use it (~1hr)<br />
* Individual Training Task, where an individual member is set a task to complete to prove and improve understanding (~20min each)<br />
* Recommended project oversight, where more experienced users oversee the projects being undertaken when cutting (first 2-3 projects)<br />
<br />
A shorter conversion training session is available for members who were previously signed off to use the Makerbot 2X printer. These sessions last around 20 minutes and do not include individual sessions.<br />
<br />
== Booking ==<br />
<br />
For discussing and arranging slots, please use the mailing list. New training sessions will be announced on the Meetup group.<br />
<br />
Notes:<br />
* You can only be trained if you have RSVP'd to a Meetup session<br />
<br />
== Training Cheatsheet - Conversion Course ==<br />
<br />
Members already trained on and familiar with the Makerbot 2X can attend this short conversion course to be signed off to use the Ultimaker 2 3D printer. Up to 10 people can be accommodated on each course, which lasts 20 to 30 minutes.<br />
<br />
1. Physical Differences from the 2X<br />
* Glass build plate, no kapton tape<br />
* Single extruder<br />
* Push feed<br />
<br />
2. General<br />
* Use the correct filament (2.85mm, NOT 3mm or 1.75mm)<br />
* New filament storage system<br />
<br />
3. Printing<br />
* Fence / Brim / Raft<br />
* OK to leave printer unattended after the first few layers<br />
* Camera available for remote monitoring<br />
* Use only plastic implements for part removal, take care not to melt them on the hot end<br />
<br />
4. Cura Software<br />
* Import and place<br />
* Simple mode<br />
* Brief overview of advanced mode<br />
* Temperature set on printer not slicer<br />
* Exporting to SD card<br />
<br />
5. Unload / Load filament<br />
* How to feed (slow first, then fast)<br />
* Select correct material in menu<br />
* Changing temperature and speed parameters from printer<br />
* Demonstrate the atomic method of cleaning the extruder to prevent feed jams<br />
<br />
6. Filament pricing<br />
* 5p per gram for PLA and ABS, to be kept under review<br />
* Include wastage!<br />
<br />
== Training Cheatsheet - Full Course ==<br />
<br />
'''Group Session'''<br />
<br />
1. Ask what each member hopes to get out of the 3D printer.<br />
<br />
2. Explain how 3D printing works<br />
<br />
3. Safety<br />
* Burn hazard – nozzle and build plate<br />
* Unit may move unexpectedly<br />
* Avoid prolonged exposure to ABS fumes<br />
<br />
4. Damage to machine<br />
* Fragile build plate<br />
* Jammed filament<br />
<br />
5. General<br />
* Use the correct filament (2.85mm)<br />
* Filament storage and feed system<br />
* Switch off when finished<br />
* Leave levelling to the owners but report any problems<br />
<br />
6. PLA vs ABS<br />
* How to tell the difference<br />
* Different temperature<br />
* PLA Biodegradable<br />
<br />
7. Software / workflow<br />
* Importing<br />
* Positioning on bed<br />
* Supports<br />
* Setting quality / speed trade off<br />
* Advanced options<br />
* Exporting to SD card<br />
<br />
8. Unload / load<br />
* Attaching spool or loading from storage box<br />
* Feeding (slow then fast)<br />
* Beware of wrapping round axle<br />
* Setting material in menu<br />
* Adjusting parameters, e.g. ABS plate temperature<br />
<br />
9. Printing<br />
* Preheating<br />
* Fence printing<br />
* Keep an eye on progress, locally or with camera<br />
* If leaving unattended, put a post-it with your contact details<br />
* Use only plastic implements for part removal<br />
<br />
10. Other stuff<br />
* Demonstrate atomic method of cleaning the nozzle to prevent feed jams<br />
* Strength characteristics – orientation is important<br />
* Paying<br />
<br />
'''Individual Training Task'''<br />
<br />
Task<br />
* Should demonstrate import, setup, position and run<br />
* Choose a part that takes about 10 mins to print (preloaded on PC)<br />
<br />
Steps<br />
* Set individual to work, don't prompt but do answer questions (or pose if needed)<br />
* Talk through design once done, question/check things etc<br />
* Proceed to printing (watch carefully all steps)<br />
<br />
Assuming all ok:<br />
* Get them to read the health and safety notes about operation and materials<br />
* Add to the trained member list<br />
<br />
'''Project Oversight'''<br />
<br />
For next 2-3 projects, recommend member will find another more experienced trained user to support them (second pair of eyes)<br />
<br />
This cheat-sheet is available in PDF form on a single side of A4 [http://wiki.makespace.org/File:TrainingCheatsheetUM2.pdf here].<br />
<br />
== Trained Users ==<br />
<br />
The following members of Makespace are trained and qualified to use the 3D Printer (note, they are not qualified to train others however):<br />
<br />
* Paul Osborn (Rob Voisey, 2015-07-30)<br />
* Julius Schmidt (Rob Voisey, 2015-07-30)<br />
* Peter Knight (Rob Voisey, 2015-07-30)<br />
* Adam Mulligan (Rob Voisey, 2015-07-30)<br />
* Charlotte Harvey (Rob Voisey, 2015-07-30)<br />
* Alex Gee (Rob Voisey, 2015-07-30)<br />
* Albert Santos (Rob Voisey, 2015-07-30)<br />
* Zizwani Mhango (Rob Voisey, 2015-07-30)<br />
* Christie Nel (Rob Voisey, 2015-07-30)<br />
* Robert Karpinski (Rob Voisey, 2015-07-30)<br />
* Alexis Mather (Stephen Harrison, 2015-08-03)<br />
* Ben Wheatley (Stephen Harrison, 2015-08-03)<br />
* Stevan Wing (Stephen Harrison, 2015-08-03)<br />
* Jae Tumer (Stephen Harrison, 2015-08-03)<br />
* Jennifer Herbert (Stephen Harrison, 2015-08-03)<br />
* Frodi Jones (Stephen Harrison, 2015-08-03)<br />
* Matt Wayland (Stephen Harrison, 2015-08-03)<br />
* Marco Aite (Stephen Harrison, 2015-08-03)<br />
* Graeham Douglas (Stephen Harrison, 2015-08-03)<br />
* Robin Sterling (Stephen Harrison, 2015-08-07)<br />
* Abhi Manyu (Stephen Harrison, 2015-08-07)<br />
* Ward Hills (Stephen Harrison, 2015-08-07)<br />
* Carols A. Lugo (Stephen Harrison, 2015-08-07)<br />
* Ben Alper (Stephen Harrison, 2015-08-07)<br />
* Jon Green (Stephen Harrison, 2015-08-07)<br />
* Marcin Izo (Stephen Harrison, 2015-08-07)<br />
* Steve Upton (Rob Voisey, 2015-08-11)<br />
* Frederic Sorgeloos (Rob Voisey, 2015-08-11)<br />
* Andrew Cooke (Rob Voisey, 2015-08-11)<br />
* Ned Booker (Rob Voisey, 2015-08-11)<br />
* Daryl Stewart (Paul Edgington, 2015-08-24)<br />
* Nacho Lopez (Paul Edgington, 2015-08-24)<br />
* Ed Robertson (Paul Edgington, 2015-08-24)<br />
* Clive Beale (Paul Edgington, 2015-08-24)<br />
* Oliver Fleck (Paul Edgington, 2015-08-24)<br />
* Mark Cheverton (Rob Voisey, 2015-09-08)<br />
* Nik (Rob Voisey, 2015-09-08)<br />
* Dan Tidhar (Rob Voisey, 2015-09-08)<br />
* Tobias Wenzel (Rob Voisey, 2015-09-08)<br />
* Brian Starkey (Rob Voisey, 2015-09-08)<br />
* Jonathan Waite (Rob Voisey, 2015-09-08)<br />
* Emyr James (Rob Voisey, 2015-09-08)<br />
* Richard Hall (Rob Voisey, 2015-09-08)<br />
* Andrew Dunn (Rob Voisey, 2015-09-08)<br />
* Andrea Cipri (Paul Edgington, 2015-09-30)<br />
* John Sidinopoulos (Paul Edgington, 2015-09-30)<br />
* Stuart Barton (Paul Edgington, 2015-09-30)<br />
* Mark Calleta (Paul Edgington, 2015-09-30)<br />
* Martin Lenz (Paul Edgington, 2015-09-30)<br />
* Phill Banks (Paul Edgington, 2015-10-21)<br />
* Felix Morley (Paul Edgington, 2015-10-21)<br />
* David Jordan (Paul Edgington, 2015-10-21)<br />
* Mark Roberts (Stephen Harrison, 2015-10-23)<br />
* Jenny Molloy (Stephen Harrison, 2015-10-23)<br />
* Henry Cawley (Rob Voisey, 2015-11-18)<br />
* Bogdan Spiridom (Rob Voisey, 2015-11-18)<br />
* Jakub Sanak (Rob Voisey, 2015-11-18)<br />
* Jack Brewster (Rob Voisey, 2015-11-18)<br />
* Mayke Santos (Rob Voisey, 2015-11-18)<br />
* Luis Veiga Pumar (Stephen Harrison, 2015-11-24)<br />
* Greg Matthews (Stephen Harrison, 2015-11-24)<br />
* Brian Corteil (Stephen Harrison, 2015-11-24)<br />
* Rob Rescorla (Stephen Harrison, 2015-11-24)<br />
* Leo Rones (Stephen Harrison, 2015-11-24)<br />
* Diana Probst (Stephen Harrison, 2015-11-25)<br />
* Adrian van den Heever (Stephen Harrison, 2015-11-25)<br />
* Al Napp (Stephen Harrison, 2015-11-25)<br />
* Katy Marshall (Stephen Harrison, 2015-12-01)<br />
* Peter Mottram (Stephen Harrison, 2015-12-01)<br />
* David Barham (Stephen Harrison, 2015-12-01)<br />
* Johan Henriksson (Stephen Harrison, 2015-12-01)<br />
* Fotis Fotiadis (Stephen Harrison, 2015-12-01)<br />
* Oliver Martin (Stephen Harrison, 2015-12-01)<br />
* Andrew Drummond (Stephen Harrison, 2015-12-01)<br />
* Spencer Dixon (Stephen Harrison, 2015-12-01)<br />
* Jonathan Woolf (Rob Voisey, 2016-01-07)<br />
* Daniel Bailey (Rob Voisey, 2016-01-07)<br />
* David Haines (Rob Voisey, 2016-01-07)<br />
* Giovanni Bisutii (Rob Voisey, 2016-01-07)<br />
* Simon Hartley (Daniel Bailey, 2016-02-11)<br />
* Francois Eve (Daniel Bailey, 2016-02-11)<br />
* Giovanni Orlando (Daniel Bailey, 2016-02-11)<br />
* Dan Tidhar (Daniel Bailey, 2016-02-11)<br />
* Shunsuke Fujibayashi (Daniel Bailey, 2016-03-04)<br />
* Ronny Schlutter (Daniel Bailey, 2016-03-04)<br />
* Jamie Powell (Daniel Bailey, 2016-03-04)<br />
* Mark Wainwright (Daniel Bailey, 2016-03-04)<br />
* Charna Hume (Daniel Bailey, 2016-03-04)<br />
* Charlotte Godley (Daniel Bailey, 2016-03-04)<br />
* Jose Chitty (Stephen Harrison, 2016-03-22)<br />
* Mat Greenwood (Stephen Harrison, 2016-03-22)<br />
* David Fisher (Stephen Harrison, 2016-03-22)<br />
* Tom Kelly (Stephen Harrison, 2016-03-22)<br />
* David Bebb (Stephen Harrison, 2016-04-12)<br />
* David Taylor (Stephen Harrison, 2016-04-12)<br />
* Jo Brook (Stephen Harrison, 2016-04-12)<br />
* Craig Easton (Daniel Bailey, 2016-04-20)<br />
* James Griffiths (Daniel Bailey, 2016-04-20)<br />
* Paul Routley (Daniel Bailey, 2016-04-20)<br />
* Steve Murphy (Daniel Bailey, 2016-04-20)<br />
* Cong Cong Bo (Daniel Bailey, 2016-06-24)<br />
* Adrien Leger (Daniel Bailey, 2016-06-24)<br />
* David Marcus (Daniel Bailey, 2016-06-24)<br />
* Mik Lamming (Stephen Harrison, 2016-07-06)<br />
* Rob MacAulay (Stephen Harrison, 2016-07-06)<br />
* Daniel Farrant (Stephen Harrison, 2016-07-06)<br />
* Steve Carey (Stephen Harrison, 2016-07-06)<br />
* Debora Rodriguez (Daniel Bailey, 2016-07-30)<br />
* David Horsnell (Daniel Bailey, 2016-07-30)<br />
* Cat Fitzpatrick (Daniel Bailey, 2016-08-12)<br />
* Hsingling Lian (Daniel Bailey, 2016-08-12)<br />
* Jeremy Bentham (Daniel Bailey, 2016-08-12)<br />
* Nadia Bassiri (Daniel Bailey, 2016-08-12)<br />
* Thomas Wanger (Daniel Bailey, 2016-08-12)</div>Danieljabaileyhttp://wiki.makespace.org/Equipment/3D_Printer/UM2TrainingEquipment/3D Printer/UM2Training2016-07-30T19:40:11Z<p>Danieljabailey: /* Trained Users */ Added users trained 2016-07-30</p>
<hr />
<div>[[Equipment|Equipment]] / [[Equipment/3D Printer|UM2]] / Training<br />
<br />
= Ultimaker 2 3D Printer Training =<br />
<br />
This page documents the process for being trained on the Ultimaker 2 Printer, and the list of members who have completed that training.<br />
<br />
== Summary ==<br />
<br />
Training takes place in three main steps:<br />
* Group Training of 1-4 members, going through the equipment and how to use it (~1hr)<br />
* Individual Training Task, where an individual member is set a task to complete to prove and improve understanding (~20min each)<br />
* Recommended project oversight, where more experienced users oversee the projects being undertaken when cutting (first 2-3 projects)<br />
<br />
A shorter conversion training session is available for members who were previously signed off to use the Makerbot 2X printer. These sessions last around 20 minutes and do not include individual sessions.<br />
<br />
== Booking ==<br />
<br />
For discussing and arranging slots, please use the mailing list. New training sessions will be announced on the Meetup group.<br />
<br />
Notes:<br />
* You can only be trained if you have RSVP'd to a Meetup session<br />
<br />
== Training Cheatsheet - Conversion Course ==<br />
<br />
Members already trained on and familiar with the Makerbot 2X can attend this short conversion course to be signed off to use the Ultimaker 2 3D printer. Up to 10 people can be accommodated on each course, which lasts 20 to 30 minutes.<br />
<br />
1. Physical Differences from the 2X<br />
* Glass build plate, no kapton tape<br />
* Single extruder<br />
* Push feed<br />
<br />
2. General<br />
* Use the correct filament (2.85mm, NOT 3mm or 1.75mm)<br />
* New filament storage system<br />
<br />
3. Printing<br />
* Fence / Brim / Raft<br />
* OK to leave printer unattended after the first few layers<br />
* Camera available for remote monitoring<br />
* Use only plastic implements for part removal, take care not to melt them on the hot end<br />
<br />
4. Cura Software<br />
* Import and place<br />
* Simple mode<br />
* Brief overview of advanced mode<br />
* Temperature set on printer not slicer<br />
* Exporting to SD card<br />
<br />
5. Unload / Load filament<br />
* How to feed (slow first, then fast)<br />
* Select correct material in menu<br />
* Changing temperature and speed parameters from printer<br />
* Demonstrate the atomic method of cleaning the extruder to prevent feed jams<br />
<br />
6. Filament pricing<br />
* 5p per gram for PLA and ABS, to be kept under review<br />
* Include wastage!<br />
<br />
== Training Cheatsheet - Full Course ==<br />
<br />
'''Group Session'''<br />
<br />
1. Ask what each member hopes to get out of the 3D printer.<br />
<br />
2. Explain how 3D printing works<br />
<br />
3. Safety<br />
* Burn hazard – nozzle and build plate<br />
* Unit may move unexpectedly<br />
* Avoid prolonged exposure to ABS fumes<br />
<br />
4. Damage to machine<br />
* Fragile build plate<br />
* Jammed filament<br />
<br />
5. General<br />
* Use the correct filament (2.85mm)<br />
* Filament storage and feed system<br />
* Switch off when finished<br />
* Leave levelling to the owners but report any problems<br />
<br />
6. PLA vs ABS<br />
* How to tell the difference<br />
* Different temperature<br />
* PLA Biodegradable<br />
<br />
7. Software / workflow<br />
* Importing<br />
* Positioning on bed<br />
* Supports<br />
* Setting quality / speed trade off<br />
* Advanced options<br />
* Exporting to SD card<br />
<br />
8. Unload / load<br />
* Attaching spool or loading from storage box<br />
* Feeding (slow then fast)<br />
* Beware of wrapping round axle<br />
* Setting material in menu<br />
* Adjusting parameters, e.g. ABS plate temperature<br />
<br />
9. Printing<br />
* Preheating<br />
* Fence printing<br />
* Keep an eye on progress, locally or with camera<br />
* If leaving unattended, put a post-it with your contact details<br />
* Use only plastic implements for part removal<br />
<br />
10. Other stuff<br />
* Demonstrate atomic method of cleaning the nozzle to prevent feed jams<br />
* Strength characteristics – orientation is important<br />
* Paying<br />
<br />
'''Individual Training Task'''<br />
<br />
Task<br />
* Should demonstrate import, setup, position and run<br />
* Choose a part that takes about 10 mins to print (preloaded on PC)<br />
<br />
Steps<br />
* Set individual to work, don't prompt but do answer questions (or pose if needed)<br />
* Talk through design once done, question/check things etc<br />
* Proceed to printing (watch carefully all steps)<br />
<br />
Assuming all ok:<br />
* Get them to read the health and safety notes about operation and materials<br />
* Add to the trained member list<br />
<br />
'''Project Oversight'''<br />
<br />
For next 2-3 projects, recommend member will find another more experienced trained user to support them (second pair of eyes)<br />
<br />
This cheat-sheet is available in PDF form on a single side of A4 [http://wiki.makespace.org/File:TrainingCheatsheetUM2.pdf here].<br />
<br />
== Trained Users ==<br />
<br />
The following members of Makespace are trained and qualified to use the 3D Printer (note, they are not qualified to train others however):<br />
<br />
* Paul Osborn (Rob Voisey, 2015-07-30)<br />
* Julius Schmidt (Rob Voisey, 2015-07-30)<br />
* Peter Knight (Rob Voisey, 2015-07-30)<br />
* Adam Mulligan (Rob Voisey, 2015-07-30)<br />
* Charlotte Harvey (Rob Voisey, 2015-07-30)<br />
* Alex Gee (Rob Voisey, 2015-07-30)<br />
* Albert Santos (Rob Voisey, 2015-07-30)<br />
* Zizwani Mhango (Rob Voisey, 2015-07-30)<br />
* Christie Nel (Rob Voisey, 2015-07-30)<br />
* Robert Karpinski (Rob Voisey, 2015-07-30)<br />
* Alexis Mather (Stephen Harrison, 2015-08-03)<br />
* Ben Wheatley (Stephen Harrison, 2015-08-03)<br />
* Stevan Wing (Stephen Harrison, 2015-08-03)<br />
* Jae Tumer (Stephen Harrison, 2015-08-03)<br />
* Jennifer Herbert (Stephen Harrison, 2015-08-03)<br />
* Frodi Jones (Stephen Harrison, 2015-08-03)<br />
* Matt Wayland (Stephen Harrison, 2015-08-03)<br />
* Marco Aite (Stephen Harrison, 2015-08-03)<br />
* Graeham Douglas (Stephen Harrison, 2015-08-03)<br />
* Robin Sterling (Stephen Harrison, 2015-08-07)<br />
* Abhi Manyu (Stephen Harrison, 2015-08-07)<br />
* Ward Hills (Stephen Harrison, 2015-08-07)<br />
* Carols A. Lugo (Stephen Harrison, 2015-08-07)<br />
* Ben Alper (Stephen Harrison, 2015-08-07)<br />
* Jon Green (Stephen Harrison, 2015-08-07)<br />
* Marcin Izo (Stephen Harrison, 2015-08-07)<br />
* Steve Upton (Rob Voisey, 2015-08-11)<br />
* Frederic Sorgeloos (Rob Voisey, 2015-08-11)<br />
* Andrew Cooke (Rob Voisey, 2015-08-11)<br />
* Ned Booker (Rob Voisey, 2015-08-11)<br />
* Daryl Stewart (Paul Edgington, 2015-08-24)<br />
* Nacho Lopez (Paul Edgington, 2015-08-24)<br />
* Ed Robertson (Paul Edgington, 2015-08-24)<br />
* Clive Beale (Paul Edgington, 2015-08-24)<br />
* Oliver Fleck (Paul Edgington, 2015-08-24)<br />
* Mark Cheverton (Rob Voisey, 2015-09-08)<br />
* Nik (Rob Voisey, 2015-09-08)<br />
* Dan Tidhar (Rob Voisey, 2015-09-08)<br />
* Tobias Wenzel (Rob Voisey, 2015-09-08)<br />
* Brian Starkey (Rob Voisey, 2015-09-08)<br />
* Jonathan Waite (Rob Voisey, 2015-09-08)<br />
* Emyr James (Rob Voisey, 2015-09-08)<br />
* Richard Hall (Rob Voisey, 2015-09-08)<br />
* Andrew Dunn (Rob Voisey, 2015-09-08)<br />
* Andrea Cipri (Paul Edgington, 2015-09-30)<br />
* John Sidinopoulos (Paul Edgington, 2015-09-30)<br />
* Stuart Barton (Paul Edgington, 2015-09-30)<br />
* Mark Calleta (Paul Edgington, 2015-09-30)<br />
* Martin Lenz (Paul Edgington, 2015-09-30)<br />
* Phill Banks (Paul Edgington, 2015-10-21)<br />
* Felix Morley (Paul Edgington, 2015-10-21)<br />
* David Jordan (Paul Edgington, 2015-10-21)<br />
* Mark Roberts (Stephen Harrison, 2015-10-23)<br />
* Jenny Molloy (Stephen Harrison, 2015-10-23)<br />
* Henry Cawley (Rob Voisey, 2015-11-18)<br />
* Bogdan Spiridom (Rob Voisey, 2015-11-18)<br />
* Jakub Sanak (Rob Voisey, 2015-11-18)<br />
* Jack Brewster (Rob Voisey, 2015-11-18)<br />
* Mayke Santos (Rob Voisey, 2015-11-18)<br />
* Luis Veiga Pumar (Stephen Harrison, 2015-11-24)<br />
* Greg Matthews (Stephen Harrison, 2015-11-24)<br />
* Brian Corteil (Stephen Harrison, 2015-11-24)<br />
* Rob Rescorla (Stephen Harrison, 2015-11-24)<br />
* Leo Rones (Stephen Harrison, 2015-11-24)<br />
* Diana Probst (Stephen Harrison, 2015-11-25)<br />
* Adrian van den Heever (Stephen Harrison, 2015-11-25)<br />
* Al Napp (Stephen Harrison, 2015-11-25)<br />
* Katy Marshall (Stephen Harrison, 2015-12-01)<br />
* Peter Mottram (Stephen Harrison, 2015-12-01)<br />
* David Barham (Stephen Harrison, 2015-12-01)<br />
* Johan Henriksson (Stephen Harrison, 2015-12-01)<br />
* Fotis Fotiadis (Stephen Harrison, 2015-12-01)<br />
* Oliver Martin (Stephen Harrison, 2015-12-01)<br />
* Andrew Drummond (Stephen Harrison, 2015-12-01)<br />
* Spencer Dixon (Stephen Harrison, 2015-12-01)<br />
* Jonathan Woolf (Rob Voisey, 2016-01-07)<br />
* Daniel Bailey (Rob Voisey, 2016-01-07)<br />
* David Haines (Rob Voisey, 2016-01-07)<br />
* Giovanni Bisutii (Rob Voisey, 2016-01-07)<br />
* Simon Hartley (Daniel Bailey, 2016-02-11)<br />
* Francois Eve (Daniel Bailey, 2016-02-11)<br />
* Giovanni Orlando (Daniel Bailey, 2016-02-11)<br />
* Dan Tidhar (Daniel Bailey, 2016-02-11)<br />
* Shunsuke Fujibayashi (Daniel Bailey, 2016-03-04)<br />
* Ronny Schlutter (Daniel Bailey, 2016-03-04)<br />
* Jamie Powell (Daniel Bailey, 2016-03-04)<br />
* Mark Wainwright (Daniel Bailey, 2016-03-04)<br />
* Charna Hume (Daniel Bailey, 2016-03-04)<br />
* Charlotte Godley (Daniel Bailey, 2016-03-04)<br />
* Jose Chitty (Stephen Harrison, 2016-03-22)<br />
* Mat Greenwood (Stephen Harrison, 2016-03-22)<br />
* David Fisher (Stephen Harrison, 2016-03-22)<br />
* Tom Kelly (Stephen Harrison, 2016-03-22)<br />
* David Bebb (Stephen Harrison, 2016-04-12)<br />
* David Taylor (Stephen Harrison, 2016-04-12)<br />
* Jo Brook (Stephen Harrison, 2016-04-12)<br />
* Craig Easton (Daniel Bailey, 2016-04-20)<br />
* James Griffiths (Daniel Bailey, 2016-04-20)<br />
* Paul Routley (Daniel Bailey, 2016-04-20)<br />
* Steve Murphy (Daniel Bailey, 2016-04-20)<br />
* Cong Cong Bo (Daniel Bailey, 2016-06-24)<br />
* Adrien Leger (Daniel Bailey, 2016-06-24)<br />
* David Marcus (Daniel Bailey, 2016-06-24)<br />
* Mik Lamming (Stephen Harrison, 2016-07-06)<br />
* Rob MacAulay (Stephen Harrison, 2016-07-06)<br />
* Daniel Farrant (Stephen Harrison, 2016-07-06)<br />
* Steve Carey (Stephen Harrison, 2016-07-06)<br />
* Debora Rodriguez (Daniel Bailey, 2016-07-30)<br />
* David Horsnell (Daniel Bailey, 2016-07-30)</div>Danieljabaileyhttp://wiki.makespace.org/Equipment/3D_Printer/UM2TrainingEquipment/3D Printer/UM2Training2016-06-24T20:27:36Z<p>Danieljabailey: /* Trained Users */ Added users trained 2016-06-24</p>
<hr />
<div>[[Equipment|Equipment]] / [[Equipment/3D Printer|UM2]] / Training<br />
<br />
= Ultimaker 2 3D Printer Training =<br />
<br />
This page documents the process for being trained on the Ultimaker 2 Printer, and the list of members who have completed that training.<br />
<br />
== Summary ==<br />
<br />
Training takes place in three main steps:<br />
* Group Training of 1-4 members, going through the equipment and how to use it (~1hr)<br />
* Individual Training Task, where an individual member is set a task to complete to prove and improve understanding (~20min each)<br />
* Recommended project oversight, where more experienced users oversee the projects being undertaken when cutting (first 2-3 projects)<br />
<br />
A shorter conversion training session is available for members who were previously signed off to use the Makerbot 2X printer. These sessions last around 20 minutes and do not include individual sessions.<br />
<br />
== Booking ==<br />
<br />
For discussing and arranging slots, please use the mailing list. New training sessions will be announced on the Meetup group.<br />
<br />
Notes:<br />
* You can only be trained if you have RSVP'd to a Meetup session<br />
<br />
== Training Cheatsheet - Conversion Course ==<br />
<br />
Members already trained on and familiar with the Makerbot 2X can attend this short conversion course to be signed off to use the Ultimaker 2 3D printer. Up to 10 people can be accommodated on each course, which lasts 20 to 30 minutes.<br />
<br />
1. Physical Differences from the 2X<br />
* Glass build plate, no kapton tape<br />
* Single extruder<br />
* Push feed<br />
<br />
2. General<br />
* Use the correct filament (2.85mm, NOT 3mm or 1.75mm)<br />
* New filament storage system<br />
<br />
3. Printing<br />
* Fence / Brim / Raft<br />
* OK to leave printer unattended after the first few layers<br />
* Camera available for remote monitoring<br />
* Use only plastic implements for part removal, take care not to melt them on the hot end<br />
<br />
4. Cura Software<br />
* Import and place<br />
* Simple mode<br />
* Brief overview of advanced mode<br />
* Temperature set on printer not slicer<br />
* Exporting to SD card<br />
<br />
5. Unload / Load filament<br />
* How to feed (slow first, then fast)<br />
* Select correct material in menu<br />
* Changing temperature and speed parameters from printer<br />
* Demonstrate the atomic method of cleaning the extruder to prevent feed jams<br />
<br />
6. Filament pricing<br />
* 5p per gram for PLA and ABS, to be kept under review<br />
* Include wastage!<br />
<br />
== Training Cheatsheet - Full Course ==<br />
<br />
'''Group Session'''<br />
<br />
1. Ask what each member hopes to get out of the 3D printer.<br />
<br />
2. Explain how 3D printing works<br />
<br />
3. Safety<br />
* Burn hazard – nozzle and build plate<br />
* Unit may move unexpectedly<br />
* Avoid prolonged exposure to ABS fumes<br />
<br />
4. Damage to machine<br />
* Fragile build plate<br />
* Jammed filament<br />
<br />
5. General<br />
* Use the correct filament (2.85mm)<br />
* Filament storage and feed system<br />
* Switch off when finished<br />
* Leave levelling to the owners but report any problems<br />
<br />
6. PLA vs ABS<br />
* How to tell the difference<br />
* Different temperature<br />
* PLA Biodegradable<br />
<br />
7. Software / workflow<br />
* Importing<br />
* Positioning on bed<br />
* Supports<br />
* Setting quality / speed trade off<br />
* Advanced options<br />
* Exporting to SD card<br />
<br />
8. Unload / load<br />
* Attaching spool or loading from storage box<br />
* Feeding (slow then fast)<br />
* Beware of wrapping round axle<br />
* Setting material in menu<br />
* Adjusting parameters, e.g. ABS plate temperature<br />
<br />
9. Printing<br />
* Preheating<br />
* Fence printing<br />
* Keep an eye on progress, locally or with camera<br />
* If leaving unattended, put a post-it with your contact details<br />
* Use only plastic implements for part removal<br />
<br />
10. Other stuff<br />
* Demonstrate atomic method of cleaning the nozzle to prevent feed jams<br />
* Strength characteristics – orientation is important<br />
* Paying<br />
<br />
'''Individual Training Task'''<br />
<br />
Task<br />
* Should demonstrate import, setup, position and run<br />
* Choose a part that takes about 10 mins to print (preloaded on PC)<br />
<br />
Steps<br />
* Set individual to work, don't prompt but do answer questions (or pose if needed)<br />
* Talk through design once done, question/check things etc<br />
* Proceed to printing (watch carefully all steps)<br />
<br />
Assuming all ok:<br />
* Get them to read the health and safety notes about operation and materials<br />
* Add to the trained member list<br />
<br />
'''Project Oversight'''<br />
<br />
For next 2-3 projects, recommend member will find another more experienced trained user to support them (second pair of eyes)<br />
<br />
This cheat-sheet is available in PDF form on a single side of A4 [http://wiki.makespace.org/File:TrainingCheatsheetUM2.pdf here].<br />
<br />
== Trained Users ==<br />
<br />
The following members of Makespace are trained and qualified to use the 3D Printer (note, they are not qualified to train others however):<br />
<br />
* Paul Osborn (Rob Voisey, 2015-07-30)<br />
* Julius Schmidt (Rob Voisey, 2015-07-30)<br />
* Peter Knight (Rob Voisey, 2015-07-30)<br />
* Adam Mulligan (Rob Voisey, 2015-07-30)<br />
* Charlotte Harvey (Rob Voisey, 2015-07-30)<br />
* Alex Gee (Rob Voisey, 2015-07-30)<br />
* Albert Santos (Rob Voisey, 2015-07-30)<br />
* Zizwani Mhango (Rob Voisey, 2015-07-30)<br />
* Christie Nel (Rob Voisey, 2015-07-30)<br />
* Robert Karpinski (Rob Voisey, 2015-07-30)<br />
* Alexis Mather (Stephen Harrison, 2015-08-03)<br />
* Ben Wheatley (Stephen Harrison, 2015-08-03)<br />
* Stevan Wing (Stephen Harrison, 2015-08-03)<br />
* Jae Tumer (Stephen Harrison, 2015-08-03)<br />
* Jennifer Herbert (Stephen Harrison, 2015-08-03)<br />
* Frodi Jones (Stephen Harrison, 2015-08-03)<br />
* Matt Wayland (Stephen Harrison, 2015-08-03)<br />
* Marco Aite (Stephen Harrison, 2015-08-03)<br />
* Graeham Douglas (Stephen Harrison, 2015-08-03)<br />
* Robin Sterling (Stephen Harrison, 2015-08-07)<br />
* Abhi Manyu (Stephen Harrison, 2015-08-07)<br />
* Ward Hills (Stephen Harrison, 2015-08-07)<br />
* Carols A. Lugo (Stephen Harrison, 2015-08-07)<br />
* Ben Alper (Stephen Harrison, 2015-08-07)<br />
* Jon Green (Stephen Harrison, 2015-08-07)<br />
* Marcin Izo (Stephen Harrison, 2015-08-07)<br />
* Steve Upton (Rob Voisey, 2015-08-11)<br />
* Frederic Sorgeloos (Rob Voisey, 2015-08-11)<br />
* Andrew Cooke (Rob Voisey, 2015-08-11)<br />
* Ned Booker (Rob Voisey, 2015-08-11)<br />
* Daryl Stewart (Paul Edgington, 2015-08-24)<br />
* Nacho Lopez (Paul Edgington, 2015-08-24)<br />
* Ed Robertson (Paul Edgington, 2015-08-24)<br />
* Clive Beale (Paul Edgington, 2015-08-24)<br />
* Oliver Fleck (Paul Edgington, 2015-08-24)<br />
* Mark Cheverton (Rob Voisey, 2015-09-08)<br />
* Nik (Rob Voisey, 2015-09-08)<br />
* Dan Tidhar (Rob Voisey, 2015-09-08)<br />
* Tobias Wenzel (Rob Voisey, 2015-09-08)<br />
* Brian Starkey (Rob Voisey, 2015-09-08)<br />
* Jonathan Waite (Rob Voisey, 2015-09-08)<br />
* Emyr James (Rob Voisey, 2015-09-08)<br />
* Richard Hall (Rob Voisey, 2015-09-08)<br />
* Andrew Dunn (Rob Voisey, 2015-09-08)<br />
* Andrea Cipri (Paul Edgington, 2015-09-30)<br />
* John Sidinopoulos (Paul Edgington, 2015-09-30)<br />
* Stuart Barton (Paul Edgington, 2015-09-30)<br />
* Mark Calleta (Paul Edgington, 2015-09-30)<br />
* Martin Lenz (Paul Edgington, 2015-09-30)<br />
* Phill Banks (Paul Edgington, 2015-10-21)<br />
* Felix Morley (Paul Edgington, 2015-10-21)<br />
* David Jordan (Paul Edgington, 2015-10-21)<br />
* Mark Roberts (Stephen Harrison, 2015-10-23)<br />
* Jenny Molloy (Stephen Harrison, 2015-10-23)<br />
* Henry Cawley (Rob Voisey, 2015-11-18)<br />
* Bogdan Spiridom (Rob Voisey, 2015-11-18)<br />
* Jakub Sanak (Rob Voisey, 2015-11-18)<br />
* Jack Brewster (Rob Voisey, 2015-11-18)<br />
* Mayke Santos (Rob Voisey, 2015-11-18)<br />
* Luis Veiga Pumar (Stephen Harrison, 2015-11-24)<br />
* Greg Matthews (Stephen Harrison, 2015-11-24)<br />
* Brian Corteil (Stephen Harrison, 2015-11-24)<br />
* Rob Rescorla (Stephen Harrison, 2015-11-24)<br />
* Leo Rones (Stephen Harrison, 2015-11-24)<br />
* Diana Probst (Stephen Harrison, 2015-11-25)<br />
* Adrian van den Heever (Stephen Harrison, 2015-11-25)<br />
* Al Napp (Stephen Harrison, 2015-11-25)<br />
* Katy Marshall (Stephen Harrison, 2015-12-01)<br />
* Peter Mottram (Stephen Harrison, 2015-12-01)<br />
* David Barham (Stephen Harrison, 2015-12-01)<br />
* Johan Henriksson (Stephen Harrison, 2015-12-01)<br />
* Fotis Fotiadis (Stephen Harrison, 2015-12-01)<br />
* Oliver Martin (Stephen Harrison, 2015-12-01)<br />
* Andrew Drummond (Stephen Harrison, 2015-12-01)<br />
* Spencer Dixon (Stephen Harrison, 2015-12-01)<br />
* Jonathan Woolf (Rob Voisey, 2016-01-07)<br />
* Daniel Bailey (Rob Voisey, 2016-01-07)<br />
* David Haines (Rob Voisey, 2016-01-07)<br />
* Giovanni Bisutii (Rob Voisey, 2016-01-07)<br />
* Simon Hartley (Daniel Bailey, 2016-02-11)<br />
* Francois Eve (Daniel Bailey, 2016-02-11)<br />
* Giovanni Orlando (Daniel Bailey, 2016-02-11)<br />
* Dan Tidhar (Daniel Bailey, 2016-02-11)<br />
* Shunsuke Fujibayashi (Daniel Bailey, 2016-03-04)<br />
* Ronny Schlutter (Daniel Bailey, 2016-03-04)<br />
* Jamie Powell (Daniel Bailey, 2016-03-04)<br />
* Mark Wainwright (Daniel Bailey, 2016-03-04)<br />
* Charna Hume (Daniel Bailey, 2016-03-04)<br />
* Charlotte Godley (Daniel Bailey, 2016-03-04)<br />
* Jose Chitty (Stephen Harrison, 2016-03-22)<br />
* Mat Greenwood (Stephen Harrison, 2016-03-22)<br />
* David Fisher (Stephen Harrison, 2016-03-22)<br />
* Tom Kelly (Stephen Harrison, 2016-03-22)<br />
* David Bebb (Stephen Harrison, 2016-04-12)<br />
* David Taylor (Stephen Harrison, 2016-04-12)<br />
* Jo Brook (Stephen Harrison, 2016-04-12)<br />
* Craig Easton (Daniel Bailey, 2016-04-20)<br />
* James Griffiths (Daniel Bailey, 2016-04-20)<br />
* Paul Routley (Daniel Bailey, 2016-04-20)<br />
* Steve Murphy (Daniel Bailey, 2016-04-20)<br />
* Cong Cong Bo (Daniel Bailey, 2016-06-24)<br />
* Adrien Leger (Daniel Bailey, 2016-06-24)<br />
* David Marcus (Daniel Bailey, 2016-06-24)</div>Danieljabaileyhttp://wiki.makespace.org/Equipment/3D_Printer/UM2TrainingEquipment/3D Printer/UM2Training2016-04-20T21:25:52Z<p>Danieljabailey: /* Trained Users */ update name</p>
<hr />
<div>[[Equipment|Equipment]] / [[Equipment/3D Printer|UM2]] / Training<br />
<br />
= Ultimaker 2 3D Printer Training =<br />
<br />
This page documents the process for being trained on the Ultimaker 2 Printer, and the list of members who have completed that training.<br />
<br />
== Summary ==<br />
<br />
Training takes place in three main steps:<br />
* Group Training of 1-4 members, going through the equipment and how to use it (~1hr)<br />
* Individual Training Task, where an individual member is set a task to complete to prove and improve understanding (~20min each)<br />
* Recommended project oversight, where more experienced users oversee the projects being undertaken when cutting (first 2-3 projects)<br />
<br />
A shorter conversion training session is available for members who were previously signed off to use the Makerbot 2X printer. These sessions last around 20 minutes and do not include individual sessions.<br />
<br />
== Booking ==<br />
<br />
For discussing and arranging slots, please use the mailing list. New training sessions will be announced on the Meetup group.<br />
<br />
Notes:<br />
* You can only be trained if you have RSVP'd to a Meetup session<br />
<br />
== Training Cheatsheet - Conversion Course ==<br />
<br />
Members already trained on and familiar with the Makerbot 2X can attend this short conversion course to be signed off to use the Ultimaker 2 3D printer. Up to 10 people can be accommodated on each course, which lasts 20 to 30 minutes.<br />
<br />
1. Physical Differences from the 2X<br />
* Glass build plate, no kapton tape<br />
* Single extruder<br />
* Push feed<br />
<br />
2. General<br />
* Use the correct filament (2.85mm, NOT 3mm or 1.75mm)<br />
* New filament storage system<br />
<br />
3. Printing<br />
* Fence / Brim / Raft<br />
* OK to leave printer unattended after the first few layers<br />
* Camera available for remote monitoring<br />
* Use only plastic implements for part removal, take care not to melt them on the hot end<br />
<br />
4. Cura Software<br />
* Import and place<br />
* Simple mode<br />
* Brief overview of advanced mode<br />
* Temperature set on printer not slicer<br />
* Exporting to SD card<br />
<br />
5. Unload / Load filament<br />
* How to feed (slow first, then fast)<br />
* Select correct material in menu<br />
* Changing temperature and speed parameters from printer<br />
* Demonstrate the atomic method of cleaning the extruder to prevent feed jams<br />
<br />
6. Filament pricing<br />
* 5p per gram for PLA and ABS, to be kept under review<br />
* Include wastage!<br />
<br />
== Training Cheatsheet - Full Course ==<br />
<br />
'''Group Session'''<br />
<br />
1. Ask what each member hopes to get out of the 3D printer.<br />
<br />
2. Explain how 3D printing works<br />
<br />
3. Safety<br />
* Burn hazard – nozzle and build plate<br />
* Unit may move unexpectedly<br />
* Avoid prolonged exposure to ABS fumes<br />
<br />
4. Damage to machine<br />
* Fragile build plate<br />
* Jammed filament<br />
<br />
5. General<br />
* Use the correct filament (2.85mm)<br />
* Filament storage and feed system<br />
* Switch off when finished<br />
* Leave levelling to the owners but report any problems<br />
<br />
6. PLA vs ABS<br />
* How to tell the difference<br />
* Different temperature<br />
* PLA Biodegradable<br />
<br />
7. Software / workflow<br />
* Importing<br />
* Positioning on bed<br />
* Supports<br />
* Setting quality / speed trade off<br />
* Advanced options<br />
* Exporting to SD card<br />
<br />
8. Unload / load<br />
* Attaching spool or loading from storage box<br />
* Feeding (slow then fast)<br />
* Beware of wrapping round axle<br />
* Setting material in menu<br />
* Adjusting parameters, e.g. ABS plate temperature<br />
<br />
9. Printing<br />
* Preheating<br />
* Fence printing<br />
* Keep an eye on progress, locally or with camera<br />
* If leaving unattended, put a post-it with your contact details<br />
* Use only plastic implements for part removal<br />
<br />
10. Other stuff<br />
* Demonstrate atomic method of cleaning the nozzle to prevent feed jams<br />
* Strength characteristics – orientation is important<br />
* Paying<br />
<br />
'''Individual Training Task'''<br />
<br />
Task<br />
* Should demonstrate import, setup, position and run<br />
* Choose a part that takes about 10 mins to print (preloaded on PC)<br />
<br />
Steps<br />
* Set individual to work, don't prompt but do answer questions (or pose if needed)<br />
* Talk through design once done, question/check things etc<br />
* Proceed to printing (watch carefully all steps)<br />
<br />
Assuming all ok:<br />
* Get them to read the health and safety notes about operation and materials<br />
* Add to the trained member list<br />
<br />
'''Project Oversight'''<br />
<br />
For next 2-3 projects, recommend member will find another more experienced trained user to support them (second pair of eyes)<br />
<br />
This cheat-sheet is available in PDF form on a single side of A4 [http://wiki.makespace.org/File:TrainingCheatsheetUM2.pdf here].<br />
<br />
== Trained Users ==<br />
<br />
The following members of Makespace are trained and qualified to use the 3D Printer (note, they are not qualified to train others however):<br />
<br />
* Paul Osborn (Rob Voisey, 2015-07-30)<br />
* Julius Schmidt (Rob Voisey, 2015-07-30)<br />
* Peter Knight (Rob Voisey, 2015-07-30)<br />
* Adam Mulligan (Rob Voisey, 2015-07-30)<br />
* Charlotte Harvey (Rob Voisey, 2015-07-30)<br />
* Alex Gee (Rob Voisey, 2015-07-30)<br />
* Albert Santos (Rob Voisey, 2015-07-30)<br />
* Zizwani Mhango (Rob Voisey, 2015-07-30)<br />
* Christie Nel (Rob Voisey, 2015-07-30)<br />
* Robert Karpinski (Rob Voisey, 2015-07-30)<br />
* Alexis Mather (Stephen Harrison, 2015-08-03)<br />
* Ben Wheatley (Stephen Harrison, 2015-08-03)<br />
* Stevan Wing (Stephen Harrison, 2015-08-03)<br />
* Jae Tumer (Stephen Harrison, 2015-08-03)<br />
* Jennifer Herbert (Stephen Harrison, 2015-08-03)<br />
* Frodi Jones (Stephen Harrison, 2015-08-03)<br />
* Matt Wayland (Stephen Harrison, 2015-08-03)<br />
* Marco Aite (Stephen Harrison, 2015-08-03)<br />
* Graeham Douglas (Stephen Harrison, 2015-08-03)<br />
* Robin Sterling (Stephen Harrison, 2015-08-07)<br />
* Abhi Manyu (Stephen Harrison, 2015-08-07)<br />
* Ward Hills (Stephen Harrison, 2015-08-07)<br />
* Carols A. Lugo (Stephen Harrison, 2015-08-07)<br />
* Ben Alper (Stephen Harrison, 2015-08-07)<br />
* Jon Green (Stephen Harrison, 2015-08-07)<br />
* Marcin Izo (Stephen Harrison, 2015-08-07)<br />
* Steve Upton (Rob Voisey, 2015-08-11)<br />
* Frederic Sorgeloos (Rob Voisey, 2015-08-11)<br />
* Andrew Cooke (Rob Voisey, 2015-08-11)<br />
* Ned Booker (Rob Voisey, 2015-08-11)<br />
* Daryl Stewart (Paul Edgington, 2015-08-24)<br />
* Nacho Lopez (Paul Edgington, 2015-08-24)<br />
* Ed Robertson (Paul Edgington, 2015-08-24)<br />
* Clive Beale (Paul Edgington, 2015-08-24)<br />
* Oliver Fleck (Paul Edgington, 2015-08-24)<br />
* Mark Cheverton (Rob Voisey, 2015-09-08)<br />
* Nik (Rob Voisey, 2015-09-08)<br />
* Dan Tidhar (Rob Voisey, 2015-09-08)<br />
* Tobias Wenzel (Rob Voisey, 2015-09-08)<br />
* Brian Starkey (Rob Voisey, 2015-09-08)<br />
* Jonathan Waite (Rob Voisey, 2015-09-08)<br />
* Emyr James (Rob Voisey, 2015-09-08)<br />
* Richard Hall (Rob Voisey, 2015-09-08)<br />
* Andrew Dunn (Rob Voisey, 2015-09-08)<br />
* Andrea Cipri (Paul Edgington, 2015-09-30)<br />
* John Sidinopoulos (Paul Edgington, 2015-09-30)<br />
* Stuart Barton (Paul Edgington, 2015-09-30)<br />
* Mark Calleta (Paul Edgington, 2015-09-30)<br />
* Martin Lenz (Paul Edgington, 2015-09-30)<br />
* Phill Banks (Paul Edgington, 2015-10-21)<br />
* Felix Morley (Paul Edgington, 2015-10-21)<br />
* David Jordan (Paul Edgington, 2015-10-21)<br />
* Mark Roberts (Stephen Harrison, 2015-10-23)<br />
* Jenny Molloy (Stephen Harrison, 2015-10-23)<br />
* Henry Cawley (Rob Voisey, 2015-11-18)<br />
* Bogdan Spiridom (Rob Voisey, 2015-11-18)<br />
* Jakub Sanak (Rob Voisey, 2015-11-18)<br />
* Jack Brewster (Rob Voisey, 2015-11-18)<br />
* Mayke Santos (Rob Voisey, 2015-11-18)<br />
* Luis Veiga Pumar (Stephen Harrison, 2015-11-24)<br />
* Greg Matthews (Stephen Harrison, 2015-11-24)<br />
* Brian Corteil (Stephen Harrison, 2015-11-24)<br />
* Rob Rescorla (Stephen Harrison, 2015-11-24)<br />
* Leo Rones (Stephen Harrison, 2015-11-24)<br />
* Diana Probst (Stephen Harrison, 2015-11-25)<br />
* Adrian van den Heever (Stephen Harrison, 2015-11-25)<br />
* Al Napp (Stephen Harrison, 2015-11-25)<br />
* Katy Marshall (Stephen Harrison, 2015-12-01)<br />
* Peter Mottram (Stephen Harrison, 2015-12-01)<br />
* David Barham (Stephen Harrison, 2015-12-01)<br />
* Johan Henriksson (Stephen Harrison, 2015-12-01)<br />
* Fotis Fotiadis (Stephen Harrison, 2015-12-01)<br />
* Oliver Martin (Stephen Harrison, 2015-12-01)<br />
* Andrew Drummond (Stephen Harrison, 2015-12-01)<br />
* Spencer Dixon (Stephen Harrison, 2015-12-01)<br />
* Jonathan Woolf (Rob Voisey, 2016-01-07)<br />
* Daniel Bailey (Rob Voisey, 2016-01-07)<br />
* David Haines (Rob Voisey, 2016-01-07)<br />
* Giovanni Bisutii (Rob Voisey, 2016-01-07)<br />
* Simon Hartley (Daniel Bailey, 2016-02-11)<br />
* Francois Eve (Daniel Bailey, 2016-02-11)<br />
* Giovanni Orlando (Daniel Bailey, 2016-02-11)<br />
* Dan Tidhar (Daniel Bailey, 2016-02-11)<br />
* Shunsuke Fujibayashi (Daniel Bailey, 2016-03-04)<br />
* Ronny Schlutter (Daniel Bailey, 2016-03-04)<br />
* Jamie Powell (Daniel Bailey, 2016-03-04)<br />
* Mark Wainwright (Daniel Bailey, 2016-03-04)<br />
* Charna Hume (Daniel Bailey, 2016-03-04)<br />
* Charlotte Godley (Daniel Bailey, 2016-03-04)<br />
* Jose Chitty (Stephen Harrison, 2016-03-22)<br />
* Mat Greenwood (Stephen Harrison, 2016-03-22)<br />
* David Fisher (Stephen Harrison, 2016-03-22)<br />
* Tom Kelly (Stephen Harrison, 2016-03-22)<br />
* David Bebb (Stephen Harrison, 2016-04-12)<br />
* David Taylor (Stephen Harrison, 2016-04-12)<br />
* Jo Brook (Stephen Harrison, 2016-04-12)<br />
* Craig Easton (Daniel Bailey, 2016-04-20)<br />
* James Griffiths (Daniel Bailey, 2016-04-20)<br />
* Paul Routley (Daniel Bailey, 2016-04-20)<br />
* Steve Murphy (Daniel Bailey, 2016-04-20)</div>Danieljabaileyhttp://wiki.makespace.org/Equipment/3D_Printer/UM2TrainingEquipment/3D Printer/UM2Training2016-04-20T19:55:45Z<p>Danieljabailey: /* Trained Users */ Added users trained 2016-04-20</p>
<hr />
<div>[[Equipment|Equipment]] / [[Equipment/3D Printer|UM2]] / Training<br />
<br />
= Ultimaker 2 3D Printer Training =<br />
<br />
This page documents the process for being trained on the Ultimaker 2 Printer, and the list of members who have completed that training.<br />
<br />
== Summary ==<br />
<br />
Training takes place in three main steps:<br />
* Group Training of 1-4 members, going through the equipment and how to use it (~1hr)<br />
* Individual Training Task, where an individual member is set a task to complete to prove and improve understanding (~20min each)<br />
* Recommended project oversight, where more experienced users oversee the projects being undertaken when cutting (first 2-3 projects)<br />
<br />
A shorter conversion training session is available for members who were previously signed off to use the Makerbot 2X printer. These sessions last around 20 minutes and do not include individual sessions.<br />
<br />
== Booking ==<br />
<br />
For discussing and arranging slots, please use the mailing list. New training sessions will be announced on the Meetup group.<br />
<br />
Notes:<br />
* You can only be trained if you have RSVP'd to a Meetup session<br />
<br />
== Training Cheatsheet - Conversion Course ==<br />
<br />
Members already trained on and familiar with the Makerbot 2X can attend this short conversion course to be signed off to use the Ultimaker 2 3D printer. Up to 10 people can be accommodated on each course, which lasts 20 to 30 minutes.<br />
<br />
1. Physical Differences from the 2X<br />
* Glass build plate, no kapton tape<br />
* Single extruder<br />
* Push feed<br />
<br />
2. General<br />
* Use the correct filament (2.85mm, NOT 3mm or 1.75mm)<br />
* New filament storage system<br />
<br />
3. Printing<br />
* Fence / Brim / Raft<br />
* OK to leave printer unattended after the first few layers<br />
* Camera available for remote monitoring<br />
* Use only plastic implements for part removal, take care not to melt them on the hot end<br />
<br />
4. Cura Software<br />
* Import and place<br />
* Simple mode<br />
* Brief overview of advanced mode<br />
* Temperature set on printer not slicer<br />
* Exporting to SD card<br />
<br />
5. Unload / Load filament<br />
* How to feed (slow first, then fast)<br />
* Select correct material in menu<br />
* Changing temperature and speed parameters from printer<br />
* Demonstrate the atomic method of cleaning the extruder to prevent feed jams<br />
<br />
6. Filament pricing<br />
* 5p per gram for PLA and ABS, to be kept under review<br />
* Include wastage!<br />
<br />
== Training Cheatsheet - Full Course ==<br />
<br />
'''Group Session'''<br />
<br />
1. Ask what each member hopes to get out of the 3D printer.<br />
<br />
2. Explain how 3D printing works<br />
<br />
3. Safety<br />
* Burn hazard – nozzle and build plate<br />
* Unit may move unexpectedly<br />
* Avoid prolonged exposure to ABS fumes<br />
<br />
4. Damage to machine<br />
* Fragile build plate<br />
* Jammed filament<br />
<br />
5. General<br />
* Use the correct filament (2.85mm)<br />
* Filament storage and feed system<br />
* Switch off when finished<br />
* Leave levelling to the owners but report any problems<br />
<br />
6. PLA vs ABS<br />
* How to tell the difference<br />
* Different temperature<br />
* PLA Biodegradable<br />
<br />
7. Software / workflow<br />
* Importing<br />
* Positioning on bed<br />
* Supports<br />
* Setting quality / speed trade off<br />
* Advanced options<br />
* Exporting to SD card<br />
<br />
8. Unload / load<br />
* Attaching spool or loading from storage box<br />
* Feeding (slow then fast)<br />
* Beware of wrapping round axle<br />
* Setting material in menu<br />
* Adjusting parameters, e.g. ABS plate temperature<br />
<br />
9. Printing<br />
* Preheating<br />
* Fence printing<br />
* Keep an eye on progress, locally or with camera<br />
* If leaving unattended, put a post-it with your contact details<br />
* Use only plastic implements for part removal<br />
<br />
10. Other stuff<br />
* Demonstrate atomic method of cleaning the nozzle to prevent feed jams<br />
* Strength characteristics – orientation is important<br />
* Paying<br />
<br />
'''Individual Training Task'''<br />
<br />
Task<br />
* Should demonstrate import, setup, position and run<br />
* Choose a part that takes about 10 mins to print (preloaded on PC)<br />
<br />
Steps<br />
* Set individual to work, don't prompt but do answer questions (or pose if needed)<br />
* Talk through design once done, question/check things etc<br />
* Proceed to printing (watch carefully all steps)<br />
<br />
Assuming all ok:<br />
* Get them to read the health and safety notes about operation and materials<br />
* Add to the trained member list<br />
<br />
'''Project Oversight'''<br />
<br />
For next 2-3 projects, recommend member will find another more experienced trained user to support them (second pair of eyes)<br />
<br />
This cheat-sheet is available in PDF form on a single side of A4 [http://wiki.makespace.org/File:TrainingCheatsheetUM2.pdf here].<br />
<br />
== Trained Users ==<br />
<br />
The following members of Makespace are trained and qualified to use the 3D Printer (note, they are not qualified to train others however):<br />
<br />
* Paul Osborn (Rob Voisey, 2015-07-30)<br />
* Julius Schmidt (Rob Voisey, 2015-07-30)<br />
* Peter Knight (Rob Voisey, 2015-07-30)<br />
* Adam Mulligan (Rob Voisey, 2015-07-30)<br />
* Charlotte Harvey (Rob Voisey, 2015-07-30)<br />
* Alex Gee (Rob Voisey, 2015-07-30)<br />
* Albert Santos (Rob Voisey, 2015-07-30)<br />
* Zizwani Mhango (Rob Voisey, 2015-07-30)<br />
* Christie Nel (Rob Voisey, 2015-07-30)<br />
* Robert Karpinski (Rob Voisey, 2015-07-30)<br />
* Alexis Mather (Stephen Harrison, 2015-08-03)<br />
* Ben Wheatley (Stephen Harrison, 2015-08-03)<br />
* Stevan Wing (Stephen Harrison, 2015-08-03)<br />
* Jae Tumer (Stephen Harrison, 2015-08-03)<br />
* Jennifer Herbert (Stephen Harrison, 2015-08-03)<br />
* Frodi Jones (Stephen Harrison, 2015-08-03)<br />
* Matt Wayland (Stephen Harrison, 2015-08-03)<br />
* Marco Aite (Stephen Harrison, 2015-08-03)<br />
* Graeham Douglas (Stephen Harrison, 2015-08-03)<br />
* Robin Sterling (Stephen Harrison, 2015-08-07)<br />
* Abhi Manyu (Stephen Harrison, 2015-08-07)<br />
* Ward Hills (Stephen Harrison, 2015-08-07)<br />
* Carols A. Lugo (Stephen Harrison, 2015-08-07)<br />
* Ben Alper (Stephen Harrison, 2015-08-07)<br />
* Jon Green (Stephen Harrison, 2015-08-07)<br />
* Marcin Izo (Stephen Harrison, 2015-08-07)<br />
* Steve Upton (Rob Voisey, 2015-08-11)<br />
* Frederic Sorgeloos (Rob Voisey, 2015-08-11)<br />
* Andrew Cooke (Rob Voisey, 2015-08-11)<br />
* Ned Booker (Rob Voisey, 2015-08-11)<br />
* Daryl Stewart (Paul Edgington, 2015-08-24)<br />
* Nacho Lopez (Paul Edgington, 2015-08-24)<br />
* Ed Robertson (Paul Edgington, 2015-08-24)<br />
* Clive Beale (Paul Edgington, 2015-08-24)<br />
* Oliver Fleck (Paul Edgington, 2015-08-24)<br />
* Mark Cheverton (Rob Voisey, 2015-09-08)<br />
* Nik (Rob Voisey, 2015-09-08)<br />
* Dan Tidhar (Rob Voisey, 2015-09-08)<br />
* Tobias Wenzel (Rob Voisey, 2015-09-08)<br />
* Brian Starkey (Rob Voisey, 2015-09-08)<br />
* Jonathan Waite (Rob Voisey, 2015-09-08)<br />
* Emyr James (Rob Voisey, 2015-09-08)<br />
* Richard Hall (Rob Voisey, 2015-09-08)<br />
* Andrew Dunn (Rob Voisey, 2015-09-08)<br />
* Andrea Cipri (Paul Edgington, 2015-09-30)<br />
* John Sidinopoulos (Paul Edgington, 2015-09-30)<br />
* Stuart Barton (Paul Edgington, 2015-09-30)<br />
* Mark Calleta (Paul Edgington, 2015-09-30)<br />
* Martin Lenz (Paul Edgington, 2015-09-30)<br />
* Phill Banks (Paul Edgington, 2015-10-21)<br />
* Felix Morley (Paul Edgington, 2015-10-21)<br />
* David Jordan (Paul Edgington, 2015-10-21)<br />
* Mark Roberts (Stephen Harrison, 2015-10-23)<br />
* Jenny Molloy (Stephen Harrison, 2015-10-23)<br />
* Henry Cawley (Rob Voisey, 2015-11-18)<br />
* Bogdan Spiridom (Rob Voisey, 2015-11-18)<br />
* Jakub Sanak (Rob Voisey, 2015-11-18)<br />
* Jack Brewster (Rob Voisey, 2015-11-18)<br />
* Mayke Santos (Rob Voisey, 2015-11-18)<br />
* Luis Veiga Pumar (Stephen Harrison, 2015-11-24)<br />
* Greg Matthews (Stephen Harrison, 2015-11-24)<br />
* Brian Corteil (Stephen Harrison, 2015-11-24)<br />
* Rob Rescorla (Stephen Harrison, 2015-11-24)<br />
* Leo Rones (Stephen Harrison, 2015-11-24)<br />
* Diana Probst (Stephen Harrison, 2015-11-25)<br />
* Adrian van den Heever (Stephen Harrison, 2015-11-25)<br />
* Al Napp (Stephen Harrison, 2015-11-25)<br />
* Katy Marshall (Stephen Harrison, 2015-12-01)<br />
* Peter Mottram (Stephen Harrison, 2015-12-01)<br />
* David Barham (Stephen Harrison, 2015-12-01)<br />
* Johan Henriksson (Stephen Harrison, 2015-12-01)<br />
* Fotis Fotiadis (Stephen Harrison, 2015-12-01)<br />
* Oliver Martin (Stephen Harrison, 2015-12-01)<br />
* Andrew Drummond (Stephen Harrison, 2015-12-01)<br />
* Spencer Dixon (Stephen Harrison, 2015-12-01)<br />
* Jonathan Woolf (Rob Voisey, 2016-01-07)<br />
* Daniel Bailey (Rob Voisey, 2016-01-07)<br />
* David Haines (Rob Voisey, 2016-01-07)<br />
* Giovanni Bisutii (Rob Voisey, 2016-01-07)<br />
* Simon Hartley (Daniel Bailey, 2016-02-11)<br />
* Francois Eve (Daniel Bailey, 2016-02-11)<br />
* Giovanni Orlando (Daniel Bailey, 2016-02-11)<br />
* Dan Tidhar (Daniel Bailey, 2016-02-11)<br />
* Shunsuke Fujibayashi (Daniel Bailey, 2016-03-04)<br />
* Ronny Schlutter (Daniel Bailey, 2016-03-04)<br />
* Jamie Powell (Daniel Bailey, 2016-03-04)<br />
* Mark Wainwright (Daniel Bailey, 2016-03-04)<br />
* Charna Hume (Daniel Bailey, 2016-03-04)<br />
* Charlotte Godley (Daniel Bailey, 2016-03-04)<br />
* Jose Chitty (Stephen Harrison, 2016-03-22)<br />
* Mat Greenwood (Stephen Harrison, 2016-03-22)<br />
* David Fisher (Stephen Harrison, 2016-03-22)<br />
* Tom Kelly (Stephen Harrison, 2016-03-22)<br />
* David Bebb (Stephen Harrison, 2016-04-12)<br />
* David Taylor (Stephen Harrison, 2016-04-12)<br />
* Jo Brook (Stephen Harrison, 2016-04-12)<br />
* Craig Easton (Daniel Bailey, 2016-04-20)<br />
* James Griffiths (Daniel Bailey, 2016-04-20)<br />
* Paul Routley (Daniel Bailey, 2016-04-20)<br />
* Steve M (Daniel Bailey, 2016-04-20)</div>Danieljabaileyhttp://wiki.makespace.org/Equipment/3D_Printer/UM2TrainingEquipment/3D Printer/UM2Training2016-03-04T21:49:03Z<p>Danieljabailey: /* Trained Users */ Oops, missed mark. How could I do such a thing. :-)</p>
<hr />
<div>[[Equipment|Equipment]] / [[Equipment/3D Printer|UM2]] / Training<br />
<br />
= Ultimaker 2 3D Printer Training =<br />
<br />
This page documents the process for being trained on the Ultimaker 2 Printer, and the list of members who have completed that training.<br />
<br />
== Summary ==<br />
<br />
Training takes place in three main steps:<br />
* Group Training of 1-4 members, going through the equipment and how to use it (~1hr)<br />
* Individual Training Task, where an individual member is set a task to complete to prove and improve understanding (~20min each)<br />
* Recommended project oversight, where more experienced users oversee the projects being undertaken when cutting (first 2-3 projects)<br />
<br />
A shorter conversion training session is available for members who were previously signed off to use the Makerbot 2X printer. These sessions last around 20 minutes and do not include individual sessions.<br />
<br />
== Booking ==<br />
<br />
For discussing and arranging slots, please use the mailing list. New training sessions will be announced on the Meetup group.<br />
<br />
Notes:<br />
* You can only be trained if you have RSVP'd to a Meetup session<br />
<br />
== Training Cheatsheet - Conversion Course ==<br />
<br />
Members already trained on and familiar with the Makerbot 2X can attend this short conversion course to be signed off to use the Ultimaker 2 3D printer. Up to 10 people can be accommodated on each course, which lasts 20 to 30 minutes.<br />
<br />
1. Physical Differences from the 2X<br />
* Glass build plate, no kapton tape<br />
* Single extruder<br />
* Push feed<br />
<br />
2. General<br />
* Use the correct filament (2.85mm, NOT 3mm or 1.75mm)<br />
* New filament storage system<br />
<br />
3. Printing<br />
* Fence / Brim / Raft<br />
* OK to leave printer unattended after the first few layers<br />
* Camera available for remote monitoring<br />
* Use only plastic implements for part removal, take care not to melt them on the hot end<br />
<br />
4. Cura Software<br />
* Import and place<br />
* Simple mode<br />
* Brief overview of advanced mode<br />
* Temperature set on printer not slicer<br />
* Exporting to SD card<br />
<br />
5. Unload / Load filament<br />
* How to feed (slow first, then fast)<br />
* Select correct material in menu<br />
* Changing temperature and speed parameters from printer<br />
* Demonstrate the atomic method of cleaning the extruder to prevent feed jams<br />
<br />
6. Filament pricing<br />
* 5p per gram for PLA and ABS, to be kept under review<br />
* Include wastage!<br />
<br />
== Training Cheatsheet - Full Course ==<br />
<br />
'''Group Session'''<br />
<br />
1. Ask what each member hopes to get out of the 3D printer.<br />
<br />
2. Explain how 3D printing works<br />
<br />
3. Safety<br />
* Burn hazard – nozzle and build plate<br />
* Unit may move unexpectedly<br />
* Avoid prolonged exposure to ABS fumes<br />
<br />
4. Damage to machine<br />
* Fragile build plate<br />
* Jammed filament<br />
<br />
5. General<br />
* Use the correct filament (2.85mm)<br />
* Filament storage and feed system<br />
* Switch off when finished<br />
* Leave levelling to the owners but report any problems<br />
<br />
6. PLA vs ABS<br />
* How to tell the difference<br />
* Different temperature<br />
* PLA Biodegradable<br />
<br />
7. Software / workflow<br />
* Importing<br />
* Positioning on bed<br />
* Supports<br />
* Setting quality / speed trade off<br />
* Advanced options<br />
* Exporting to SD card<br />
<br />
8. Unload / load<br />
* Attaching spool or loading from storage box<br />
* Feeding (slow then fast)<br />
* Beware of wrapping round axle<br />
* Setting material in menu<br />
* Adjusting parameters, e.g. ABS plate temperature<br />
<br />
9. Printing<br />
* Preheating<br />
* Fence printing<br />
* Keep an eye on progress, locally or with camera<br />
* If leaving unattended, put a post-it with your contact details<br />
* Use only plastic implements for part removal<br />
<br />
10. Other stuff<br />
* Demonstrate atomic method of cleaning the nozzle to prevent feed jams<br />
* Strength characteristics – orientation is important<br />
* Paying<br />
<br />
'''Individual Training Task'''<br />
<br />
Task<br />
* Should demonstrate import, setup, position and run<br />
* Choose a part that takes about 10 mins to print (preloaded on PC)<br />
<br />
Steps<br />
* Set individual to work, don't prompt but do answer questions (or pose if needed)<br />
* Talk through design once done, question/check things etc<br />
* Proceed to printing (watch carefully all steps)<br />
<br />
Assuming all ok:<br />
* Get them to read the health and safety notes about operation and materials<br />
* Add to the trained member list<br />
<br />
'''Project Oversight'''<br />
<br />
For next 2-3 projects, recommend member will find another more experienced trained user to support them (second pair of eyes)<br />
<br />
This cheat-sheet is available in PDF form on a single side of A4 [http://wiki.makespace.org/File:TrainingCheatsheetUM2.pdf here].<br />
<br />
== Trained Users ==<br />
<br />
The following members of Makespace are trained and qualified to use the 3D Printer (note, they are not qualified to train others however):<br />
<br />
* Paul Osborn (Rob Voisey, 2015-07-30)<br />
* Julius Schmidt (Rob Voisey, 2015-07-30)<br />
* Peter Knight (Rob Voisey, 2015-07-30)<br />
* Adam Mulligan (Rob Voisey, 2015-07-30)<br />
* Charlotte Harvey (Rob Voisey, 2015-07-30)<br />
* Alex Gee (Rob Voisey, 2015-07-30)<br />
* Albert Santos (Rob Voisey, 2015-07-30)<br />
* Zizwani Mhango (Rob Voisey, 2015-07-30)<br />
* Christie Nel (Rob Voisey, 2015-07-30)<br />
* Robert Karpinski (Rob Voisey, 2015-07-30)<br />
* Alexis Mather (Stephen Harrison, 2015-08-03)<br />
* Ben Wheatley (Stephen Harrison, 2015-08-03)<br />
* Stevan Wing (Stephen Harrison, 2015-08-03)<br />
* Jae Tumer (Stephen Harrison, 2015-08-03)<br />
* Jennifer Herbert (Stephen Harrison, 2015-08-03)<br />
* Frodi Jones (Stephen Harrison, 2015-08-03)<br />
* Matt Wayland (Stephen Harrison, 2015-08-03)<br />
* Marco Aite (Stephen Harrison, 2015-08-03)<br />
* Graeham Douglas (Stephen Harrison, 2015-08-03)<br />
* Robin Sterling (Stephen Harrison, 2015-08-07)<br />
* Abhi Manyu (Stephen Harrison, 2015-08-07)<br />
* Ward Hills (Stephen Harrison, 2015-08-07)<br />
* Carols A. Lugo (Stephen Harrison, 2015-08-07)<br />
* Ben Alper (Stephen Harrison, 2015-08-07)<br />
* Jon Green (Stephen Harrison, 2015-08-07)<br />
* Marcin Izo (Stephen Harrison, 2015-08-07)<br />
* Steve Upton (Rob Voisey, 2015-08-11)<br />
* Frederic Sorgeloos (Rob Voisey, 2015-08-11)<br />
* Andrew Cooke (Rob Voisey, 2015-08-11)<br />
* Ned Booker (Rob Voisey, 2015-08-11)<br />
* Daryl Stewart (Paul Edgington, 2015-08-24)<br />
* Nacho Lopez (Paul Edgington, 2015-08-24)<br />
* Ed Robertson (Paul Edgington, 2015-08-24)<br />
* Clive Beale (Paul Edgington, 2015-08-24)<br />
* Oliver Fleck (Paul Edgington, 2015-08-24)<br />
* Mark Cheverton (Rob Voisey, 2015-09-08)<br />
* Nik (Rob Voisey, 2015-09-08)<br />
* Dan Tidhar (Rob Voisey, 2015-09-08)<br />
* Tobias Wenzel (Rob Voisey, 2015-09-08)<br />
* Brian Starkey (Rob Voisey, 2015-09-08)<br />
* Jonathan Waite (Rob Voisey, 2015-09-08)<br />
* Emyr James (Rob Voisey, 2015-09-08)<br />
* Richard Hall (Rob Voisey, 2015-09-08)<br />
* Andrew Dunn (Rob Voisey, 2015-09-08)<br />
* Andrea Cipri (Paul Edgington, 2015-09-30)<br />
* John Sidinopoulos (Paul Edgington, 2015-09-30)<br />
* Stuart Barton (Paul Edgington, 2015-09-30)<br />
* Mark Calleta (Paul Edgington, 2015-09-30)<br />
* Martin Lenz (Paul Edgington, 2015-09-30)<br />
* Phill Banks (Paul Edgington, 2015-10-21)<br />
* Felix Morley (Paul Edgington, 2015-10-21)<br />
* David Jordan (Paul Edgington, 2015-10-21)<br />
* Mark Roberts (Stephen Harrison, 2015-10-23)<br />
* Jenny Molloy (Stephen Harrison, 2015-10-23)<br />
* Henry Cawley (Rob Voisey, 2015-11-18)<br />
* Bogdan Spiridom (Rob Voisey, 2015-11-18)<br />
* Jakub Sanak (Rob Voisey, 2015-11-18)<br />
* Jack Brewster (Rob Voisey, 2015-11-18)<br />
* Mayke Santos (Rob Voisey, 2015-11-18)<br />
* Luis Veiga Pumar (Stephen Harrison, 2015-11-24)<br />
* Greg Matthews (Stephen Harrison, 2015-11-24)<br />
* Brian Corteil (Stephen Harrison, 2015-11-24)<br />
* Rob Rescorla (Stephen Harrison, 2015-11-24)<br />
* Leo Rones (Stephen Harrison, 2015-11-24)<br />
* Diana Probst (Stephen Harrison, 2015-11-25)<br />
* Adrian van den Heever (Stephen Harrison, 2015-11-25)<br />
* Al Napp (Stephen Harrison, 2015-11-25)<br />
* Katy Marshall (Stephen Harrison, 2015-12-01)<br />
* Peter Mottram (Stephen Harrison, 2015-12-01)<br />
* David Barham (Stephen Harrison, 2015-12-01)<br />
* Johan Henriksson (Stephen Harrison, 2015-12-01)<br />
* Fotis Fotiadis (Stephen Harrison, 2015-12-01)<br />
* Oliver Martin (Stephen Harrison, 2015-12-01)<br />
* Andrew Drummond (Stephen Harrison, 2015-12-01)<br />
* Spencer Dixon (Stephen Harrison, 2015-12-01)<br />
* Jonathan Woolf (Rob Voisey, 2016-01-07)<br />
* Daniel Bailey (Rob Voisey, 2016-01-07)<br />
* David Haines (Rob Voisey, 2016-01-07)<br />
* Giovanni Bisutii (Rob Voisey, 2016-01-07)<br />
* Simon Hartley (Daniel Bailey, 2016-02-11)<br />
* Francois Eve (Daniel Bailey, 2016-02-11)<br />
* Giovanni Orlando (Daniel Bailey, 2016-02-11)<br />
* Dan Tidhar (Daniel Bailey, 2016-02-11)<br />
* Shunsuke Fujibayashi (Daniel Bailey, 2016-03-04)<br />
* Ronny Schlutter (Daniel Bailey, 2016-03-04)<br />
* Jamie Powell (Daniel Bailey, 2016-03-04)<br />
* Mark Wainwright (Daniel Bailey, 2016-03-04)<br />
* Charna Hume (Daniel Bailey, 2016-03-04)<br />
* Charlotte Godley (Daniel Bailey, 2016-03-04)</div>Danieljabaileyhttp://wiki.makespace.org/Equipment/3D_Printer/UM2TrainingEquipment/3D Printer/UM2Training2016-03-04T21:48:07Z<p>Danieljabailey: /* Trained Users */ Added users trained on 2016-03-04</p>
<hr />
<div>[[Equipment|Equipment]] / [[Equipment/3D Printer|UM2]] / Training<br />
<br />
= Ultimaker 2 3D Printer Training =<br />
<br />
This page documents the process for being trained on the Ultimaker 2 Printer, and the list of members who have completed that training.<br />
<br />
== Summary ==<br />
<br />
Training takes place in three main steps:<br />
* Group Training of 1-4 members, going through the equipment and how to use it (~1hr)<br />
* Individual Training Task, where an individual member is set a task to complete to prove and improve understanding (~20min each)<br />
* Recommended project oversight, where more experienced users oversee the projects being undertaken when cutting (first 2-3 projects)<br />
<br />
A shorter conversion training session is available for members who were previously signed off to use the Makerbot 2X printer. These sessions last around 20 minutes and do not include individual sessions.<br />
<br />
== Booking ==<br />
<br />
For discussing and arranging slots, please use the mailing list. New training sessions will be announced on the Meetup group.<br />
<br />
Notes:<br />
* You can only be trained if you have RSVP'd to a Meetup session<br />
<br />
== Training Cheatsheet - Conversion Course ==<br />
<br />
Members already trained on and familiar with the Makerbot 2X can attend this short conversion course to be signed off to use the Ultimaker 2 3D printer. Up to 10 people can be accommodated on each course, which lasts 20 to 30 minutes.<br />
<br />
1. Physical Differences from the 2X<br />
* Glass build plate, no kapton tape<br />
* Single extruder<br />
* Push feed<br />
<br />
2. General<br />
* Use the correct filament (2.85mm, NOT 3mm or 1.75mm)<br />
* New filament storage system<br />
<br />
3. Printing<br />
* Fence / Brim / Raft<br />
* OK to leave printer unattended after the first few layers<br />
* Camera available for remote monitoring<br />
* Use only plastic implements for part removal, take care not to melt them on the hot end<br />
<br />
4. Cura Software<br />
* Import and place<br />
* Simple mode<br />
* Brief overview of advanced mode<br />
* Temperature set on printer not slicer<br />
* Exporting to SD card<br />
<br />
5. Unload / Load filament<br />
* How to feed (slow first, then fast)<br />
* Select correct material in menu<br />
* Changing temperature and speed parameters from printer<br />
* Demonstrate the atomic method of cleaning the extruder to prevent feed jams<br />
<br />
6. Filament pricing<br />
* 5p per gram for PLA and ABS, to be kept under review<br />
* Include wastage!<br />
<br />
== Training Cheatsheet - Full Course ==<br />
<br />
'''Group Session'''<br />
<br />
1. Ask what each member hopes to get out of the 3D printer.<br />
<br />
2. Explain how 3D printing works<br />
<br />
3. Safety<br />
* Burn hazard – nozzle and build plate<br />
* Unit may move unexpectedly<br />
* Avoid prolonged exposure to ABS fumes<br />
<br />
4. Damage to machine<br />
* Fragile build plate<br />
* Jammed filament<br />
<br />
5. General<br />
* Use the correct filament (2.85mm)<br />
* Filament storage and feed system<br />
* Switch off when finished<br />
* Leave levelling to the owners but report any problems<br />
<br />
6. PLA vs ABS<br />
* How to tell the difference<br />
* Different temperature<br />
* PLA Biodegradable<br />
<br />
7. Software / workflow<br />
* Importing<br />
* Positioning on bed<br />
* Supports<br />
* Setting quality / speed trade off<br />
* Advanced options<br />
* Exporting to SD card<br />
<br />
8. Unload / load<br />
* Attaching spool or loading from storage box<br />
* Feeding (slow then fast)<br />
* Beware of wrapping round axle<br />
* Setting material in menu<br />
* Adjusting parameters, e.g. ABS plate temperature<br />
<br />
9. Printing<br />
* Preheating<br />
* Fence printing<br />
* Keep an eye on progress, locally or with camera<br />
* If leaving unattended, put a post-it with your contact details<br />
* Use only plastic implements for part removal<br />
<br />
10. Other stuff<br />
* Demonstrate atomic method of cleaning the nozzle to prevent feed jams<br />
* Strength characteristics – orientation is important<br />
* Paying<br />
<br />
'''Individual Training Task'''<br />
<br />
Task<br />
* Should demonstrate import, setup, position and run<br />
* Choose a part that takes about 10 mins to print (preloaded on PC)<br />
<br />
Steps<br />
* Set individual to work, don't prompt but do answer questions (or pose if needed)<br />
* Talk through design once done, question/check things etc<br />
* Proceed to printing (watch carefully all steps)<br />
<br />
Assuming all ok:<br />
* Get them to read the health and safety notes about operation and materials<br />
* Add to the trained member list<br />
<br />
'''Project Oversight'''<br />
<br />
For next 2-3 projects, recommend member will find another more experienced trained user to support them (second pair of eyes)<br />
<br />
This cheat-sheet is available in PDF form on a single side of A4 [http://wiki.makespace.org/File:TrainingCheatsheetUM2.pdf here].<br />
<br />
== Trained Users ==<br />
<br />
The following members of Makespace are trained and qualified to use the 3D Printer (note, they are not qualified to train others however):<br />
<br />
* Paul Osborn (Rob Voisey, 2015-07-30)<br />
* Julius Schmidt (Rob Voisey, 2015-07-30)<br />
* Peter Knight (Rob Voisey, 2015-07-30)<br />
* Adam Mulligan (Rob Voisey, 2015-07-30)<br />
* Charlotte Harvey (Rob Voisey, 2015-07-30)<br />
* Alex Gee (Rob Voisey, 2015-07-30)<br />
* Albert Santos (Rob Voisey, 2015-07-30)<br />
* Zizwani Mhango (Rob Voisey, 2015-07-30)<br />
* Christie Nel (Rob Voisey, 2015-07-30)<br />
* Robert Karpinski (Rob Voisey, 2015-07-30)<br />
* Alexis Mather (Stephen Harrison, 2015-08-03)<br />
* Ben Wheatley (Stephen Harrison, 2015-08-03)<br />
* Stevan Wing (Stephen Harrison, 2015-08-03)<br />
* Jae Tumer (Stephen Harrison, 2015-08-03)<br />
* Jennifer Herbert (Stephen Harrison, 2015-08-03)<br />
* Frodi Jones (Stephen Harrison, 2015-08-03)<br />
* Matt Wayland (Stephen Harrison, 2015-08-03)<br />
* Marco Aite (Stephen Harrison, 2015-08-03)<br />
* Graeham Douglas (Stephen Harrison, 2015-08-03)<br />
* Robin Sterling (Stephen Harrison, 2015-08-07)<br />
* Abhi Manyu (Stephen Harrison, 2015-08-07)<br />
* Ward Hills (Stephen Harrison, 2015-08-07)<br />
* Carols A. Lugo (Stephen Harrison, 2015-08-07)<br />
* Ben Alper (Stephen Harrison, 2015-08-07)<br />
* Jon Green (Stephen Harrison, 2015-08-07)<br />
* Marcin Izo (Stephen Harrison, 2015-08-07)<br />
* Steve Upton (Rob Voisey, 2015-08-11)<br />
* Frederic Sorgeloos (Rob Voisey, 2015-08-11)<br />
* Andrew Cooke (Rob Voisey, 2015-08-11)<br />
* Ned Booker (Rob Voisey, 2015-08-11)<br />
* Daryl Stewart (Paul Edgington, 2015-08-24)<br />
* Nacho Lopez (Paul Edgington, 2015-08-24)<br />
* Ed Robertson (Paul Edgington, 2015-08-24)<br />
* Clive Beale (Paul Edgington, 2015-08-24)<br />
* Oliver Fleck (Paul Edgington, 2015-08-24)<br />
* Mark Cheverton (Rob Voisey, 2015-09-08)<br />
* Nik (Rob Voisey, 2015-09-08)<br />
* Dan Tidhar (Rob Voisey, 2015-09-08)<br />
* Tobias Wenzel (Rob Voisey, 2015-09-08)<br />
* Brian Starkey (Rob Voisey, 2015-09-08)<br />
* Jonathan Waite (Rob Voisey, 2015-09-08)<br />
* Emyr James (Rob Voisey, 2015-09-08)<br />
* Richard Hall (Rob Voisey, 2015-09-08)<br />
* Andrew Dunn (Rob Voisey, 2015-09-08)<br />
* Andrea Cipri (Paul Edgington, 2015-09-30)<br />
* John Sidinopoulos (Paul Edgington, 2015-09-30)<br />
* Stuart Barton (Paul Edgington, 2015-09-30)<br />
* Mark Calleta (Paul Edgington, 2015-09-30)<br />
* Martin Lenz (Paul Edgington, 2015-09-30)<br />
* Phill Banks (Paul Edgington, 2015-10-21)<br />
* Felix Morley (Paul Edgington, 2015-10-21)<br />
* David Jordan (Paul Edgington, 2015-10-21)<br />
* Mark Roberts (Stephen Harrison, 2015-10-23)<br />
* Jenny Molloy (Stephen Harrison, 2015-10-23)<br />
* Henry Cawley (Rob Voisey, 2015-11-18)<br />
* Bogdan Spiridom (Rob Voisey, 2015-11-18)<br />
* Jakub Sanak (Rob Voisey, 2015-11-18)<br />
* Jack Brewster (Rob Voisey, 2015-11-18)<br />
* Mayke Santos (Rob Voisey, 2015-11-18)<br />
* Luis Veiga Pumar (Stephen Harrison, 2015-11-24)<br />
* Greg Matthews (Stephen Harrison, 2015-11-24)<br />
* Brian Corteil (Stephen Harrison, 2015-11-24)<br />
* Rob Rescorla (Stephen Harrison, 2015-11-24)<br />
* Leo Rones (Stephen Harrison, 2015-11-24)<br />
* Diana Probst (Stephen Harrison, 2015-11-25)<br />
* Adrian van den Heever (Stephen Harrison, 2015-11-25)<br />
* Al Napp (Stephen Harrison, 2015-11-25)<br />
* Katy Marshall (Stephen Harrison, 2015-12-01)<br />
* Peter Mottram (Stephen Harrison, 2015-12-01)<br />
* David Barham (Stephen Harrison, 2015-12-01)<br />
* Johan Henriksson (Stephen Harrison, 2015-12-01)<br />
* Fotis Fotiadis (Stephen Harrison, 2015-12-01)<br />
* Oliver Martin (Stephen Harrison, 2015-12-01)<br />
* Andrew Drummond (Stephen Harrison, 2015-12-01)<br />
* Spencer Dixon (Stephen Harrison, 2015-12-01)<br />
* Jonathan Woolf (Rob Voisey, 2016-01-07)<br />
* Daniel Bailey (Rob Voisey, 2016-01-07)<br />
* David Haines (Rob Voisey, 2016-01-07)<br />
* Giovanni Bisutii (Rob Voisey, 2016-01-07)<br />
* Simon Hartley (Daniel Bailey, 2016-02-11)<br />
* Francois Eve (Daniel Bailey, 2016-02-11)<br />
* Giovanni Orlando (Daniel Bailey, 2016-02-11)<br />
* Dan Tidhar (Daniel Bailey, 2016-02-11)<br />
* Shunsuke Fujibayashi (Daniel Bailey, 2016-03-04)<br />
* Ronny Schlutter (Daniel Bailey, 2016-03-04)<br />
* Jamie Powell (Daniel Bailey, 2016-03-04)<br />
* Charna Hume (Daniel Bailey, 2016-03-04)<br />
* Charlotte Godley (Daniel Bailey, 2016-03-04)</div>Danieljabaileyhttp://wiki.makespace.org/Equipment/3D_Printer/UM2Equipment/3D Printer/UM22016-02-11T21:00:17Z<p>Danieljabailey: /* Trainers */ Added me as trainer</p>
<hr />
<div>{{RedTool}}<br />
<br />
== Ultimaker 2 ==<br />
<br />
[[File:UltimakerWithLid.png|left]]<br />
<br />
The Ultimaker 2 is the newest FDM printer at MS. Its design is of a later generation than our [[Equipment/3D_Printer/Makerbot|Makerbot Replicator 2X]] and [[Equipment/3D_Printer/Up|UP!]]. The method of printing is almost identical but the implementation is more refined, so as a result the UM2 is expected to be faster, quieter and more reliable (in terms of both print outcome and maintenance).<br />
<br />
The manufacturer's product information page is [https://ultimaker.com/en/products/ultimaker-2-family/ultimaker-2 here].<br />
<br />
== Owners ==<br />
<br />
The Owners are those nominally in charge of the equipment, organising its maintenance, training others to use it, and generally being a point of contact. <br />
<br />
The current Owners of the Ultimaker are:<br />
* Mat Cook<br />
* Paul Edgington<br />
* [[User:StephenHarrison|Stephen Harrison]]<br />
* Tom Parker<br />
* Alberto Santos<br />
* John Sidiropoulos<br />
* [[User:Robv|Rob Voisey]]<br />
* [[User:Danieljabailey|Daniel Bailey]]<br />
If you have any questions, problems or concerns around the 3D printer, these are the people to contact.<br />
<br />
== Trainers ==<br />
<br />
The Trainers are not in charge of maintaining equipment, but have been more thoroughly instructed in its use and can train others. They may run extra classes for recently trained learners.<br />
<br />
The current Trainers for the Ultimaker are:<br />
* [[User:Robv|Rob Voisey]]<br />
* Paul Edgington<br />
* [[User:StephenHarrison|Stephen Harrison]]<br />
* [[User:Danieljabailey|Daniel Bailey]]<br />
<br />
== Training ==<br />
<br />
<div style="background:#FADADD; border:1px solid #FFC0CB; padding:5px"><br />
<b>YOU CAN ONLY USE THE ULTIMAKER IF YOU HAVE BEEN TRAINED</b><br><br />
and have been added to the [[Equipment/3D Printer/UM2Training#Trained_Users|UM2 Trained Users]] list by one of the Owners or Trainers<br />
</div><br />
<br />
To get trained on the Ultimaker and be added to the qualified user list, you will need to arrange for a training session with one of the owners. <br />
<br />
If you'd like to arrange training, please see:<br />
* [[Equipment/3D Printer/UM2Training|UM2 Printer Training]]<br />
<br />
Note that persons who were previously trained on the Makerbot and UP! can attend a short conversion course to be signed off on the Ultimaker. Such members should not use the Ultimaker without having done this.<br />
<br />
== General Health and Safety ==<br />
<br />
The Ultimaker is an expensive tool with a (small) risk of injury and fire, so is very important you know how to use it to avoid damaging yourself and the machine. The Ultimaker is a potentially dangerous piece of equipment which must only be operated by members who have received appropriate training and who take due care. The top things to always remember when using the Ultimaker are:<br />
<br />
* '''ONLY USE THE ULTIMAKER IF YOU HAVE BEEN TRAINED'''<br />
* '''ONLY USE THE ULTIMAKER IF YOU HAVE READ THE INSTRUCTIONS'''<br />
<br />
As a responsible user, you should be very aware of the following risks and how to deal with them:<br />
<br />
'''HEAD CRASH''' - incorrect calibration could cause the nozzle to hit the platen at job start<br />
* Pay close to attention to the start of the job and be prepared to immediately abort the job if necessary<br />
<br />
'''TRAPPING''' - The head and bed of the machine are moved by programs in the machine's memory.<br />
* Be careful when near the machine, it will possibly move even if the PC is off<br />
* Ensure you are familiar with the 'Pause' and 'Abort printing' functions on the Ultimaker so that in an emergency you can quickly halt printing.<br />
<br />
'''BURN RISK''' - the platen on the printer is heated, and will reach temperatures up to 100C during a print run which could cause skin burns. The extrusion nozzle can reach temperatures of up to 260C. Do not touch either of these areas while printing, and keep the guard door securely closed while printing.<br />
* Be careful when the machine has recently been used, especially when removing your print, as it may still be hot enough to burn<br />
<br />
'''ELECTROCUTION''' - as with all mains powered devices there is a small risk of danger from exposed wires. Always do a manual check that the wiring is safe, no cores are exposed or wires trapped.<br />
<br />
'''FUMES''' - In high concentrations ABS fumes may cause irritation. Do not spend extended periods over the printer whilst it is printing, and turn on the extractor/inlet fans of the main space when doing long print runs.<br />
<br />
== Plastics used in the printer ==<br />
<br />
'''IMPORTANT''' The Ultimaker uses 2.85mm diameter filament. This must not be confused with the 1.75mm filament used by the other FDM printers at MS.<br />
<br />
The Ultimaker can print with three different thermoplastics; PLA (Polylactic Acid), ABS (Acrylonitrile Butadiene Styrene) and CPE. It is important to select the correct material on the printer control panel when loading filament as the printing parameters vary significantly.<br />
<br />
'''PLA''' has a relatively low melting point and is capable of producing high quality prints at very fast speeds. It produces very few fumes and the odour from the melted material is actually quite pleasant. Prints are durable but not as strong as ABS, nonetheless this tends to be the material of choice for printing on the Ultimaker. PLA is available is a wide array of colours and finishes including metallic, glittery and stone effect.<br />
<br />
'''ABS''' has a higher melting point than PLA and can be hard to get to stick to the platen. It generally requires a hot platen and raised/consistent ambient (which is why we have added a door and lid to the Ultimaker). Although more difficult to work with the resultant prints can be very strong.<br />
<br />
'''CPE''' is a newer material with similar properties to ABS but without the fumes. This material needs to be printed at a high temperature which causes rapid wear of certain components in the extruder. For this reason we do not stock CPE and request that you contact an owner before using it.<br />
<br />
The communal stock is kept in plastic boxes under the printers. Plastic filament is susceptible to absorption of moisture (i.e. it is hygroscopic) which causes it to expand and jam in the printer. For this reason the boxes have been fitted with a recirculating dehumidification system. It is important that the lids are removed for the shortest time possible, and that filament is returned to the box as quickly as possible when printing is complete. This will minimise wastage and reduce our costs.<br />
<br />
== Specific Safety Tips ==<br />
<br />
There is a burn hazard from the nozzles and the heated platter, as mentioned above. The Ultimaker will display its current temperatures but you should not rely on this. The head may also move unexpectedly. Do not open the front door or place any part of your person inside the machine during or immediately prior to printing. ABS fumes over a long period may be harmful - if you feel light-headed take a break in a well ventilated area.<br />
<br />
3D printing can be a lengthy process and you are not required to stand by the printer for the whole duration. You should, however, be present for the first few minutes, monitor your print using the webcam, and whenever possible be nearby to abort a failed print. If you spot the printer unattended with a failed print (this is obvious when it happens, with a rats nest of filament quickly forming) you are encouraged to abort the print on behalf of its creator.<br />
<br />
Always switch the printer off at the back when you are finished.<br />
<br />
== Avoiding Damage to the Machine ==<br />
<br />
The bed is made from glass. Use only plastic implements to remove your prints to minimise the risk of damaging the glass. Should you need to remove the bed for any reason (it is held in with clips) take care handling it and perform a bed levelling operation when you refit it.<br />
<br />
The bed should generally be kept clean and free from dust. Wipe only with a lint free cloth (micro fibre cloths are provided) and avoid touching the build surface with your skin.<br />
<br />
== Using SD cards with the Ultimaker == <br />
<br />
The Ultimaker 2 does not yet support direct connection to a PC (this may come as a future upgrade) so you must copy your sliced (G-code) file to a DOS formatted SD card using the SD card writer attached to the PC, and then insert the card into the printer. We have found the Ultimaker to work with most modern cards. Some SD cards are available next to the printer - please remember to return them after use.<br />
<br />
== Remote access - Watch the printer via the Internet == <br />
<br />
You can view your Ultimaker print remotely, this allows you to check that the print hasn't failed and to monitor when the printer is finished before returning to the space to collect your print.<br />
<br />
Navigate to [http://makespace.ddns.net:8000/ http://makespace.ddns.net:8000] and select the Control tab. <br />
<br />
* You do not need to be logged into OctoPrint to view the camera, anybody can view it (you may wish to cover the camera if you are printing sensitive projects).<br />
* Internet Explorer doesn't appear to support the streaming video, Use Chrome or FireFox (untested with other browsers).<br />
* It's can be a little slow to load and may be unresponsive when multiple people are connected.<br />
* The url will only work outside of the Makespace network.<br />
<br />
We use OctoPrint for the streaming, hopefully in future we will get OctoPrint more integrated with the Ultimaker so you can cancel your print remotely if you notice it has failed, however for now only viewing is possible.<br />
<br />
== Ultimaker Tips == <br />
<br />
'''Blocked nozzle when loading filament:'''<br />
<br />
We've had a number of blockages reported when members are trying to load the filament. Sometimes this is not actually the nozzle being blocked but the filament feed pipe not being fully homed into the extruder. If you have problems getting the filament to load check the feed pipe where it enters the extruder, if you notice a ring around the pipe above the white press fit fitting then the pipe has not been fitted correctly and the filament will hit the inside of the extruder before it even gets to the PTFE coupler.<br />
<br />
[[File:FeedpipeInsertion.png]]<br />
<br />
You may resolve the issue by un-clipping the white push-fit fitting, pressing down and removing the pipe then carefully re-inserting it ensuring it is straight and fully homed. You should not see any rings around the pipe when it is fully homed and inspection of the middle of the extruder you should see the pipe butted up against the white PTFE coupler between the extruder body and nozzle.<br />
<br />
This problem may be more apparent if you are using filament that is nearing the end of the reel where the filament becomes very curved. Try a different filament that is straighter.<br />
<br />
'''Blocked nozzle / feed failure during printing'''<br />
<br />
The UM2 printer is prone to nozzle blockage when switching from ABS to PLA filament (or from any higher temperature material to a lower temperature material). The reason is that a quantity of ABS remains inside the extruder after loading PLA, because the lower extrusion temperature for PLA does not completely melt the unwanted material. Often this doesn't prevent initial loading of PLA because the material change cycle heats the nozzle to a higher temperature, but during printing the feed can be reduced or blocked entirely.<br />
<br />
In the near future we hope to solve this with a second 3D printer with one assigned to PLA and the other to ABS. In the mean time there is a procedure you can use to remove unwanted material from the nozzle. It is recommended that this is done every time you move from ABS to PLA. Ideally the ABS user would do so upon completion of their print.<br />
<br />
Instructions here: [https://ultimaker.com/en/support/149-atomic-method Ultimaker Atomic Method]<br />
<br />
There are some important notes:<br />
<br />
1. Take great care not to lose the little blue bowden tube clamp clip. It has a tendency to ping across the room!<br />
<br />
2. The instructions say to use a quick firm pull to remove the filament. They mean it! If you pull slowly the filament will simply stretch and you'll have to start over.<br />
<br />
3. On reassembly ensure that the bowden tube is pushed fully into position. See above!<br />
<br />
'''General 3D printing Quality Tips'''<br />
<br />
Check out the excellent [https://www.simplify3d.com/support/print-quality-troubleshooting/ 3D printing quality troubleshooting guide] from Simplify 3D<br />
<br />
'''Cura software tips'''<br />
<br />
[https://ultimaker.com/en/products/cura-software Download Ultimaker Cura Software]<br />
<br />
The Cura software remembers the previous settings used for a print and in some cases carries the advanced settings over to the basic option but doesn't display it (e.g. Brim). This can cause problems in a shared environment that the Ultimaker PC lives in as you may not get appropriate printing settings for your print if the last person adjusted them. <br />
<br />
As the Ultimaker prints from an SD card and material settings are set on the printer itself you may prefer to install the Cura software on your own computer and save the file to an SD Card rather than using the Ultimaker PC to ensure you have settings that work best for your use case.<br />
<br />
We are currently running 15.06 of the Cura software, this is a beta version and does not have many of the functions of the 15.04 version. For advanced users you may prefer 15.04 which has more functionality and includes advanced things such as repeat printing a design on the same plate spaced automatically so not to clash.<br />
<br />
'''Filament not on a reel'''<br />
<br />
Short lengths of filament are sold by many places rather than a full reel worth, we have a makespace laser cut acrylic reel that you can use to roll these onto and place on the back of the ultimaker. It has a larger diameter center to help. Currently this can be found in the cardboard box on the shelf above the Ultimaker.<br />
<br />
'''Ultimaker Lid'''<br />
<br />
Ultimaker do not provide a lid for the UM2 so we have a laser cut acrylic MakeSpace made one. Please be gentle with it!<br />
<br />
If you have problems with the lid please report it to the Ultimaker Owners to allow us to improve the design and fix issues.<br />
<br />
You should not need to remove the lid in normal day to day use. If you do remove it please ensure you replace it as it keeps dust from getting onto the plate (which messes up the print - Makespace is VERY dusty!) and helps keep the printing environment temperature better which should help improve your prints.<br />
<br />
'''ABS Printing'''<br />
<br />
The default setting for the Ultimaker bed is fairly low for ABS, we have found prints do not stick well at this temperature.<br />
<br />
* When loading ABS check the bed temperature displayed on the screen when selecting the material<br />
* A custom option is pre-defined for ABS with a higher bed temperature, we recommend around 110°C bed temperature for ABS.<br />
* If you selected the wrong option when loading the filament the bed temperature can be adjusted when printing through the "Tune" menu option.<br />
<br />
'''Ultimaker Community'''<br />
<br />
Be sure to check out the [https://ultimaker.com/en/community/dashboard Ultimaker Community site] it is very active and a great resource.<br />
<br />
== Filament storage == <br />
<br />
We have a few dedicated filament storage boxes for the Ultimaker. These boxes are humidity controlled and have a Silica gel cartridge fitted to the lid to remove moisture. Yes, they are internet connected to allow the owners to monitor the humidity level and replace the silica gel when required. We aim to keep the humidity level below 15% in the box.<br />
<br />
* Ensure the lid is kept closed on the filament storage boxes, leaving the lid off will degrade the silica gel quickly.<br />
* Be sure to return the filament to the correct storage box after use to prevent undue exposure to moisture in the air which can ruin the filament.<br />
* Do not store your own filament in the filament boxes. Personal filament should be stored in your own MakeSpace box. <br />
** Keep your filament in a sealed plastic bag (or wrap with clingfilm).<br />
** We have a supply of Silica gel on the shelf above the Ultimaker, you may wish to add a scoop or two into your bag to keep the moisture down. Use only the Orange colour silica gel. Green/Brown gel needs to be cooked to remove moisture. <br />
** Do not eat the silica gel!!!<br />
<br />
== Maintenance == <br />
<br />
See [[Ultimaker Maintenance]]<br />
<br />
-----------------<br />
<br />
TO BE COMPLETED ASAP</div>Danieljabaileyhttp://wiki.makespace.org/Equipment/3D_Printer/UM2Equipment/3D Printer/UM22016-02-11T20:59:50Z<p>Danieljabailey: /* Owners */ Added me as owner.</p>
<hr />
<div>{{RedTool}}<br />
<br />
== Ultimaker 2 ==<br />
<br />
[[File:UltimakerWithLid.png|left]]<br />
<br />
The Ultimaker 2 is the newest FDM printer at MS. Its design is of a later generation than our [[Equipment/3D_Printer/Makerbot|Makerbot Replicator 2X]] and [[Equipment/3D_Printer/Up|UP!]]. The method of printing is almost identical but the implementation is more refined, so as a result the UM2 is expected to be faster, quieter and more reliable (in terms of both print outcome and maintenance).<br />
<br />
The manufacturer's product information page is [https://ultimaker.com/en/products/ultimaker-2-family/ultimaker-2 here].<br />
<br />
== Owners ==<br />
<br />
The Owners are those nominally in charge of the equipment, organising its maintenance, training others to use it, and generally being a point of contact. <br />
<br />
The current Owners of the Ultimaker are:<br />
* Mat Cook<br />
* Paul Edgington<br />
* [[User:StephenHarrison|Stephen Harrison]]<br />
* Tom Parker<br />
* Alberto Santos<br />
* John Sidiropoulos<br />
* [[User:Robv|Rob Voisey]]<br />
* [[User:Danieljabailey|Daniel Bailey]]<br />
If you have any questions, problems or concerns around the 3D printer, these are the people to contact.<br />
<br />
== Trainers ==<br />
<br />
The Trainers are not in charge of maintaining equipment, but have been more thoroughly instructed in its use and can train others. They may run extra classes for recently trained learners.<br />
<br />
The current Trainers for the Ultimaker are:<br />
* [[User:Robv|Rob Voisey]]<br />
* Paul Edgington<br />
* [[User:StephenHarrison|Stephen Harrison]]<br />
<br />
== Training ==<br />
<br />
<div style="background:#FADADD; border:1px solid #FFC0CB; padding:5px"><br />
<b>YOU CAN ONLY USE THE ULTIMAKER IF YOU HAVE BEEN TRAINED</b><br><br />
and have been added to the [[Equipment/3D Printer/UM2Training#Trained_Users|UM2 Trained Users]] list by one of the Owners or Trainers<br />
</div><br />
<br />
To get trained on the Ultimaker and be added to the qualified user list, you will need to arrange for a training session with one of the owners. <br />
<br />
If you'd like to arrange training, please see:<br />
* [[Equipment/3D Printer/UM2Training|UM2 Printer Training]]<br />
<br />
Note that persons who were previously trained on the Makerbot and UP! can attend a short conversion course to be signed off on the Ultimaker. Such members should not use the Ultimaker without having done this.<br />
<br />
== General Health and Safety ==<br />
<br />
The Ultimaker is an expensive tool with a (small) risk of injury and fire, so is very important you know how to use it to avoid damaging yourself and the machine. The Ultimaker is a potentially dangerous piece of equipment which must only be operated by members who have received appropriate training and who take due care. The top things to always remember when using the Ultimaker are:<br />
<br />
* '''ONLY USE THE ULTIMAKER IF YOU HAVE BEEN TRAINED'''<br />
* '''ONLY USE THE ULTIMAKER IF YOU HAVE READ THE INSTRUCTIONS'''<br />
<br />
As a responsible user, you should be very aware of the following risks and how to deal with them:<br />
<br />
'''HEAD CRASH''' - incorrect calibration could cause the nozzle to hit the platen at job start<br />
* Pay close to attention to the start of the job and be prepared to immediately abort the job if necessary<br />
<br />
'''TRAPPING''' - The head and bed of the machine are moved by programs in the machine's memory.<br />
* Be careful when near the machine, it will possibly move even if the PC is off<br />
* Ensure you are familiar with the 'Pause' and 'Abort printing' functions on the Ultimaker so that in an emergency you can quickly halt printing.<br />
<br />
'''BURN RISK''' - the platen on the printer is heated, and will reach temperatures up to 100C during a print run which could cause skin burns. The extrusion nozzle can reach temperatures of up to 260C. Do not touch either of these areas while printing, and keep the guard door securely closed while printing.<br />
* Be careful when the machine has recently been used, especially when removing your print, as it may still be hot enough to burn<br />
<br />
'''ELECTROCUTION''' - as with all mains powered devices there is a small risk of danger from exposed wires. Always do a manual check that the wiring is safe, no cores are exposed or wires trapped.<br />
<br />
'''FUMES''' - In high concentrations ABS fumes may cause irritation. Do not spend extended periods over the printer whilst it is printing, and turn on the extractor/inlet fans of the main space when doing long print runs.<br />
<br />
== Plastics used in the printer ==<br />
<br />
'''IMPORTANT''' The Ultimaker uses 2.85mm diameter filament. This must not be confused with the 1.75mm filament used by the other FDM printers at MS.<br />
<br />
The Ultimaker can print with three different thermoplastics; PLA (Polylactic Acid), ABS (Acrylonitrile Butadiene Styrene) and CPE. It is important to select the correct material on the printer control panel when loading filament as the printing parameters vary significantly.<br />
<br />
'''PLA''' has a relatively low melting point and is capable of producing high quality prints at very fast speeds. It produces very few fumes and the odour from the melted material is actually quite pleasant. Prints are durable but not as strong as ABS, nonetheless this tends to be the material of choice for printing on the Ultimaker. PLA is available is a wide array of colours and finishes including metallic, glittery and stone effect.<br />
<br />
'''ABS''' has a higher melting point than PLA and can be hard to get to stick to the platen. It generally requires a hot platen and raised/consistent ambient (which is why we have added a door and lid to the Ultimaker). Although more difficult to work with the resultant prints can be very strong.<br />
<br />
'''CPE''' is a newer material with similar properties to ABS but without the fumes. This material needs to be printed at a high temperature which causes rapid wear of certain components in the extruder. For this reason we do not stock CPE and request that you contact an owner before using it.<br />
<br />
The communal stock is kept in plastic boxes under the printers. Plastic filament is susceptible to absorption of moisture (i.e. it is hygroscopic) which causes it to expand and jam in the printer. For this reason the boxes have been fitted with a recirculating dehumidification system. It is important that the lids are removed for the shortest time possible, and that filament is returned to the box as quickly as possible when printing is complete. This will minimise wastage and reduce our costs.<br />
<br />
== Specific Safety Tips ==<br />
<br />
There is a burn hazard from the nozzles and the heated platter, as mentioned above. The Ultimaker will display its current temperatures but you should not rely on this. The head may also move unexpectedly. Do not open the front door or place any part of your person inside the machine during or immediately prior to printing. ABS fumes over a long period may be harmful - if you feel light-headed take a break in a well ventilated area.<br />
<br />
3D printing can be a lengthy process and you are not required to stand by the printer for the whole duration. You should, however, be present for the first few minutes, monitor your print using the webcam, and whenever possible be nearby to abort a failed print. If you spot the printer unattended with a failed print (this is obvious when it happens, with a rats nest of filament quickly forming) you are encouraged to abort the print on behalf of its creator.<br />
<br />
Always switch the printer off at the back when you are finished.<br />
<br />
== Avoiding Damage to the Machine ==<br />
<br />
The bed is made from glass. Use only plastic implements to remove your prints to minimise the risk of damaging the glass. Should you need to remove the bed for any reason (it is held in with clips) take care handling it and perform a bed levelling operation when you refit it.<br />
<br />
The bed should generally be kept clean and free from dust. Wipe only with a lint free cloth (micro fibre cloths are provided) and avoid touching the build surface with your skin.<br />
<br />
== Using SD cards with the Ultimaker == <br />
<br />
The Ultimaker 2 does not yet support direct connection to a PC (this may come as a future upgrade) so you must copy your sliced (G-code) file to a DOS formatted SD card using the SD card writer attached to the PC, and then insert the card into the printer. We have found the Ultimaker to work with most modern cards. Some SD cards are available next to the printer - please remember to return them after use.<br />
<br />
== Remote access - Watch the printer via the Internet == <br />
<br />
You can view your Ultimaker print remotely, this allows you to check that the print hasn't failed and to monitor when the printer is finished before returning to the space to collect your print.<br />
<br />
Navigate to [http://makespace.ddns.net:8000/ http://makespace.ddns.net:8000] and select the Control tab. <br />
<br />
* You do not need to be logged into OctoPrint to view the camera, anybody can view it (you may wish to cover the camera if you are printing sensitive projects).<br />
* Internet Explorer doesn't appear to support the streaming video, Use Chrome or FireFox (untested with other browsers).<br />
* It's can be a little slow to load and may be unresponsive when multiple people are connected.<br />
* The url will only work outside of the Makespace network.<br />
<br />
We use OctoPrint for the streaming, hopefully in future we will get OctoPrint more integrated with the Ultimaker so you can cancel your print remotely if you notice it has failed, however for now only viewing is possible.<br />
<br />
== Ultimaker Tips == <br />
<br />
'''Blocked nozzle when loading filament:'''<br />
<br />
We've had a number of blockages reported when members are trying to load the filament. Sometimes this is not actually the nozzle being blocked but the filament feed pipe not being fully homed into the extruder. If you have problems getting the filament to load check the feed pipe where it enters the extruder, if you notice a ring around the pipe above the white press fit fitting then the pipe has not been fitted correctly and the filament will hit the inside of the extruder before it even gets to the PTFE coupler.<br />
<br />
[[File:FeedpipeInsertion.png]]<br />
<br />
You may resolve the issue by un-clipping the white push-fit fitting, pressing down and removing the pipe then carefully re-inserting it ensuring it is straight and fully homed. You should not see any rings around the pipe when it is fully homed and inspection of the middle of the extruder you should see the pipe butted up against the white PTFE coupler between the extruder body and nozzle.<br />
<br />
This problem may be more apparent if you are using filament that is nearing the end of the reel where the filament becomes very curved. Try a different filament that is straighter.<br />
<br />
'''Blocked nozzle / feed failure during printing'''<br />
<br />
The UM2 printer is prone to nozzle blockage when switching from ABS to PLA filament (or from any higher temperature material to a lower temperature material). The reason is that a quantity of ABS remains inside the extruder after loading PLA, because the lower extrusion temperature for PLA does not completely melt the unwanted material. Often this doesn't prevent initial loading of PLA because the material change cycle heats the nozzle to a higher temperature, but during printing the feed can be reduced or blocked entirely.<br />
<br />
In the near future we hope to solve this with a second 3D printer with one assigned to PLA and the other to ABS. In the mean time there is a procedure you can use to remove unwanted material from the nozzle. It is recommended that this is done every time you move from ABS to PLA. Ideally the ABS user would do so upon completion of their print.<br />
<br />
Instructions here: [https://ultimaker.com/en/support/149-atomic-method Ultimaker Atomic Method]<br />
<br />
There are some important notes:<br />
<br />
1. Take great care not to lose the little blue bowden tube clamp clip. It has a tendency to ping across the room!<br />
<br />
2. The instructions say to use a quick firm pull to remove the filament. They mean it! If you pull slowly the filament will simply stretch and you'll have to start over.<br />
<br />
3. On reassembly ensure that the bowden tube is pushed fully into position. See above!<br />
<br />
'''General 3D printing Quality Tips'''<br />
<br />
Check out the excellent [https://www.simplify3d.com/support/print-quality-troubleshooting/ 3D printing quality troubleshooting guide] from Simplify 3D<br />
<br />
'''Cura software tips'''<br />
<br />
[https://ultimaker.com/en/products/cura-software Download Ultimaker Cura Software]<br />
<br />
The Cura software remembers the previous settings used for a print and in some cases carries the advanced settings over to the basic option but doesn't display it (e.g. Brim). This can cause problems in a shared environment that the Ultimaker PC lives in as you may not get appropriate printing settings for your print if the last person adjusted them. <br />
<br />
As the Ultimaker prints from an SD card and material settings are set on the printer itself you may prefer to install the Cura software on your own computer and save the file to an SD Card rather than using the Ultimaker PC to ensure you have settings that work best for your use case.<br />
<br />
We are currently running 15.06 of the Cura software, this is a beta version and does not have many of the functions of the 15.04 version. For advanced users you may prefer 15.04 which has more functionality and includes advanced things such as repeat printing a design on the same plate spaced automatically so not to clash.<br />
<br />
'''Filament not on a reel'''<br />
<br />
Short lengths of filament are sold by many places rather than a full reel worth, we have a makespace laser cut acrylic reel that you can use to roll these onto and place on the back of the ultimaker. It has a larger diameter center to help. Currently this can be found in the cardboard box on the shelf above the Ultimaker.<br />
<br />
'''Ultimaker Lid'''<br />
<br />
Ultimaker do not provide a lid for the UM2 so we have a laser cut acrylic MakeSpace made one. Please be gentle with it!<br />
<br />
If you have problems with the lid please report it to the Ultimaker Owners to allow us to improve the design and fix issues.<br />
<br />
You should not need to remove the lid in normal day to day use. If you do remove it please ensure you replace it as it keeps dust from getting onto the plate (which messes up the print - Makespace is VERY dusty!) and helps keep the printing environment temperature better which should help improve your prints.<br />
<br />
'''ABS Printing'''<br />
<br />
The default setting for the Ultimaker bed is fairly low for ABS, we have found prints do not stick well at this temperature.<br />
<br />
* When loading ABS check the bed temperature displayed on the screen when selecting the material<br />
* A custom option is pre-defined for ABS with a higher bed temperature, we recommend around 110°C bed temperature for ABS.<br />
* If you selected the wrong option when loading the filament the bed temperature can be adjusted when printing through the "Tune" menu option.<br />
<br />
'''Ultimaker Community'''<br />
<br />
Be sure to check out the [https://ultimaker.com/en/community/dashboard Ultimaker Community site] it is very active and a great resource.<br />
<br />
== Filament storage == <br />
<br />
We have a few dedicated filament storage boxes for the Ultimaker. These boxes are humidity controlled and have a Silica gel cartridge fitted to the lid to remove moisture. Yes, they are internet connected to allow the owners to monitor the humidity level and replace the silica gel when required. We aim to keep the humidity level below 15% in the box.<br />
<br />
* Ensure the lid is kept closed on the filament storage boxes, leaving the lid off will degrade the silica gel quickly.<br />
* Be sure to return the filament to the correct storage box after use to prevent undue exposure to moisture in the air which can ruin the filament.<br />
* Do not store your own filament in the filament boxes. Personal filament should be stored in your own MakeSpace box. <br />
** Keep your filament in a sealed plastic bag (or wrap with clingfilm).<br />
** We have a supply of Silica gel on the shelf above the Ultimaker, you may wish to add a scoop or two into your bag to keep the moisture down. Use only the Orange colour silica gel. Green/Brown gel needs to be cooked to remove moisture. <br />
** Do not eat the silica gel!!!<br />
<br />
== Maintenance == <br />
<br />
See [[Ultimaker Maintenance]]<br />
<br />
-----------------<br />
<br />
TO BE COMPLETED ASAP</div>Danieljabaileyhttp://wiki.makespace.org/Equipment/3D_Printer/UM2TrainingEquipment/3D Printer/UM2Training2016-02-11T20:50:39Z<p>Danieljabailey: /* Trained Users */ Added users trained on 2016-02-11</p>
<hr />
<div>[[Equipment|Equipment]] / [[Equipment/3D Printer|UM2]] / Training<br />
<br />
= Ultimaker 2 3D Printer Training =<br />
<br />
This page documents the process for being trained on the Ultimaker 2 Printer, and the list of members who have completed that training.<br />
<br />
== Summary ==<br />
<br />
Training takes place in three main steps:<br />
* Group Training of 1-4 members, going through the equipment and how to use it (~1hr)<br />
* Individual Training Task, where an individual member is set a task to complete to prove and improve understanding (~20min each)<br />
* Recommended project oversight, where more experienced users oversee the projects being undertaken when cutting (first 2-3 projects)<br />
<br />
A shorter conversion training session is available for members who were previously signed off to use the Makerbot 2X printer. These sessions last around 20 minutes and do not include individual sessions.<br />
<br />
== Booking ==<br />
<br />
For discussing and arranging slots, please use the mailing list. New training sessions will be announced on the Meetup group.<br />
<br />
Notes:<br />
* You can only be trained if you have RSVP'd to a Meetup session<br />
<br />
== Training Cheatsheet - Conversion Course ==<br />
<br />
Members already trained on and familiar with the Makerbot 2X can attend this short conversion course to be signed off to use the Ultimaker 2 3D printer. Up to 10 people can be accommodated on each course, which lasts 20 to 30 minutes.<br />
<br />
1. Physical Differences from the 2X<br />
* Glass build plate, no kapton tape<br />
* Single extruder<br />
* Push feed<br />
<br />
2. General<br />
* Use the correct filament (2.85mm, NOT 3mm or 1.75mm)<br />
* New filament storage system<br />
<br />
3. Printing<br />
* Fence / Brim / Raft<br />
* OK to leave printer unattended after the first few layers<br />
* Camera available for remote monitoring<br />
* Use only plastic implements for part removal, take care not to melt them on the hot end<br />
<br />
4. Cura Software<br />
* Import and place<br />
* Simple mode<br />
* Brief overview of advanced mode<br />
* Temperature set on printer not slicer<br />
* Exporting to SD card<br />
<br />
5. Unload / Load filament<br />
* How to feed (slow first, then fast)<br />
* Select correct material in menu<br />
* Changing temperature and speed parameters from printer<br />
* Demonstrate the atomic method of cleaning the extruder to prevent feed jams<br />
<br />
6. Filament pricing<br />
* 5p per gram for PLA and ABS, to be kept under review<br />
* Include wastage!<br />
<br />
== Training Cheatsheet - Full Course ==<br />
<br />
'''Group Session'''<br />
<br />
1. Ask what each member hopes to get out of the 3D printer.<br />
<br />
2. Explain how 3D printing works<br />
<br />
3. Safety<br />
* Burn hazard – nozzle and build plate<br />
* Unit may move unexpectedly<br />
* Avoid prolonged exposure to ABS fumes<br />
<br />
4. Damage to machine<br />
* Fragile build plate<br />
* Jammed filament<br />
<br />
5. General<br />
* Use the correct filament (2.85mm)<br />
* Filament storage and feed system<br />
* Switch off when finished<br />
* Leave levelling to the owners but report any problems<br />
<br />
6. PLA vs ABS<br />
* How to tell the difference<br />
* Different temperature<br />
* PLA Biodegradable<br />
<br />
7. Software / workflow<br />
* Importing<br />
* Positioning on bed<br />
* Supports<br />
* Setting quality / speed trade off<br />
* Advanced options<br />
* Exporting to SD card<br />
<br />
8. Unload / load<br />
* Attaching spool or loading from storage box<br />
* Feeding (slow then fast)<br />
* Beware of wrapping round axle<br />
* Setting material in menu<br />
* Adjusting parameters, e.g. ABS plate temperature<br />
<br />
9. Printing<br />
* Preheating<br />
* Fence printing<br />
* Keep an eye on progress, locally or with camera<br />
* If leaving unattended, put a post-it with your contact details<br />
* Use only plastic implements for part removal<br />
<br />
10. Other stuff<br />
* Demonstrate atomic method of cleaning the nozzle to prevent feed jams<br />
* Strength characteristics – orientation is important<br />
* Paying<br />
<br />
'''Individual Training Task'''<br />
<br />
Task<br />
* Should demonstrate import, setup, position and run<br />
* Choose a part that takes about 10 mins to print (preloaded on PC)<br />
<br />
Steps<br />
* Set individual to work, don't prompt but do answer questions (or pose if needed)<br />
* Talk through design once done, question/check things etc<br />
* Proceed to printing (watch carefully all steps)<br />
<br />
Assuming all ok:<br />
* Get them to read the health and safety notes about operation and materials<br />
* Add to the trained member list<br />
<br />
'''Project Oversight'''<br />
<br />
For next 2-3 projects, recommend member will find another more experienced trained user to support them (second pair of eyes)<br />
<br />
This cheat-sheet is available in PDF form on a single side of A4 [http://wiki.makespace.org/File:TrainingCheatsheetUM2.pdf here].<br />
<br />
== Trained Users ==<br />
<br />
The following members of Makespace are trained and qualified to use the 3D Printer (note, they are not qualified to train others however):<br />
<br />
* Paul Osborn (Rob Voisey, 2015-07-30)<br />
* Julius Schmidt (Rob Voisey, 2015-07-30)<br />
* Peter Knight (Rob Voisey, 2015-07-30)<br />
* Adam Mulligan (Rob Voisey, 2015-07-30)<br />
* Charlotte Harvey (Rob Voisey, 2015-07-30)<br />
* Alex Gee (Rob Voisey, 2015-07-30)<br />
* Albert Santos (Rob Voisey, 2015-07-30)<br />
* Zizwani Mhango (Rob Voisey, 2015-07-30)<br />
* Christie Nel (Rob Voisey, 2015-07-30)<br />
* Robert Karpinski (Rob Voisey, 2015-07-30)<br />
* Alexis Mather (Stephen Harrison, 2015-08-03)<br />
* Ben Wheatley (Stephen Harrison, 2015-08-03)<br />
* Stevan Wing (Stephen Harrison, 2015-08-03)<br />
* Jae Tumer (Stephen Harrison, 2015-08-03)<br />
* Jennifer Herbert (Stephen Harrison, 2015-08-03)<br />
* Frodi Jones (Stephen Harrison, 2015-08-03)<br />
* Matt Wayland (Stephen Harrison, 2015-08-03)<br />
* Marco Aite (Stephen Harrison, 2015-08-03)<br />
* Graeham Douglas (Stephen Harrison, 2015-08-03)<br />
* Robin Sterling (Stephen Harrison, 2015-08-07)<br />
* Abhi Manyu (Stephen Harrison, 2015-08-07)<br />
* Ward Hills (Stephen Harrison, 2015-08-07)<br />
* Carols A. Lugo (Stephen Harrison, 2015-08-07)<br />
* Ben Alper (Stephen Harrison, 2015-08-07)<br />
* Jon Green (Stephen Harrison, 2015-08-07)<br />
* Marcin Izo (Stephen Harrison, 2015-08-07)<br />
* Steve Upton (Rob Voisey, 2015-08-11)<br />
* Frederic Sorgeloos (Rob Voisey, 2015-08-11)<br />
* Andrew Cooke (Rob Voisey, 2015-08-11)<br />
* Ned Booker (Rob Voisey, 2015-08-11)<br />
* Daryl Stewart (Paul Edgington, 2015-08-24)<br />
* Nacho Lopez (Paul Edgington, 2015-08-24)<br />
* Ed Robertson (Paul Edgington, 2015-08-24)<br />
* Clive Beale (Paul Edgington, 2015-08-24)<br />
* Oliver Fleck (Paul Edgington, 2015-08-24)<br />
* Mark Cheverton (Rob Voisey, 2015-09-08)<br />
* Nik (Rob Voisey, 2015-09-08)<br />
* Dan Tidhar (Rob Voisey, 2015-09-08)<br />
* Tobias Wenzel (Rob Voisey, 2015-09-08)<br />
* Brian Starkey (Rob Voisey, 2015-09-08)<br />
* Jonathan Waite (Rob Voisey, 2015-09-08)<br />
* Emyr James (Rob Voisey, 2015-09-08)<br />
* Richard Hall (Rob Voisey, 2015-09-08)<br />
* Andrew Dunn (Rob Voisey, 2015-09-08)<br />
* Andrea Cipri (Paul Edgington, 2015-09-30)<br />
* John Sidinopoulos (Paul Edgington, 2015-09-30)<br />
* Stuart Barton (Paul Edgington, 2015-09-30)<br />
* Mark Calleta (Paul Edgington, 2015-09-30)<br />
* Martin Lenz (Paul Edgington, 2015-09-30)<br />
* Phill Banks (Paul Edgington, 2015-10-21)<br />
* Felix Morley (Paul Edgington, 2015-10-21)<br />
* David Jordan (Paul Edgington, 2015-10-21)<br />
* Mark Roberts (Stephen Harrison, 2015-10-23)<br />
* Jenny Molloy (Stephen Harrison, 2015-10-23)<br />
* Henry Cawley (Rob Voisey, 2015-11-18)<br />
* Bogdan Spiridom (Rob Voisey, 2015-11-18)<br />
* Jakub Sanak (Rob Voisey, 2015-11-18)<br />
* Jack Brewster (Rob Voisey, 2015-11-18)<br />
* Mayke Santos (Rob Voisey, 2015-11-18)<br />
* Luis Veiga Pumar (Stephen Harrison, 2015-11-24)<br />
* Greg Matthews (Stephen Harrison, 2015-11-24)<br />
* Brian Corteil (Stephen Harrison, 2015-11-24)<br />
* Rob Rescorla (Stephen Harrison, 2015-11-24)<br />
* Leo Rones (Stephen Harrison, 2015-11-24)<br />
* Diana Probst (Stephen Harrison, 2015-11-25)<br />
* Adrian van den Heever (Stephen Harrison, 2015-11-25)<br />
* Al Napp (Stephen Harrison, 2015-11-25)<br />
* Katy Marshall (Stephen Harrison, 2015-12-01)<br />
* Peter Mottram (Stephen Harrison, 2015-12-01)<br />
* David Barham (Stephen Harrison, 2015-12-01)<br />
* Johan Henriksson (Stephen Harrison, 2015-12-01)<br />
* Fotis Fotiadis (Stephen Harrison, 2015-12-01)<br />
* Oliver Martin (Stephen Harrison, 2015-12-01)<br />
* Andrew Drummond (Stephen Harrison, 2015-12-01)<br />
* Spencer Dixon (Stephen Harrison, 2015-12-01)<br />
* Jonathan Woolf (Rob Voisey, 2016-01-07)<br />
* Daniel Bailey (Rob Voisey, 2016-01-07)<br />
* David Haines (Rob Voisey, 2016-01-07)<br />
* Giovanni Bisutii (Rob Voisey, 2016-01-07)<br />
* Simon Hartley (Daniel Bailey, 2016-02-11)<br />
* Francois Eve (Daniel Bailey, 2016-02-11)<br />
* Giovanni Orlando (Daniel Bailey, 2016-02-11)<br />
* Dan Tidhar (Daniel Bailey, 2016-02-11)</div>Danieljabaileyhttp://wiki.makespace.org/User:DanieljabaileyUser:Danieljabailey2016-02-09T20:11:21Z<p>Danieljabailey: Created me!</p>
<hr />
<div>Hi, I'm Dan.<br />
<br />
If you like, you can read my [http://bitofahack.com/ Blog]</div>Danieljabaileyhttp://wiki.makespace.org/Equipment/3D_Printer/UM2TrainingEquipment/3D Printer/UM2Training2016-02-09T20:08:59Z<p>Danieljabailey: /* Training Cheatsheet - Full Course */ Added link to PDF version of file</p>
<hr />
<div>[[Equipment|Equipment]] / [[Equipment/3D Printer|UM2]] / Training<br />
<br />
= Ultimaker 2 3D Printer Training =<br />
<br />
This page documents the process for being trained on the Ultimaker 2 Printer, and the list of members who have completed that training.<br />
<br />
== Summary ==<br />
<br />
Training takes place in three main steps:<br />
* Group Training of 1-4 members, going through the equipment and how to use it (~1hr)<br />
* Individual Training Task, where an individual member is set a task to complete to prove and improve understanding (~20min each)<br />
* Recommended project oversight, where more experienced users oversee the projects being undertaken when cutting (first 2-3 projects)<br />
<br />
A shorter conversion training session is available for members who were previously signed off to use the Makerbot 2X printer. These sessions last around 20 minutes and do not include individual sessions.<br />
<br />
== Booking ==<br />
<br />
For discussing and arranging slots, please use the mailing list. New training sessions will be announced on the Meetup group.<br />
<br />
Notes:<br />
* You can only be trained if you have RSVP'd to a Meetup session<br />
<br />
== Training Cheatsheet - Conversion Course ==<br />
<br />
Members already trained on and familiar with the Makerbot 2X can attend this short conversion course to be signed off to use the Ultimaker 2 3D printer. Up to 10 people can be accommodated on each course, which lasts 20 to 30 minutes.<br />
<br />
1. Physical Differences from the 2X<br />
* Glass build plate, no kapton tape<br />
* Single extruder<br />
* Push feed<br />
<br />
2. General<br />
* Use the correct filament (2.85mm, NOT 3mm or 1.75mm)<br />
* New filament storage system<br />
<br />
3. Printing<br />
* Fence / Brim / Raft<br />
* OK to leave printer unattended after the first few layers<br />
* Camera available for remote monitoring<br />
* Use only plastic implements for part removal, take care not to melt them on the hot end<br />
<br />
4. Cura Software<br />
* Import and place<br />
* Simple mode<br />
* Brief overview of advanced mode<br />
* Temperature set on printer not slicer<br />
* Exporting to SD card<br />
<br />
5. Unload / Load filament<br />
* How to feed (slow first, then fast)<br />
* Select correct material in menu<br />
* Changing temperature and speed parameters from printer<br />
* Demonstrate the atomic method of cleaning the extruder to prevent feed jams<br />
<br />
6. Filament pricing<br />
* 5p per gram for PLA and ABS, to be kept under review<br />
* Include wastage!<br />
<br />
== Training Cheatsheet - Full Course ==<br />
<br />
'''Group Session'''<br />
<br />
1. Ask what each member hopes to get out of the 3D printer.<br />
<br />
2. Explain how 3D printing works<br />
<br />
3. Safety<br />
* Burn hazard – nozzle and build plate<br />
* Unit may move unexpectedly<br />
* Avoid prolonged exposure to ABS fumes<br />
<br />
4. Damage to machine<br />
* Fragile build plate<br />
* Jammed filament<br />
<br />
5. General<br />
* Use the correct filament (2.85mm)<br />
* Filament storage and feed system<br />
* Switch off when finished<br />
* Leave levelling to the owners but report any problems<br />
<br />
6. PLA vs ABS<br />
* How to tell the difference<br />
* Different temperature<br />
* PLA Biodegradable<br />
<br />
7. Software / workflow<br />
* Importing<br />
* Positioning on bed<br />
* Supports<br />
* Setting quality / speed trade off<br />
* Advanced options<br />
* Exporting to SD card<br />
<br />
8. Unload / load<br />
* Attaching spool or loading from storage box<br />
* Feeding (slow then fast)<br />
* Beware of wrapping round axle<br />
* Setting material in menu<br />
* Adjusting parameters, e.g. ABS plate temperature<br />
<br />
9. Printing<br />
* Preheating<br />
* Fence printing<br />
* Keep an eye on progress, locally or with camera<br />
* If leaving unattended, put a post-it with your contact details<br />
* Use only plastic implements for part removal<br />
<br />
10. Other stuff<br />
* Demonstrate atomic method of cleaning the nozzle to prevent feed jams<br />
* Strength characteristics – orientation is important<br />
* Paying<br />
<br />
'''Individual Training Task'''<br />
<br />
Task<br />
* Should demonstrate import, setup, position and run<br />
* Choose a part that takes about 10 mins to print (preloaded on PC)<br />
<br />
Steps<br />
* Set individual to work, don't prompt but do answer questions (or pose if needed)<br />
* Talk through design once done, question/check things etc<br />
* Proceed to printing (watch carefully all steps)<br />
<br />
Assuming all ok:<br />
* Get them to read the health and safety notes about operation and materials<br />
* Add to the trained member list<br />
<br />
'''Project Oversight'''<br />
<br />
For next 2-3 projects, recommend member will find another more experienced trained user to support them (second pair of eyes)<br />
<br />
This cheat-sheet is available in PDF form on a single side of A4 [http://wiki.makespace.org/File:TrainingCheatsheetUM2.pdf here].<br />
<br />
== Trained Users ==<br />
<br />
The following members of Makespace are trained and qualified to use the 3D Printer (note, they are not qualified to train others however):<br />
<br />
* Paul Osborn (Rob Voisey, 2015-07-30)<br />
* Julius Schmidt (Rob Voisey, 2015-07-30)<br />
* Peter Knight (Rob Voisey, 2015-07-30)<br />
* Adam Mulligan (Rob Voisey, 2015-07-30)<br />
* Charlotte Harvey (Rob Voisey, 2015-07-30)<br />
* Alex Gee (Rob Voisey, 2015-07-30)<br />
* Albert Santos (Rob Voisey, 2015-07-30)<br />
* Zizwani Mhango (Rob Voisey, 2015-07-30)<br />
* Christie Nel (Rob Voisey, 2015-07-30)<br />
* Robert Karpinski (Rob Voisey, 2015-07-30)<br />
* Alexis Mather (Stephen Harrison, 2015-08-03)<br />
* Ben Wheatley (Stephen Harrison, 2015-08-03)<br />
* Stevan Wing (Stephen Harrison, 2015-08-03)<br />
* Jae Tumer (Stephen Harrison, 2015-08-03)<br />
* Jennifer Herbert (Stephen Harrison, 2015-08-03)<br />
* Frodi Jones (Stephen Harrison, 2015-08-03)<br />
* Matt Wayland (Stephen Harrison, 2015-08-03)<br />
* Marco Aite (Stephen Harrison, 2015-08-03)<br />
* Graeham Douglas (Stephen Harrison, 2015-08-03)<br />
* Robin Sterling (Stephen Harrison, 2015-08-07)<br />
* Abhi Manyu (Stephen Harrison, 2015-08-07)<br />
* Ward Hills (Stephen Harrison, 2015-08-07)<br />
* Carols A. Lugo (Stephen Harrison, 2015-08-07)<br />
* Ben Alper (Stephen Harrison, 2015-08-07)<br />
* Jon Green (Stephen Harrison, 2015-08-07)<br />
* Marcin Izo (Stephen Harrison, 2015-08-07)<br />
* Steve Upton (Rob Voisey, 2015-08-11)<br />
* Frederic Sorgeloos (Rob Voisey, 2015-08-11)<br />
* Andrew Cooke (Rob Voisey, 2015-08-11)<br />
* Ned Booker (Rob Voisey, 2015-08-11)<br />
* Daryl Stewart (Paul Edgington, 2015-08-24)<br />
* Nacho Lopez (Paul Edgington, 2015-08-24)<br />
* Ed Robertson (Paul Edgington, 2015-08-24)<br />
* Clive Beale (Paul Edgington, 2015-08-24)<br />
* Oliver Fleck (Paul Edgington, 2015-08-24)<br />
* Mark Cheverton (Rob Voisey, 2015-09-08)<br />
* Nik (Rob Voisey, 2015-09-08)<br />
* Dan Tidhar (Rob Voisey, 2015-09-08)<br />
* Tobias Wenzel (Rob Voisey, 2015-09-08)<br />
* Brian Starkey (Rob Voisey, 2015-09-08)<br />
* Jonathan Waite (Rob Voisey, 2015-09-08)<br />
* Emyr James (Rob Voisey, 2015-09-08)<br />
* Richard Hall (Rob Voisey, 2015-09-08)<br />
* Andrew Dunn (Rob Voisey, 2015-09-08)<br />
* Andrea Cipri (Paul Edgington, 2015-09-30)<br />
* John Sidinopoulos (Paul Edgington, 2015-09-30)<br />
* Stuart Barton (Paul Edgington, 2015-09-30)<br />
* Mark Calleta (Paul Edgington, 2015-09-30)<br />
* Martin Lenz (Paul Edgington, 2015-09-30)<br />
* Phill Banks (Paul Edgington, 2015-10-21)<br />
* Felix Morley (Paul Edgington, 2015-10-21)<br />
* David Jordan (Paul Edgington, 2015-10-21)<br />
* Mark Roberts (Stephen Harrison, 2015-10-23)<br />
* Jenny Molloy (Stephen Harrison, 2015-10-23)<br />
* Henry Cawley (Rob Voisey, 2015-11-18)<br />
* Bogdan Spiridom (Rob Voisey, 2015-11-18)<br />
* Jakub Sanak (Rob Voisey, 2015-11-18)<br />
* Jack Brewster (Rob Voisey, 2015-11-18)<br />
* Mayke Santos (Rob Voisey, 2015-11-18)<br />
* Luis Veiga Pumar (Stephen Harrison, 2015-11-24)<br />
* Greg Matthews (Stephen Harrison, 2015-11-24)<br />
* Brian Corteil (Stephen Harrison, 2015-11-24)<br />
* Rob Rescorla (Stephen Harrison, 2015-11-24)<br />
* Leo Rones (Stephen Harrison, 2015-11-24)<br />
* Diana Probst (Stephen Harrison, 2015-11-25)<br />
* Adrian van den Heever (Stephen Harrison, 2015-11-25)<br />
* Al Napp (Stephen Harrison, 2015-11-25)<br />
* Katy Marshall (Stephen Harrison, 2015-12-01)<br />
* Peter Mottram (Stephen Harrison, 2015-12-01)<br />
* David Barham (Stephen Harrison, 2015-12-01)<br />
* Johan Henriksson (Stephen Harrison, 2015-12-01)<br />
* Fotis Fotiadis (Stephen Harrison, 2015-12-01)<br />
* Oliver Martin (Stephen Harrison, 2015-12-01)<br />
* Andrew Drummond (Stephen Harrison, 2015-12-01)<br />
* Spencer Dixon (Stephen Harrison, 2015-12-01)<br />
* Jonathan Woolf (Rob Voisey, 2016-01-07)<br />
* Daniel Bailey (Rob Voisey, 2016-01-07)<br />
* David Haines (Rob Voisey, 2016-01-07)<br />
* Giovanni Bisutii (Rob Voisey, 2016-01-07)</div>Danieljabaileyhttp://wiki.makespace.org/File:TrainingCheatsheetUM2.pdfFile:TrainingCheatsheetUM2.pdf2016-02-09T20:07:33Z<p>Danieljabailey: Cheat sheet for training on the UM2 in PDF form, generated from the wiki text for a single side of A4 on (9th of Feb 2016)</p>
<hr />
<div>Cheat sheet for training on the UM2 in PDF form, generated from the wiki text for a single side of A4 on (9th of Feb 2016)</div>Danieljabaileyhttp://wiki.makespace.org/Equipment/3D_Printer/UM2TrainingEquipment/3D Printer/UM2Training2016-02-09T20:03:51Z<p>Danieljabailey: /* Trained Users */ Just fixing the spelling on my name</p>
<hr />
<div>[[Equipment|Equipment]] / [[Equipment/3D Printer|UM2]] / Training<br />
<br />
= Ultimaker 2 3D Printer Training =<br />
<br />
This page documents the process for being trained on the Ultimaker 2 Printer, and the list of members who have completed that training.<br />
<br />
== Summary ==<br />
<br />
Training takes place in three main steps:<br />
* Group Training of 1-4 members, going through the equipment and how to use it (~1hr)<br />
* Individual Training Task, where an individual member is set a task to complete to prove and improve understanding (~20min each)<br />
* Recommended project oversight, where more experienced users oversee the projects being undertaken when cutting (first 2-3 projects)<br />
<br />
A shorter conversion training session is available for members who were previously signed off to use the Makerbot 2X printer. These sessions last around 20 minutes and do not include individual sessions.<br />
<br />
== Booking ==<br />
<br />
For discussing and arranging slots, please use the mailing list. New training sessions will be announced on the Meetup group.<br />
<br />
Notes:<br />
* You can only be trained if you have RSVP'd to a Meetup session<br />
<br />
== Training Cheatsheet - Conversion Course ==<br />
<br />
Members already trained on and familiar with the Makerbot 2X can attend this short conversion course to be signed off to use the Ultimaker 2 3D printer. Up to 10 people can be accommodated on each course, which lasts 20 to 30 minutes.<br />
<br />
1. Physical Differences from the 2X<br />
* Glass build plate, no kapton tape<br />
* Single extruder<br />
* Push feed<br />
<br />
2. General<br />
* Use the correct filament (2.85mm, NOT 3mm or 1.75mm)<br />
* New filament storage system<br />
<br />
3. Printing<br />
* Fence / Brim / Raft<br />
* OK to leave printer unattended after the first few layers<br />
* Camera available for remote monitoring<br />
* Use only plastic implements for part removal, take care not to melt them on the hot end<br />
<br />
4. Cura Software<br />
* Import and place<br />
* Simple mode<br />
* Brief overview of advanced mode<br />
* Temperature set on printer not slicer<br />
* Exporting to SD card<br />
<br />
5. Unload / Load filament<br />
* How to feed (slow first, then fast)<br />
* Select correct material in menu<br />
* Changing temperature and speed parameters from printer<br />
* Demonstrate the atomic method of cleaning the extruder to prevent feed jams<br />
<br />
6. Filament pricing<br />
* 5p per gram for PLA and ABS, to be kept under review<br />
* Include wastage!<br />
<br />
== Training Cheatsheet - Full Course ==<br />
<br />
'''Group Session'''<br />
<br />
1. Ask what each member hopes to get out of the 3D printer.<br />
<br />
2. Explain how 3D printing works<br />
<br />
3. Safety<br />
* Burn hazard – nozzle and build plate<br />
* Unit may move unexpectedly<br />
* Avoid prolonged exposure to ABS fumes<br />
<br />
4. Damage to machine<br />
* Fragile build plate<br />
* Jammed filament<br />
<br />
5. General<br />
* Use the correct filament (2.85mm)<br />
* Filament storage and feed system<br />
* Switch off when finished<br />
* Leave levelling to the owners but report any problems<br />
<br />
6. PLA vs ABS<br />
* How to tell the difference<br />
* Different temperature<br />
* PLA Biodegradable<br />
<br />
7. Software / workflow<br />
* Importing<br />
* Positioning on bed<br />
* Supports<br />
* Setting quality / speed trade off<br />
* Advanced options<br />
* Exporting to SD card<br />
<br />
8. Unload / load<br />
* Attaching spool or loading from storage box<br />
* Feeding (slow then fast)<br />
* Beware of wrapping round axle<br />
* Setting material in menu<br />
* Adjusting parameters, e.g. ABS plate temperature<br />
<br />
9. Printing<br />
* Preheating<br />
* Fence printing<br />
* Keep an eye on progress, locally or with camera<br />
* If leaving unattended, put a post-it with your contact details<br />
* Use only plastic implements for part removal<br />
<br />
10. Other stuff<br />
* Demonstrate atomic method of cleaning the nozzle to prevent feed jams<br />
* Strength characteristics – orientation is important<br />
* Paying<br />
<br />
'''Individual Training Task'''<br />
<br />
Task<br />
* Should demonstrate import, setup, position and run<br />
* Choose a part that takes about 10 mins to print (preloaded on PC)<br />
<br />
Steps<br />
* Set individual to work, don't prompt but do answer questions (or pose if needed)<br />
* Talk through design once done, question/check things etc<br />
* Proceed to printing (watch carefully all steps)<br />
<br />
Assuming all ok:<br />
* Get them to read the health and safety notes about operation and materials<br />
* Add to the trained member list<br />
<br />
'''Project Oversight'''<br />
<br />
For next 2-3 projects, recommend member will find another more experienced trained user to support them (second pair of eyes)<br />
<br />
== Trained Users ==<br />
<br />
The following members of Makespace are trained and qualified to use the 3D Printer (note, they are not qualified to train others however):<br />
<br />
* Paul Osborn (Rob Voisey, 2015-07-30)<br />
* Julius Schmidt (Rob Voisey, 2015-07-30)<br />
* Peter Knight (Rob Voisey, 2015-07-30)<br />
* Adam Mulligan (Rob Voisey, 2015-07-30)<br />
* Charlotte Harvey (Rob Voisey, 2015-07-30)<br />
* Alex Gee (Rob Voisey, 2015-07-30)<br />
* Albert Santos (Rob Voisey, 2015-07-30)<br />
* Zizwani Mhango (Rob Voisey, 2015-07-30)<br />
* Christie Nel (Rob Voisey, 2015-07-30)<br />
* Robert Karpinski (Rob Voisey, 2015-07-30)<br />
* Alexis Mather (Stephen Harrison, 2015-08-03)<br />
* Ben Wheatley (Stephen Harrison, 2015-08-03)<br />
* Stevan Wing (Stephen Harrison, 2015-08-03)<br />
* Jae Tumer (Stephen Harrison, 2015-08-03)<br />
* Jennifer Herbert (Stephen Harrison, 2015-08-03)<br />
* Frodi Jones (Stephen Harrison, 2015-08-03)<br />
* Matt Wayland (Stephen Harrison, 2015-08-03)<br />
* Marco Aite (Stephen Harrison, 2015-08-03)<br />
* Graeham Douglas (Stephen Harrison, 2015-08-03)<br />
* Robin Sterling (Stephen Harrison, 2015-08-07)<br />
* Abhi Manyu (Stephen Harrison, 2015-08-07)<br />
* Ward Hills (Stephen Harrison, 2015-08-07)<br />
* Carols A. Lugo (Stephen Harrison, 2015-08-07)<br />
* Ben Alper (Stephen Harrison, 2015-08-07)<br />
* Jon Green (Stephen Harrison, 2015-08-07)<br />
* Marcin Izo (Stephen Harrison, 2015-08-07)<br />
* Steve Upton (Rob Voisey, 2015-08-11)<br />
* Frederic Sorgeloos (Rob Voisey, 2015-08-11)<br />
* Andrew Cooke (Rob Voisey, 2015-08-11)<br />
* Ned Booker (Rob Voisey, 2015-08-11)<br />
* Daryl Stewart (Paul Edgington, 2015-08-24)<br />
* Nacho Lopez (Paul Edgington, 2015-08-24)<br />
* Ed Robertson (Paul Edgington, 2015-08-24)<br />
* Clive Beale (Paul Edgington, 2015-08-24)<br />
* Oliver Fleck (Paul Edgington, 2015-08-24)<br />
* Mark Cheverton (Rob Voisey, 2015-09-08)<br />
* Nik (Rob Voisey, 2015-09-08)<br />
* Dan Tidhar (Rob Voisey, 2015-09-08)<br />
* Tobias Wenzel (Rob Voisey, 2015-09-08)<br />
* Brian Starkey (Rob Voisey, 2015-09-08)<br />
* Jonathan Waite (Rob Voisey, 2015-09-08)<br />
* Emyr James (Rob Voisey, 2015-09-08)<br />
* Richard Hall (Rob Voisey, 2015-09-08)<br />
* Andrew Dunn (Rob Voisey, 2015-09-08)<br />
* Andrea Cipri (Paul Edgington, 2015-09-30)<br />
* John Sidinopoulos (Paul Edgington, 2015-09-30)<br />
* Stuart Barton (Paul Edgington, 2015-09-30)<br />
* Mark Calleta (Paul Edgington, 2015-09-30)<br />
* Martin Lenz (Paul Edgington, 2015-09-30)<br />
* Phill Banks (Paul Edgington, 2015-10-21)<br />
* Felix Morley (Paul Edgington, 2015-10-21)<br />
* David Jordan (Paul Edgington, 2015-10-21)<br />
* Mark Roberts (Stephen Harrison, 2015-10-23)<br />
* Jenny Molloy (Stephen Harrison, 2015-10-23)<br />
* Henry Cawley (Rob Voisey, 2015-11-18)<br />
* Bogdan Spiridom (Rob Voisey, 2015-11-18)<br />
* Jakub Sanak (Rob Voisey, 2015-11-18)<br />
* Jack Brewster (Rob Voisey, 2015-11-18)<br />
* Mayke Santos (Rob Voisey, 2015-11-18)<br />
* Luis Veiga Pumar (Stephen Harrison, 2015-11-24)<br />
* Greg Matthews (Stephen Harrison, 2015-11-24)<br />
* Brian Corteil (Stephen Harrison, 2015-11-24)<br />
* Rob Rescorla (Stephen Harrison, 2015-11-24)<br />
* Leo Rones (Stephen Harrison, 2015-11-24)<br />
* Diana Probst (Stephen Harrison, 2015-11-25)<br />
* Adrian van den Heever (Stephen Harrison, 2015-11-25)<br />
* Al Napp (Stephen Harrison, 2015-11-25)<br />
* Katy Marshall (Stephen Harrison, 2015-12-01)<br />
* Peter Mottram (Stephen Harrison, 2015-12-01)<br />
* David Barham (Stephen Harrison, 2015-12-01)<br />
* Johan Henriksson (Stephen Harrison, 2015-12-01)<br />
* Fotis Fotiadis (Stephen Harrison, 2015-12-01)<br />
* Oliver Martin (Stephen Harrison, 2015-12-01)<br />
* Andrew Drummond (Stephen Harrison, 2015-12-01)<br />
* Spencer Dixon (Stephen Harrison, 2015-12-01)<br />
* Jonathan Woolf (Rob Voisey, 2016-01-07)<br />
* Daniel Bailey (Rob Voisey, 2016-01-07)<br />
* David Haines (Rob Voisey, 2016-01-07)<br />
* Giovanni Bisutii (Rob Voisey, 2016-01-07)</div>Danieljabaileyhttp://wiki.makespace.org/Equipment/Laser_CutterEquipment/Laser Cutter2015-09-13T14:22:33Z<p>Danieljabailey: Added section "Fixing up a job that went wrong"</p>
<hr />
<div><br />
{{RedTool}}<br />
<br />
[[Equipment|Equipment]] / Laser Cutter<br />
<br />
[[File:Makespace-laser-cutter.JPG|thumb|460px|right|Our LS6090 PRO Laser Cutter]]<br />
<br />
= Summary =<br />
<br />
We have two LS 6090 PRO Laser Cutters. Each has a working area of 900mm by 600mm, and is powered by a 60w CO2 Water Cooled Laser Tube that can engrave and cut through materials such as wood, plastic, card, leather, fabrics, up to about 10-15mm thick (note, it can not cut metal). The laser cut is approximately 0.15mm wide, and a job can take a few seconds through to tens of minutes depending on material thickness and design complexity. <br />
<br />
We have dedicated PCs running LaserCut 5.3 software to import, prepare and download jobs to the Laser Cutter. It can import various formats, with DXF being the most commonly used, so various software packages can be used to create your designs.<br />
<br />
Here are some examples of laser jobs we've run (please add a photo of yours any time you do a job!)<br />
<br />
<gallery><br />
File:Laser-cut-focus-tool.JPG<br />
File:Laser-cut-front-panels.JPG<br />
File:Laser-cut-lizards.JPG<br />
File:Laser-cut-m-and-s.JPG<br />
File:Laser-cut-model-building.JPG<br />
File:Laser-cut-ply-m.JPG<br />
File:Laser_output_-_makespace_arrow.JPG<br />
File:Laser_box.jpg<br />
File:Croc-small.jpg<br />
File:LaserCutter_Jobs_1.jpg<br />
File:LaserCutterGallery_20130328.jpg<br />
File:LasercutSettlers.jpg<br />
File:Wolfstock1.jpg<br />
File:Mug-holder.jpg<br />
File:2013-10-21 20.10.06.jpg<br />
File:Indy jigster.png<br />
</gallery><br />
<br />
= Using the Laser Cutter =<br />
<br />
The laser cutter is a great way to easily produce accurate and complex 2D forms in various materials, and can be designed for with limited experience in various drawing or CAD applications. At the same time, it is an expensive tool with real risk of injury and fire, so is very important you know how to use it to avoid damaging yourself and the machine. '''You must only use the laser cutter if you have been trained, and if you are ever in any doubt about something, please ask for assistance.'''<br />
<br />
== Owners ==<br />
<br />
The Owners are those who have volunteered to be in charge of the laser cutter, organising maintenance, responding to technical issues and generally being a point of contact. The current Owners of the Laser Cutter are:<br />
<br />
* [[User:Mat-C|Mat Cook]]<br />
* [[User:DianaProbst|Diana Probst]]<br />
* [[User:stevancw|Stevan Wing]]<br />
* Owners who are a little less current, but may still be able to help:<br />
** [[User:Simon|Simon Ford]]<br />
** [[User:Barhamd|David Barham]]<br />
** [[User:Nickcadsoftuk|Nick Johnson]]<br />
** [[User:Tmonca|Toby Moncaster]]<br />
<br />
== Trainers ==<br />
<br />
The Trainers are those who have volunteered to teach others to use the laser cutter and to promote good working practice. The current Trainers for the Laser Cutter are:<br />
<br />
* Brian Starkey<br />
* [[User:stevancw|Stevan Wing]]<br />
* [[User:Mat-C|Mat Cook]]<br />
* [[User:robv|Rob Voisey]]<br />
<br />
* Currently slightly less frequent trainers are:<br />
** Martin de Selincourt<br />
** [[User:Simon|Simon Ford]]<br />
** [[User:Barhamd|David Barham]]<br />
** [[User:Nickcadsoftuk|Nick Johnson]]<br />
** [[User:Tmonca|Toby Moncaster]]<br />
<br />
<br />
If you have any questions, problems or concerns around the laser cutter, please use the forum page:<br />
* [http://makespace.org/forum/viewtopic.php?f=19&t=45 Laser Cutter Log]<br />
<br />
For the old mailing list thread see here:<br />
* [https://groups.google.com/d/topic/cammakespace/Tmce2iKVzD8/discussion Log : Laser Cutter]<br />
<br />
== Training ==<br />
<br />
<div style="background:#FADADD; border:1px solid #FFC0CB; padding:5px"><br />
<b>YOU CAN ONLY USE THE LASER CUTTER IF YOU HAVE BEEN TRAINED</b><br><br />
and have been added to the [[Equipment/Laser_Cutter/Training#Trained_Users|Trained Users]] list by one of the Owners<br />
</div><br />
<br />
To get trained on the laser cutter and be added to the qualified user list, you will need to arrange for a training session with one of the Laser Cutter Owners. <br />
<br />
If you'd like to arrange training, please see:<br />
* [[Equipment/Laser_Cutter/Training|Laser Cutter Training]]<br />
<br />
== Health and Safety ==<br />
<br />
The laser cutter is a potentially dangerous piece of equipment which must only be operated by members who have received appropriate training and who take due care. The top things to always remember when using the laser cutter are:<br />
* '''ONLY USE THE LASER CUTTER IF YOU ARE ON THE LIST OF TRAINED USERS'''<br />
* '''NEVER LEAVE THE LASER CUTTER RUNNING UNATTENDED'''<br />
* '''KNOW WHAT TO DO IF A FIRE BREAKS OUT'''<br />
* '''NEVER CUT MATERIALS THAT YOU DON'T KNOW ARE SAFE'''<br />
<br />
As a trained user, you should be very aware of the following risks and how to deal with them:<br />
<br />
'''FIRE (under normal operation)''' - Cutting at the wrong speed or the wrong power can result in the material igniting<br />
* You must watch the cutter at all times and be prepared to abort the job if problems occur<br />
* Small flashes of flame that don't hang around for a fraction of a second are acceptable, but any more is rare and not acceptable<br />
* If a fire does take, this is the process you should follow (from minor to major):<br />
** Press "pause" (the same button you started the job with) - This will turn the laser off so no more heat enters, and assuming the flame goes out, you can press "start" for the job to continue where it left off<br />
** Open the lid - With the job paused, you can open the lid to blow out the flame. Again, it is possible to re-close the lid and continue where you left off<br />
** Move the material from under the laser head assuming safe to do so (so it doesn't damage the optics; alternatively send the laser to home/datum), and smother with a spare sheet of material or blow out<br />
** Use the workshop CO2 extinguisher to extinguish the flame<br />
* You should also make a note in the log if any of this happens with associated materials and settings so we can keep track of any particular materials/settings we should look at <br />
<br />
'''FIRE (abnormal operation)''' - If the head gets stuck or something else goes wrong, ignition could happen much more suddenly or intensely<br />
* You must watch the cutter at all times and be prepared to abort the job if problems occur<br />
* If the head gets trapped (e.g. tomb-stoning of a piece, mechanical failure) or any other problem occurs that causes or could cause fire, this is the process you should follow:<br />
** Hit the emergency stop<br />
** Open the lid and move the material from under the laser head assuming safe to do so (so it doesn't damage the optics)<br />
** Blow out, smother with a spare sheet of material, or use the CO2 extinguisher to extinguish the flame as appropriate<br />
* Ensure a Maintainer looks at the machine before it is brought back in to action if it is not obvious what went wrong and all is ok<br />
* You should also make a note in the log if any of this happens with associated materials and settings so we can keep track of any particular materials/settings we should look at <br />
<br />
'''FUMES''' - The laser cutting process will release different smoke and fumes depending on the material.<br />
* Never cut PVC or a material you are not sure is safe. When PVC is heated it releases chlorine gas, this mixes with the moisture in the air and the result is hydrochloric acid which is toxic to humans and corrosive to machines. <br />
* Ensure the filter is on and the cutter lid stays closed for a while after a job to allow the fumes to clear. <br />
* If you are feeling strange, think the fume build up is too much, or for any other reason you are unsure, stop the job.<br />
<br />
'''TRAPPING''' - The head and bed of the cutter can be moved by the front panel menu or programs in the machines memory. <br />
* Be careful when working inside the cutting area or with the lid open not to trap hands, hair, clothing or anything else. <br />
* Always check the machine for unexpected items that may have fallen in before closing the lid. <br />
* Do not attempt to climb into the machine!<br />
<br />
'''LASER BURNS/LIGHT''' - A 60W laser can do real damage. <br />
* The laser should be safe within the confines of the machine, and cut-off automatically when the lid is open (although this should not be relied upon). The top window is safe to look through during a job, but do not attempt to interfere with these windows or the laser or in any way invent some way to look at the laser.<br />
* Do not tamper with the laser cutter, or any interlocks. All side panels of the laser should always be closed and locked whilst the machine is plugged in. <br />
* Do not put metal in the laser cutter.<br />
<br />
== Can I cut it? ==<br />
<br />
*Woody things<br />
** Wood: yes! (be careful of fire)<br />
** Plywood: yes if it is "laser ply". Normal plywood has non-laser compatible glue<br />
** MDF: no. Clogs up our filters and smells bad.<br />
** LaserMDF: no. It produces perhaps 50% the gunk of MDF but still too much.<br />
** Cork: yes. Let us know how it goes!<br />
<br />
*Plasticy things<br />
** Acrylic / Perspex: yes!<br />
** PVC/Vinyl: absolutely not. Produces chlorine.<br />
** Silicone: we tried it with very limited success. A mm or two perhaps, anything else chars and doesn't cut.<br />
** White Delrin/Acetal: yes with great care. Make sure filters running well. Don't open lid too quickly. Check for fumes and fire.<br />
** Black Delrin/Acetal: no. contains carbon black which can be toxic.<br />
** Teflon: no (it is toxic)<br />
** Nylon: no (consult an owner)<br />
** Polythene/polyethylene: no (consult an owner)<br />
** Lexan/Polycarbonate: no (consult an owner)<br />
** Polypropylene: yes just. You must clean the bed. It will cut up to about 2mm. It's not a great quality cut, but just about doable. Fire risk.<br />
** GPPS / Polystyrene / HIPS in thin solid sheet form: maybe. ask owner to help. NO FOAM (it's highly flammable)<br />
<br />
*Papery things<br />
** Card/Paper: yes! (be careful of fire)<br />
** Tissue: yes if super super really careful (be REALLY careful of fire, have emergency procedure in place before you start)<br />
<br />
*Metally things<br />
** Metal of any thickness doesn't cut. The surface can be engraved with a paint application. LMM6000 Surmark/Thermark has been tested and is suggested for use, but expensive. The owners suggest a speed of 800 and maximum power.<br />
<br />
*Exotics<br />
** Fibre glass: no (unknown resin, glass particles)<br />
** Carbon Fibre: no<br />
** Slate: engravable for good effect<br />
<br />
Good list of info here: http://inventionstudio.gatech.edu/wiki/Laser_cutter<br />
<br />
== Instructions ==<br />
<br />
To use the laser cutter, you must have been trained and have had your name added to the trained user list; these instructions are not a substitute for this training. See the training section to understand how you can become qualified to use the laser cutter.<br />
<br />
Although not a requirement, it is recommended someone else trained is also present when using the laser cutter. Having two pairs of eyes helps avoid forgotten steps, allows for double checking, clarifications and discussions, and ensures a greater pool of experience is both present and being built up as the laser is used.<br />
<br />
'''Power Up'''<br />
<br />
Give the machine a quick visual check. Make sure that there is nothing left on the bed, the water reservoir of the chiller looks normal, and that the equipment has no obvious damage or signs of being out-of-action. If the bed looks like it has residue on it, give it a wipe with IPA and a cloth. <br />
<br />
Turn on primary switch on the trunking marked 'Laser'. The air filter system to the right of the laser cutter should start as should the air pump and the chiller. It should power up, make a decent amount of noise, and the lights should indicate the filter is in good condition (i.e. no need for replacement).<br />
<br />
Make sure the lid is closed. Turn on the laser using the key on the right hand side. The inspection lamp should come on, a satisfying hum start up, and the cutter go into doing its self-checks.<br />
<br />
Before doing any job, the laser should be left to warm up for 4-5 mins. While the machine warms up, power on the adjacent PC and start the LaserCut application from the desktop. During this time the water temperature shown on the chiller should drop from ambient temperature to the usual setting of 18C.<br />
<br />
'''Load your Design'''<br />
<br />
The PC software has an import facility which seems to be happy taking AutoCAD 2004 DXF files and other formats. The workspace of the laser bed is represented as the workarea in the LaserCut software. If the import doesn't do what you want size-wise, you can select the whole image and then use the 'size' command from the drop down menu to set the dimension you want. Clicking on the three dots ... symbol will adjust the other axis in the same proportion (keeping the aspect ratio fixed). Selecting the 'centre on bed' option will locate your imported drawing on the centre of the machine's cutting bed.<br />
<br />
'''Assign Settings to Colours'''<br />
<br />
Each part of your drawing that is assigned a different colour can have a different cut action assigned. Each colour will appear on the menu on the right hand side of the screen with numbers related to power and speed of the laser which will be used for the colour. <br />
<br />
The main options are to Cut (line) or Engrave (raster fill). A marking on the material is a Cut. For each material and cutting depth required, a corresponding speed and power must be entered. The handbook provided with the machine gives suggested values for various materials but these should be considered as a starting point for a test. See the '''Power and Speed Settings''' section for our guidelines and experiences for these settings.<br />
<br />
'''Download to the Cutter'''<br />
<br />
Your drawing will feature a blue dot which represents the starting point of the laser; this is by default on the top right corner. In general, you will want to use "immediate" mode, which means this point represents wherever the laser is positioned when you start the job. You can also run the job in absolute mode by unchecking the box, making the job use absolute positioning on the workspace. <br />
<br />
To download, select Download and Download Current; the download option will by default call the file on the laser cutter 'LASER'.<br />
<br />
'''Set the Focus'''<br />
<br />
Before each job, the focus needs to be checked and set by adjusting the height of the bed, and thus the work piece, from the lens. The critical dimension here is 41mm and several gauges made of perspex will be left around the machine. This gauge needs to be a fit between the top surface of the material you intend to cut and the white plastic 'flap' on the lens piece. The height of the table is adjusted using the UP and DOWN buttons. Failure to set the distance correctly will result in an out of focus laser and much bigger (but lower powered) cut line. Always ensure there is clearance between the material and laser head before the head moves. <br />
<br />
'''Aligning and Testing the Job'''<br />
<br />
The cutter's menu will show the most recent downloaded file highlighted. Pressing the 'test' button will make the head travel along the square maximum extends of the cuts. This shows you that you have the material in the right place, and you have enough of it! You can do this repeatedly, moving the work piece by hand or the laser head using the arrow keys (after hitting ESC), until you are confident you have things where you want them.<br />
<br />
'''Cut the Job'''<br />
<br />
When happy with the location of the material, close the lid and press 'start' to start the cutter. Watch the head and at least at first be prepared to press the 'stop' button immediately if you find you are burning massive holes in your work piece! This goes back to doing some tests on a sample of your material and making sure you are happy with the cut speeds and power you have selected. You should stay near the cutter at all times and be prepared to pause it or stop it in the event of fire. <br />
<br />
<span style="color:red">'''DO NOT EVER LEAVE THE CUTTER UNATTENDED'''</span><br />
<br />
'''Finishing'''<br />
<br />
The end of the job is signified by a beep. Waiting a few moments for the exhaust pump to clear any remaining smoke is a good idea, especially with wood, and will limit the build up of smells in the rest of the workshop. Remove your work piece, ensuring that all parts are cleared from the bed of the machine.<br />
<br />
'''Power Down'''<br />
<br />
The cutter is turned off using the key switch, then the air filtering system with the green rocker switch. Shut down the PC and double check that everything is left in a safe state for the next user. <br />
<br />
'''Clean the bed of debris using the soft brush, then wipe down the bed using IPA and a cloth.'''<br />
<br />
If you have been cutting particularly 'dirty' materials, most notable MDF and Ply which leave a sticky residue then you will need to use the course side of one of the oven pads and lots of 'elbow grease'. Residue on the bed can impact the next persons' job so please make the effort to clean up and leave the cutter as you would wish to find it.<br />
<br />
Go away excited by what you can make and come back with lots more drawings!<br />
<br />
== Power and Speed Settings ==<br />
<br />
In due time we will try to build up a large sample stock of materials and record the values which work best. Here are the sample material tests we have so far:<br />
<br />
<gallery><br />
File:Laser-schmoo-3mm-acrylic.JPG|3mm Acrylic<br />
File:Laser-schmoo-10mm-acrylic.JPG|10mm Acrylic<br />
File:Laser-schmoo-9mm-mdf.JPG|9mm MDF (note: do not cut MDF - see above!)<br />
</gallery><br />
<br />
Settings to get you started:<br />
*3mm Acrylic: Speed 12, Power 100, Corner power 100<br />
*5mm Acrylic: Speed 6, Power 100, Corner power 100<br />
*Acrylic shallow cut: Speed 30, power 50, corner power 50<br />
*Etching acrylic: Speed 400, Power 50, Spacing 0.05<br />
<br />
To make your own material test, a test grid can be downloaded here: [[Media:Test grid.zip]]<br />
<br />
== Tips & Tricks ==<br />
<br />
* If the laser cutter's user interface does not seem to respond/do what you want, hit "ESC" to return to 'normal mode'.<br />
* The opaque white acrylic needs slightly stronger settings for surface cuts as they are not as visible as in the transparent acrylic (i.e., for similar effect you need a deeper cut). Otherwise seems to cut equivalently to transparent acrylics.<br />
* If you want a tight fit of pieces or very accurate sizing, keep in mind that the laser beam has a width of just over 0.1 mm (maybe 0.11 or 0.12 mm). So all exterior cut lines should be offset by 0.05 mm; you can do this very easily in the LaserCutter Software with the "Offset" tool (units are in mm, so enter '0.05' and select 'Outer').<br />
* The DXF file format stores values only (not values and units). The internal units in the LaserCutter are in mm. If you set your document's units to mm in the exporting CAD system it should work fine, but generally it is a good idea to have a piece of geometry of known length, e.g. a line 100mm long, or a box of known size around your design. This makes adjusting the scaling a lot easier.<br />
* If you want to export a DXF from Inkscape (which is a great, free vector drawing package), then make sure you do "Object to path" from the Path menu for the whole object and then during the export stage, enable "use ROBO-Master type of spline output". This should make sure all the curves and so on work. NB: in some cases the "ROBO-Master" option actually makes curves not work, and it should be disabled; see this [https://wiki.nottinghack.org.uk/wiki/Laser_cutter/Inkscape Nottinghack page]<br />
* There's now a page to help with Inkscape and our laser at [[Equipment/Laser_Cutter_Inkscape]]<br />
* If the jog buttons (arrow keys moving the laser head around) are only moving the head in small single steps rather than moving it continuously, make sure that the jog step size is set to 0.0mm in the Jog Settings section of the menu.<br />
<br />
== Fixing up a job that went wrong ==<br />
<br />
If you messed up a job and, for example, some cut lines weren't cut, you might try to run the job again after deleting all of the lines except the ones that didn't cut. This will work if the origin is in the same place but, depending on the design, it might not be once you delete some lines. To solve this problem, you can run the job with the power set to 1 for all your fix-up lines. This is so low that it will not even mark the material but will show you exactly where the lines will go when you run it again with the correct power settings. You can then line this up correctly before doing your fix-up. Perhaps even set the speed a little lower so you can tell the difference between travel and cut movements.<br />
<br />
Alternatively, if you can, keep enough lines to ensure that the origin stays in the same place, then set these lines to power 1 if you don't need them.<br />
Then you can run the job again and everything will be in exactly the same place, no adjustment needed. Alternatively, you could avoid deleting any lines and just set the unwanted lines to power 1. If you have lots of lines however, this might make the cutter spend lots of time doing nothing.<br />
<br />
== Fixing strange issues ==<br />
<br />
* Etching doesn't work<br />
** Lines are not closed. LaserCut usually warns you about this. Ctrl-a to select all, then Tools->Unite Lines (0.001 should be fine).<br />
** Two copies on top of each other. Copies on top of each other "cancel out" any etching. Delete one copy.<br />
** Test with Menu->Laser->Simulate<br />
<br />
* LaserCut will not download to the laser cutter<br />
** Check laser cutter isn't in a paused state<br />
** Restart LaserCut on the PC. (We've not had any usb issues nor needed to restart the laser since upgrading the PC summer 2014).<br />
<br />
* Laser cuts things out 2+ times<br />
** Check you don't have two copies loaded on top of each other<br />
** Check it's not set to cut multiple times in LaserCut (this setting is right of the Cut/Engrave/Speed/Power settings)<br />
** Check the laser front panel says "001" at the bottom. If not, press right arrow until the number is highlighted, then down to adjust back to 1, then press return.<br />
<br />
* Laser will only cut at the top right of the bed<br />
** Download again with Immediate Mode ticked<br />
** On laser panel, press return (I think?) then right twice (should select the bottom left option), then press return (I think).<br />
<br />
*You Hit Emergency stop<br />
** E-M button needs twisting to re-activate<br />
** If that fails - check the circuit breaker inside. From the back of the machine, you want to open the lower flap on the left side, which should be unlocked. Near to the back, there is a breaker board. Flip the flippy bit.<br />
<br />
== Material Stock ==<br />
For the stock we hold, please see the [[Equipment/Laser_Cutter_Stock|Laser cutter stock]] page.<br />
<br />
= Maintenance =<br />
<br />
The maintenance of the Laser Cutter is carried out by the Owners, with some basic maintenance being carried out by Users on every job.<br />
<br />
== Maintenance Schedule ==<br />
<br />
Continuous Maintenance ('''Every job, done by all Laser Cutter Users''')<br />
* Clean the laser bed with IPA and cloth or Swarfega wipes<br />
* Clean any debris off laser bed and surround using soft brush<br />
<br />
Basic Maintenance (Every week, done by Laser Cutter Maintainers)<br />
* Clean the laser lens with IPA and cotton buds<br />
* Oil the 3 runners with 3-in-one light oil <br />
* Thoroughly clean the laser bed with IPA and cloth<br />
* Check the water level in the cooling tank<br />
* Clean and remove debris from the machine base and catchment drawer<br />
<br />
Full Maintenance (Every 4 weeks, done by Laser Cutter Maintainers)<br />
* Check the water is clean in the cooling tank (i.e. no contamination/organic build up)<br />
* Check filter unit for filter renewal<br />
* Oil the 4 rise and fall lead screws with 3-in-one light oil<br />
* Check mirrors and clean with a disposable sachet lens cleaner cloth (only if needed, mirror coatings are delicate)<br />
* Work through mirror alignment procedure to check alignment of mirrors<br />
<br />
== Maintenance Log ==<br />
<br />
For full log, see laser cutter wall sheet<br />
<br />
'''Reactive Maintenance'''<br />
* 15th Jan 2013, Simon Ford: Laser cutter not powering up, with switching on via key gives no activity whatsoever. No recollection of it cutting out during a job (Alexis), so assume it just stopped turning on at some point. Filter box and power sockets confirmed OK. Diagnosis: RCD in right back panel of Laser reset to off, no obvious reason why. Switching back on brought everything back to life OK.<br />
* 22nd, Simon Ford; 29th, Nicholas - same again.<br />
<br />
* Apr 2014, Mat Cook and Diana Probst: after previous changing of chiller water (Roger et al) the pump was complaining of lack of flow. Changed water and filtered, removed small blockage from rubber hose on laser tube.<br />
<br />
* 16 Apr 2014, Toby and Diana: changed laser tube, refilled chiller. Laser cutter fully working.<br />
<br />
* 25 Oct 2014, Mat and Diana mended lid spring brace. Cutter working fully.<br />
<br />
'''Regular Maintenance'''<br />
* Week Number, Date, Type, Owner (Notes)<br />
<br />
2013<br />
* January 7, Full, Chris @ HPCLaser'''<br />
* January 14, Basic, Simon Ford <br />
* January 21, Full, Simon Ford (running better than new :)'''<br />
* ...various maintenance events happened...<br />
* April 5th, Full, Simon Ford<br />
* July 1st, Full, David Barham (realigned mirrors)<br />
* July 15th, installed chiller<br />
<br />
2014<br />
* 16 Apr 2014, mirror alignment and optics checked after re-installation of tube. All fine. Toby and Diana.<br />
* 19 May 2014, mirrors cleaned, earthing wire on lid tightened. Diana (and Mat's screwdriver)<br />
* 21 May 2014, cleaned lens with Mat Cook. Diana<br />
* 02 Jun 2014, removed and cleaned laser bed<br />
* 14 Sep 2014, cleaned lens and mirrors, realigned. Diana and Brian Starkey<br />
<br />
* 30 Jun 2014 Fitted microswitches in series with the magnetic "lid closed" detector. <br />
* ??? 2014 "Jaws" Second laser cutter acquired<br />
* ??? 2014 Fitted microswitch to Jaws<br />
<br />
== Maintenance Shopping List ==<br />
<br />
* 3-in-one light oil <br />
* Cotton Buds<br />
* Lens cleaner sachets<br />
* Soft paint/cleaning brush<br />
* Thermometer for water tank<br />
* Hand held CO2 extinguisher<br />
<br />
= Further Information =<br />
<br />
* [http://hpclaser.co.uk/index.php?main_page=product_info&cPath=1&products_id=11 LS 6090 PRO Laser Product Page]<br />
* [http://hpclaser.co.uk/index.php?main_page=page&id=5&chapter=2 HPCLaser Technical Info]<br />
* [http://www.laserscript.co.uk/phpBB3/ Laserscript Forum]<br />
<br />
LaserCut 5.3<br />
* [http://www.leetro.com/english/sale/35.html Homepage]<br />
* [http://www.leetro.com/english/down/LaserCut5.3%20Manual%20V1.6.pdf Manual]<br />
<br />
== Installation ==<br />
<br />
<gallery><br />
File:Laser_-_van.JPG<br />
File:Makespace-laser-install-02.JPG<br />
File:Laser_-_building_2.JPG<br />
File:Laser_-_building.JPG<br />
</gallery><br />
<br />
== Purchase ==<br />
<br />
Full Purchase, Delivery and Installation (£6865.00+vat = £8238.00)<br />
* [http://hpclaser.co.uk/index.php?main_page=product_info&cPath=1&products_id=11 LS 6090 PRO Laser engraving and cutting machine, 600mm by 900mm 60W] (£5250.00+vat)<br />
* [http://hpclaser.co.uk/index.php?main_page=product_info&cPath=2&products_id=34 Laser Fume Filter] (£1250.00+vat)<br />
* Delivery (£190+vat)<br />
* Installation/Training (£175+vat)<br />
<br />
== Repairs ==<br />
<br />
We expect to have to change the following parts for general maintenance:<br />
* The laser tube (guess every 6-12 months)<br />
* The filter (guess every 3-6 months)<br />
* The optics (guess every 6-12 months)<br />
<br />
Maintenance and Spares:<br />
* [http://hpclaser.co.uk/index.php?main_page=product_info&cPath=2&products_id=3 60 watt C02 laser tube] (£275.00+vat)<br />
* [http://hpclaser.co.uk/index.php?main_page=product_info&cPath=2&products_id=12 50 mm Focus Meniscus Lens] (£75.00+vat)<br />
* Estimate for Call Out (£200.00)</div>Danieljabaileyhttp://wiki.makespace.org/Equipment/Laser_Cutter_InkscapeEquipment/Laser Cutter Inkscape2015-09-13T13:57:27Z<p>Danieljabailey: /* Exporting */ Added note about export setting</p>
<hr />
<div>=Inkscape tricks=<br />
<br />
A selection of hints to get the best out of Inkscape with our laser cutter. This applies to Inkscape 0.48.4.x and later, if you have an earlier version you should upgrade.<br />
<br />
<br />
==Page and grid setup==<br />
<br />
Set the default units (file->preferences) to mm. Then design everything in mm. These are preserved in dxf (choose mm as the units when saving) and you won't have to resize in the laser software.<br />
<br />
At the same point you can create a grid, I use a 1cm grid with 1mm minor lines - select the ''''Grids'''' tab and click ''''New'''' to create a new rectangular grid, for the one I use set units to mm, spacing to 1 and major grid line every 10. I change the colours so I can see the major grid lines even when zoomed in fully.<br />
<br />
Now save your document as "MyDefaultInkscapeDocument" and use it to start every project you work on :)<br />
<br />
This is a (zipped) default inkscape document (mm as default and 1mm/1cm grid) [[File:DefaultInkscape01.zip]]<br />
<br />
==Version 0.91==<br />
<br />
0.91 is latest and greatest. It very occasionally crashes (PC) compared to previous version (rock steady). Worth upgrading. Has newer image tracing options, but best of all, you can put formulae into its number boxes. So if your circle is as 0.543 mm and you want to move it right 1mm you can edit it to 0.543+1 mm and it sorts it all out for you. Also *2, /2, etc are handy for scaling.<br />
<br />
==Preferences==<br />
<br />
Find step and change it to something sensible like 0.5 mm. (Edit -> Preferences -> Behaviour -> Steps). Also change to inset/outset to 0.075 (ie half laser kerf). Now you have a 1mm grid and 0.5mm nudge increments. Shift-arrows give 5mm increments.<br />
<br />
==General hints==<br />
Use fill and don't use stroke (turn it off each time you create a shape). Stroke paths show the thick outline, and this confuses the sizing and bounding box for laser cut things. Fill mode for shapes makes everything work better. For shapes with holes, make it show self intersections as holes. This is closest to what a laser cutter will do. Menu: Object -> Fill and Stroke. Right hand side, click the "Fill" tab. Click the icon second from the right, looks a bit like a heart with a hole in it.<br />
<br />
==Grids==<br />
<br />
By default Inkscape won't actually use the grid, the buttons on the far right allow you to enable snap (first button from the top), to bounding boxes (second from top and subsequent four) and path nodes (the next group down). If you're not getting the snapping behaviour you expect play with turning these on. When snapping to path points it'll use the point closest to your mouse when you're dragging, so it matters where on the path you click!<br />
<br />
I find it easiest to get a sense of how big the piece is going to be if I set the page dimensions to those of the laser cutting bed, i.e. 900x600mm. You can do this from ''''File->Document Properties...'''' then entering a custom size, remember to change units to mm.<br />
<br />
==Outline mode==<br />
<br />
Inkscape can be put into outline mode, allowing you to see objects which have neither stroke nor fill. This is great because adding a stroke changes the dimensions of the object (slightly, but potentially enough to matter) and adding a fill makes it hard to see what you're doing. Select from ''''View->Display Mode->Outline''''. As an alternative a default fill with opacity of 10% works nicely when creating compound objects.<br />
Turning off stroke for each shape achieves the same result (make sure you give it a fill colour so you can still see it...)<br />
<br />
==Text on a path==<br />
<br />
Easy to do, create a path, create some text and use the ''''Text->Put on Path'''' menu item. With the text selected you can use the letter and word spacing controls to get the text to completely fill the path (I needed this for the plaque as we wanted the lists of names to butt up to each end of the shape). At this point the text and the path are coupled together, so while you can move the text away if you delete or change the path it'll alter. To get outlines ready for the cutter select the text object and do ''''Path->Object to Path'''', you can then delete the original path object used to flow the text.<br />
<br />
==Rounded rectangles==<br />
<br />
If you try to use these the cutter will largely ignore them. Use the ''''Path->Object to Path'''' to convert them into a generic path before exporting. Same for all boxes and circles.<br />
<br />
Alternatively, enable the "use ROBO-Master type of spline output" (an option during saving) if your version of Inkscape supports it.<br />
<br />
==Dashed paths==<br />
<br />
The laser won't pay any attention to stroke styles you set in Inkscape. Recent versions, however, include an extension under ''''Modify Path -> Convert to Dashes'''' which will render whatever stroke style you've selected.<br />
<br />
==Engraving text==<br />
<br />
Regular fonts used by Inkscape and everything else are outline fonts, that is to say they're defined as a filled shape. When used by the laser cutter the laser will cut the outline of the font, which looks great for large characters but often very badly (and slowly) for small typefaces. There's an extension at http://www.evilmadscientist.com/2011/hershey-text-an-inkscape-extension-for-engraving-fonts/ which allows for the use of engraving fonts where the font is defined in terms of the path used by the cutting tool rather than an outline.<br />
<br />
Note - the version of the library at that link is broken with modern (0.48.4) versions of Inkscape, I've fixed the problem and uploaded a patched version to https://dl.dropboxusercontent.com/u/70831580/HersheyText.zip<br />
<br />
==Exporting==<br />
<br />
In the latest version of inkscape you have an option from ''''File->Save As'''' to save as ''''Desktop Cutting Plotter (AutoCAD DXF R14)''''. With the default options this seems to work perfectly with the laser, dimensions are preserved etc. If you don't have this option upgrade your version of inkscape, it appeared some point over the last month or two.<br />
<br />
Note, 'default options' means export unit is set to mm.</div>Danieljabaileyhttp://wiki.makespace.org/File:Lexmark-c543.jpgFile:Lexmark-c543.jpg2015-07-21T20:35:10Z<p>Danieljabailey: A picture of one of the makespace printers.</p>
<hr />
<div>A picture of one of the makespace printers.</div>Danieljabailey