PCB Milling on the Roland - Revision history

Perfectphase: /* Work Holding */

2013-07-17T00:28:59Z

‎Work Holding

Perfectphase: /* Work Holding */

2013-07-17T00:26:03Z

‎Work Holding

Perfectphase: /* Work Holding */

2013-07-17T00:25:53Z

‎Work Holding

Perfectphase: /* Boards */

2013-07-17T00:24:42Z

‎Boards

Perfectphase: /* Cutters */

2013-07-16T23:52:02Z

‎Cutters

Perfectphase: Created page with "This is an on-going log of the adventures of milling PCB's on the Roland. == Cutters == New carbide cutters in 45deg and 60deg, the drill is 1mm for scale. File:13071..."

2013-07-16T23:32:55Z

Created page with "This is an on-going log of the adventures of milling PCB's on the Roland. == Cutters == New carbide cutters in 45deg and 60deg, the drill is 1mm for scale. <gallery> File:13071..."

New page

This is an on-going log of the adventures of milling PCB's on the Roland.

== Cutters ==
New carbide cutters in 45deg and 60deg, the drill is 1mm for scale.

<gallery>
File:1307130032376161555.jpg
File:1307130022565580545.jpg
File:1307130015535156800.jpg
</gallery>

Turns out the 45deg cutters are a bit fragile and the tips break easily

<gallery>
File:13071700172215212796.jpg
File:13071700183915289969.jpg
</gallery>

This is the 60deg cutter after cutting 5 Ardunio sized PCB (top layer only), you can see the edge is starting to go on the tip (we only use at most 0.2mm of the cutter), but it's still producing good quality cuts.

<gallery>
File:13071700160615136621.jpg
</gallery>

← Older revision		Revision as of 00:28, 17 July 2013
Line 52:		Line 52:

	So tried clamping the board, but this still lead to warps in the board.		So tried clamping the board, but this still lead to warps in the board.
		+
		+	Hint: When zeroing the Z-axis, place the sensor in contact with the PCB and zero directly onto the PCB, then move to +15.00mm in Z and re-zero. This will remove any inaccuracy in the thickness of the sensor.

	'''Vacuum Clamping Project'''		'''Vacuum Clamping Project'''

← Older revision		Revision as of 00:26, 17 July 2013
Line 54:		Line 54:

	'''Vacuum Clamping Project'''		'''Vacuum Clamping Project'''
		+
	So at this point it seemed a vacuum bed would be a good idea.		So at this point it seemed a vacuum bed would be a good idea.

@@ Line 75: / Line 75: @@
 An attempt using the Henry Hoover, while providing enough vacuum, caused a worrying amount of heat.
-Next on the list of things to try will be the pump donated by Rachel, but am unsure if that will provide the required level of vacuum as it's really a blower not a vacuum source.
+Next on the list of things to try will be the pump donated by Rachel, but am unsure if that will provide the required level of vacuum as it's really a blower not a vacuum source.  An adapter needs to be manufactured first.
 If that fails then I'll look into sourcing a side channel pump, which are more suited to running for long periods in these conditions.

← Older revision		Revision as of 00:24, 17 July 2013
Line 41:		Line 41:
	File:13071700472717018164.jpg		File:13071700472717018164.jpg
	</gallery>		</gallery>
		+
		+	==Work Holding==
		+	The biggest issue so far has been holding the work flat. As the cut depth has to be 0.2mm or less, you need a good level surface to ensure a constant cut depth. Pro machines have pressure feet and floating heads, some even map the surface of the board prior to cutting and adjust cut depth accordingly. We have none of this so need to improvise.
		+
		+	First attempt, MDF machined flat. This is a no starter, no where near the tolerance required.
		+
		+	Next use a sheet of Model Board, this has good dimensional tolerance and is stable over time.
		+
		+	The next problem was the fact we were using double sided tape to hold down the PCB, that was no good, to much variation.
		+
		+	So tried clamping the board, but this still lead to warps in the board.
		+
		+	'''Vacuum Clamping Project'''
		+	So at this point it seemed a vacuum bed would be a good idea.
		+
		+	<gallery>
		+	File:WP_20130714_002.jpg
		+	File:WP_20130717_001.jpg
		+	File:WP_20130717_002.jpg
		+	File:WP_20130714_003.jpg
		+	</gallery>
		+
		+	This setup gives really good results and allowed a successful test pattern to be milled into an area 150x100mm with no partial cut through as had been seen before.
		+
		+	<gallery>
		+	File:13071701130718558003.jpg
		+	</gallery>
		+
		+	The problem is now that the system leaks, note the increase in taped edges in the above photos to minimise losses.
		+
		+	While this is to be expected, this causes problems for my 2 Stage Rotary Vane vacuum pump. That pump (which is normally used for degassing resin and resin infusion) does not like a partial vacuum, so the leaks above lead it to over heat, will radically shorten it's useful life.
		+
		+	An attempt using the Henry Hoover, while providing enough vacuum, caused a worrying amount of heat.
		+
		+	Next on the list of things to try will be the pump donated by Rachel, but am unsure if that will provide the required level of vacuum as it's really a blower not a vacuum source.
		+
		+	If that fails then I'll look into sourcing a side channel pump, which are more suited to running for long periods in these conditions.

@@ Line 2: / Line 2: @@
 == Cutters ==
-New carbide cutters in 45deg and 60deg, the drill is 1mm for scale.
+New carbide cutters in 45deg and 60deg, the drill is 1mm for scale.  The thickness of the tip is 0.1mm
 <gallery>
@@ Line 10: / Line 10: @@
 </gallery>
-Turns out the 45deg cutters are a bit fragile and the tips break easily
+Turns out the 45deg cutters are a bit fragile and the tips break easily.
 <gallery>
@@ Line 21: / Line 21: @@
 <gallery>
 File:13071700160615136621.jpg
 </gallery>