BitmapLaserEngraving - Revision history

Miguel at 13:43, 17 December 2017

2017-12-17T13:43:51Z

Miguel at 13:41, 17 December 2017

2017-12-17T13:41:21Z

Miguel: Created page with "Miguel Morin (this author) tried to reproduce the bitmap engraving on display at MakeSpace, which the creator no longer remembered. I used ImageMagick's convert function with ..."

2017-12-10T21:13:18Z

Created page with "Miguel Morin (this author) tried to reproduce the bitmap engraving on display at MakeSpace, which the creator no longer remembered. I used ImageMagick's convert function with ..."

New page

Miguel Morin (this author) tried to reproduce the bitmap engraving on display at MakeSpace, which the creator no longer remembered. I used ImageMagick's convert function with some settings.

First, I decided to use scan gap 0.05, or 20 pixels per mm, or 508 pixels per inch. That is the density. Then I divided the size of the piece I wanted to engrave by the density to obtain the size of the image in pixels. In my case, it was 1920x2560. I added "^" at the end so ImageMagick adjusts the size of the image to be higher than either of the dimensions, possibly adding a bleed:

convert /path/to/input/file -resize 1920x2560^ -density 5080 /path/to/output/file

The next command converts this resized image to a 1-bit bitmap, either black or white, i.e. either on or off:

convert /path/to/output/file/from/above -colors 2 +dither -type bilevel /path/to/final/output/file

This file is ready for LaserCut 5.3.

I tried both commands at once and LaserCut interpreted the output file as a grayscale and engraved only the darkest pixels. Doing it in two steps seemed to work.

I also tried half-toning the image and got different results, with more grain, but also a better overall resolution.

← Older revision		Revision as of 13:43, 17 December 2017
Line 14:		Line 14:

	I also tried half-toning the image and got different results, with more grain, but also a better overall resolution. The picture below shows the half-tone engraving on the left (made with Illustrator) and a dither engraving with the above details. Both pieces are stained with Tru-Oil 3 times. The staining compressed much of the contrast between black and white on the piece to the right.		I also tried half-toning the image and got different results, with more grain, but also a better overall resolution. The picture below shows the half-tone engraving on the left (made with Illustrator) and a dither engraving with the above details. Both pieces are stained with Tru-Oil 3 times. The staining compressed much of the contrast between black and white on the piece to the right.
−	[[File:~~Example~~.~~jpg~~]]	+	[[File:LaserBitmapEngraving.JPG]]

← Older revision		Revision as of 13:41, 17 December 2017
Line 13:		Line 13:
	I tried both commands at once and LaserCut interpreted the output file as a grayscale and engraved only the darkest pixels. Doing it in two steps seemed to work.		I tried both commands at once and LaserCut interpreted the output file as a grayscale and engraved only the darkest pixels. Doing it in two steps seemed to work.

−	I also tried half-toning the image and got different results, with more grain, but also a better overall resolution.	+	I also tried half-toning the image and got different results, with more grain, but also a better overall resolution. The picture below shows the half-tone engraving on the left (made with Illustrator) and a dither engraving with the above details. Both pieces are stained with Tru-Oil 3 times. The staining compressed much of the contrast between black and white on the piece to the right.
		+	[[File:Example.jpg]]