LaserCut53Notes (Laser Cutter Notes and FAQ) - Revision history

Miguel: format link properly

2018-07-08T16:00:46Z

format link properly

Miguel: Add cryptic error message with overlap data

2018-07-08T15:59:46Z

Add cryptic error message with overlap data

Miguel: Miguel moved page LaserCut53Notes to LaserCut53Notes (Laser Cutter Notes and FAQ): unable to find this page when searching for "laser cutter"

2018-07-08T15:57:07Z

Miguel moved page LaserCut53Notes to LaserCut53Notes (Laser Cutter Notes and FAQ): unable to find this page when searching for "laser cutter"

Miguel: Fix formatting

2018-07-01T19:37:59Z

Fix formatting

Miguel: Fix formatting

2018-07-01T19:37:09Z

Fix formatting

Miguel: Add problem and solution in changing engrave power

2018-07-01T19:36:45Z

Add problem and solution in changing engrave power

Mat-c: created

2014-08-11T18:30:54Z

created

New page

If it appears to talk to the laser, but "Download Current" does not work, it's because LaserCut cannot write to a couple of files in C:\ root. Temp workaround: run as admin. Full workaround: update permissions for these files.

← Older revision		Revision as of 16:00, 8 July 2018
Line 10:		Line 10:
	== "We have finded overlap data,please checd data and ouptu" ==		== "We have finded overlap data,please checd data and ouptu" ==

−	This means that some of your engraving paths overlap, and so the laser will turn on when it finds the outermost path and off when it finds an overlap. If you have the same shape twice, the laser will do the engraving passes without turning on and look like the laser is out of power. See also [~~this StackExchange thread](~~https://graphicdesign.stackexchange.com/questions/111461/laser-cutter-is-not-engraving-and-saying-we-have-finded-overlap-data/111462#111462).	+	This means that some of your engraving paths overlap, and so the laser will turn on when it finds the outermost path and off when it finds an overlap. If you have the same shape twice, the laser will do the engraving passes without turning on and look like the laser is out of power. See also [https://graphicdesign.stackexchange.com/questions/111461/laser-cutter-is-not-engraving-and-saying-we-have-finded-overlap-data/111462#111462 this StackExchange thread].

← Older revision		Revision as of 15:59, 8 July 2018
Line 7:		Line 7:

	If you can change the speed in engrave mode and every other setting in cut mode, but not the power in engrave mode (e.g., it's stuck at 15), then change both the power and the speed, which unlocks the setting of power.		If you can change the speed in engrave mode and every other setting in cut mode, but not the power in engrave mode (e.g., it's stuck at 15), then change both the power and the speed, which unlocks the setting of power.
		+
		+	== "We have finded overlap data,please checd data and ouptu" ==
		+
		+	This means that some of your engraving paths overlap, and so the laser will turn on when it finds the outermost path and off when it finds an overlap. If you have the same shape twice, the laser will do the engraving passes without turning on and look like the laser is out of power. See also [this StackExchange thread](https://graphicdesign.stackexchange.com/questions/111461/laser-cutter-is-not-engraving-and-saying-we-have-finded-overlap-data/111462#111462).

@@ Line 1: / Line 1: @@
-##Failure in "Download current"##
+== Failure in "Download current" ==
 If it appears to talk to the laser, but "Download Current" does not work, it's because LaserCut cannot write to a couple of files in C:\ root.  Temp workaround: run as admin.  Full workaround: update permissions for these files.
-##Unable to change power of Engrave##
+== Unable to change power of Engrave ==
 If you can change the speed in engrave mode and every other setting in cut mode, but not the power in engrave mode (e.g., it's stuck at 15), then change **both** the power and the speed, which unlocks the setting of power.

@@ Line 1: / Line 1: @@
-# Failure in "Download current" #
+##Failure in "Download current"##
 If it appears to talk to the laser, but "Download Current" does not work, it's because LaserCut cannot write to a couple of files in C:\ root.  Temp workaround: run as admin.  Full workaround: update permissions for these files.
-# Unable to change power of Engrave #
+##Unable to change power of Engrave##
 If you can change the speed in engrave mode and every other setting in cut mode, but not the power in engrave mode (e.g., it's stuck at 15), then change **both** the power and the speed, which unlocks the setting of power.

← Older revision		Revision as of 19:36, 1 July 2018
Line 1:		Line 1:
		+
		+	# Failure in "Download current" #

	If it appears to talk to the laser, but "Download Current" does not work, it's because LaserCut cannot write to a couple of files in C:\ root. Temp workaround: run as admin. Full workaround: update permissions for these files.		If it appears to talk to the laser, but "Download Current" does not work, it's because LaserCut cannot write to a couple of files in C:\ root. Temp workaround: run as admin. Full workaround: update permissions for these files.
		+
		+	# Unable to change power of Engrave #
		+
		+	If you can change the speed in engrave mode and every other setting in cut mode, but not the power in engrave mode (e.g., it's stuck at 15), then change both the power and the speed, which unlocks the setting of power.

← Older revision	Revision as of 15:57, 8 July 2018
(No difference)