Difference between revisions of "Equipment/Electronics Workbenches"
From Makespace
| Line 23: | Line 23: | ||
* Thurlby Thandar TG212 0.1Hz-2MHz function generator (sine, square, sawtooth) | * Thurlby Thandar TG212 0.1Hz-2MHz function generator (sine, square, sawtooth) | ||
* Thurlby Thandar TF830 1.3GHz high resolution reciprocal measurement | * Thurlby Thandar TF830 1.3GHz high resolution reciprocal measurement | ||
| − | |||
| − | |||
| − | |||
| − | |||
== Shared equipment == | == Shared equipment == | ||
| − | |||
* Soldering irons: | * Soldering irons: | ||
** 2x Tenma AT60D soldering stations (up to 400C) | ** 2x Tenma AT60D soldering stations (up to 400C) | ||
| Line 41: | Line 36: | ||
=== Components and small tools === | === Components and small tools === | ||
| − | |||
* PCB holders or "helping hands" | * PCB holders or "helping hands" | ||
* Magnifying lamps | * Magnifying lamps | ||
| Line 50: | Line 44: | ||
== Notes == | == Notes == | ||
| − | |||
It would be nice if someone could dig out URLs for manuals for the above, if available, and link to them from their listing lines. | It would be nice if someone could dig out URLs for manuals for the above, if available, and link to them from their listing lines. | ||
| Line 69: | Line 62: | ||
* Spectrum Analyser | * Spectrum Analyser | ||
| + | <!-- | ||
== Archive== | == Archive== | ||
| + | |||
| + | <gallery> | ||
| + | File:1836058-40.jpg|[http://cpc.farnell.com/tenma/72-8700/power-supply-bench-2x-32v-5a/dp/IN06096 Dual 32V, 5A Bench Power Supply] | ||
| + | </gallery> | ||
| + | |||
Bench Requirements (based on conversations with lots of people!) | Bench Requirements (based on conversations with lots of people!) | ||
* Height: Standard workstation/stool height (~840mm) rather than desk/chair height - allows working standing or sitting on stools | * Height: Standard workstation/stool height (~840mm) rather than desk/chair height - allows working standing or sitting on stools | ||
| Line 83: | Line 82: | ||
** Some form of raised area for scopes/test equipment | ** Some form of raised area for scopes/test equipment | ||
** Very sturdy - i.e. wont move if lent on, pushed against etc | ** Very sturdy - i.e. wont move if lent on, pushed against etc | ||
| + | --> | ||
Revision as of 21:49, 23 February 2014
Equipment / Electronics Workbenches
Workbenches for electronics and precision work.
Contents
Enthusiast Bench
A 1800mm x 900mm ESD cantilever bench from here
Equipment
- Hameg HM-203s 20MHz analogue oscilloscope
- Black*Star Jupiter 500 0.1Hz-500kHz function generator (sine, square, sawtooth)
- Philips PM6622 80MHz counter
Expert Bench
A 1800mm x 900mm ESD cantilever bench from here
Equipment
- BlackJack BK6000 Rework station
- Philips PM 3217 50MHz analogue Oscilloscope
- Thurlby Thandar TG212 0.1Hz-2MHz function generator (sine, square, sawtooth)
- Thurlby Thandar TF830 1.3GHz high resolution reciprocal measurement
- Soldering irons:
- 2x Tenma AT60D soldering stations (up to 400C)
- Bench power supplies (e.g. a mix of 5V, 12V, variable, and multi-rail PSUs)
- Farnell AP20-80: up to 20V at up to 80A
- Hameg HM7042-3 dual: each channel up to 32V at up to 2A
- Tenma 72-8695 two channels each up to 32V at up to 3A, plus a single fixed 5V/2A channel
- Logic analyser:
- HP 16500A (status unknown: may not be operational but has probes pack)
- Currently assumed dead.
Components and small tools
- PCB holders or "helping hands"
- Magnifying lamps
- Side cutters
- Multimeters
- Wire
- Selection of basic components (res, caps, v-reg, basic digital logic, basic IC's - 555,358, connectors, cable)
Notes
It would be nice if someone could dig out URLs for manuals for the above, if available, and link to them from their listing lines.
Wishlist
Need
- Abrasive pen
- Heatsink tweezers
- Tweezers
- ESD handling equipment, eg. anti-static mats, wrist-strap, earth points, tester
Want
- Logic Analyser
- 100MHZ Digital Oscilloscope
Would Be Nice
- USB microscope with monitor
- Spectrum Analyser
