Revision as of 22:14, 7 April 2015

3D Printer Training

This page documents the process for being trained on the 3D Printer, and the list of members who have completed that training.

Summary

Training takes place in three main steps:

Group Training of 1-4 members, going through the equipment and how to use it (~1hr)
Individual Training Task, where an individual member is set a task to complete to prove and improve understanding (~30min each)
Project Oversight, where more experienced users oversee the projects being undertaken when cutting (first 2-3 projects)

Training on the 3D Printer is run by the 3D Printer Owners. The 3D Printer Owners are a group of people responsible for maintaining and training on the 3D Printer, and hence have been trained to train, and trained to perform the weekly and monthly maintenance on the 3D Printer.

Booking

This is no longer handled here on the wiki.

For discussing and arranging slots, please use the mailing list thread [1]. New training sessions will be announced on the Meetup group.

Notes:

You can only be trained if you have RSVP'd to a Meetup session

Trained Users

The following members of Makespace are trained and qualified to use the 3D Printer (note, they are not qualified to train others however):

Chris Abri
Rachel Rayns
Tom Ingham
Paul Osborn
Moin Ali
Andy Fisher
Edward Imhagwe
Yi Wei
Errol McMullen
Mark Watson
Catarina Violante
Maciek Piatek
Adrian van den Heever
Brian Corteil
Rod Williams
Peter Provis
Ben Evans
Roeland Schumacher
Archie Reid
Adrian Carr
Ward Hills
Paul Holland
Pop Sharma
Patrick Greaney
Kevin Latter
Martin de Selincourt
Alexis Mather
Andrew Dunn
Hannah Wray
Anne Harrison
Ben Alper
Ajith Shadakshari
Mark Mellors
Toby Moncaster
Alan Tennant
Jake Young
John Sturdy
David Bebb
Ben Wheatley
Diana Probst
Richard Mitchell (mandatory only)
Christie Nel (mandatory only)
Andrew Lipson (mandatory only)
Toby Roberts (mandatory only)
Dan Tidhar
Jennifer Herbert
Matthew Ireland
Harry Braviner
Saar Drimer
Robert Hoff
Daniel Garden
Armando Carlone
Marcin Izo
James Hutton (mandatory only)
Anthony Wainman (mandatory only)
Jia Wei Lim (mandatory only)
Julius Schmidt (mandatory only)
Hazel Jenkins (mandatory only)
Benjamin Kidder (mandatory only)
Joshua Keeler (mandatory only)
Simon Birrell (mandatory only)
John Simm (mandatory only)
Theo Sanderson (mandatory only)
Jon Aas (mandatory only)
Stephen Jeapes (mandatory only)
Anna Stoilova (mandatory only)
Jim Dilks (mandatory only)
Katia Dilks (mandatory only)
Aleksandar Tomic (mandatory only)
Gaye Saykok (mandatory only)
Fergus Riche (mandatory only)
David Barham (Mandatory only)
Marco Aita (Mandatory only)
Jason White (Mandatory only)
Brian Starkey (Mandatory only)
David Cox (Mandatory only)
Matt Grimes (Mandatory only)
Tim Regan (Mandatory only)
Stuart Wilson (Mandatory only)
Andy Spencer (Mandatory only)
Ester Leighton (Mandatory only)
Richard Fosh (Mandatory only)
Peter Knight
John Campbell
Arun Rao
Peter Mottram
Marcin Zaba
Jon Green
Dave Potts
Reid Potts
Mark Roberts
Piccardo Gheradi
Edward Imhagwe
Robert Hogg
Michal Stefanow
Charlie Stokes
Leo Impett
Patrick Wollner
Patrick Baigent
Kate Aston
Shelagh Shepherd
Damien Guihen
Paul Edgington
Wayne Keenan
Liza Read
David Horsnell
Emyr James
Francisco Cordobes Aguilar
Nicola Powys
Jia Wei Lim
Sonya Sireau
Andrew Gale
Andre Powell
Tom Myers
Hidde-Jan Lemstra
Mark Cheverton
Robert Karpinski
Alex Wortley
Jason Holloway
Alex Holloway
Mat Cook (1/5/2014)
Toby Norman (1/5/2014)
Toby Bunting (1/5/2014)
Rob Voisey (1/5/2014)
Joe Tapply (1/5/2014)
Carl Phillips (1/5/2014)
Alberto Santos (6/5/14)
Owen McAree (6/5/14)
Eric Jones (6/5/14)
Martin Hollis (8/5/14)
Mark Tillotson (8/5/14)
Neil Tan (8/5/14)
Mat Greenwood (8/5/14)
Alex Atkinson (15/5/14)
Al Napp (15/5/14)
Ian McFarlane (15/5/14)
Michael Dales (20/5/14)
Lihua Han (20/5/14)
Rick Lupton (20/5/14)
Stephen Woodhead (20/5/14)
Tim Rower (20/5/14)
Kristof Klos
Antony Quinn
Thomas Keller
Matthew Taylor
Shashank Srinivasan
Milosz Wasilewski
Tom Roberts
Alex Gee
Rob Yates
Joe Watson
Brandon Invergo
Marco Galardini
Owen Woods (09/07/2014)
David Taylor (25/07/2014)
Craig Richardson (25/07/2014)
Kevin Rathbone
Simon West
Guillaume Tucker
Zizwani Mhango
Joe Gribbom
Richard Armstrong
Rachel Bow
Will Hartley
Donatien Garnier
Graeham Douglas
Stevan Wing
John Sidiropoulos
Emilio Monti
Alba Diez
Rob Shore
Katy Marshall
Daniel Farrant
Jonathan Waite
Giovanni Orlando
John Clarke
Ben Week
Abhimanyu Singh
Gustavo de Rojas Foschtinski
Tariq Harris
Joe Turner
Clara Todd

7 April 2015

Juan "Jay" Cano
Jenny Molloy
Timothy Baldock
Robin Sterling
Henry Begg
Matt Wayland
Hugo Keene
Carlos A Lugo
Andrew Lipson
Adam Mulligan
Charlotte Harvey
Luke Twydell
Ed Robertson
Maria Isabella Gariboldi
Patrick H. Riggs
Jo Brook
(Andrew Holland - not yet inducted to Makespace)

UP Trained Users

Martin Lenz (Brian Starkey 12/3/15)
Alex Gee (Brian Starkey 12/3/15)
Harry Braviner (Brian Starkey 12/3/15)
Kim SJ (Brian Starkey 12/3/15)
Paul Edgington (Brian Starkey 12/3/15)

Delayed training blacklist:

Now on the wall in Makespace, near the 3D printers.

Training Cheatsheet

The training structure and prompt sheet. Please note, this is used by the 3D Printer Owners as a prompt to ensure training is executed in a consistent and complete fashion is included on this page; this does not constitute and is not a substitue for the training itself.

Group Training

The group training introduction structure, suitable for 1-5 members at a time in a 1 hr session.

3D Printing Induction syllabus:

how 3D printing works

safety

 burn hazard
   nozzle and platter
 unit may move unexpectedly
 avoid prolonged exposure to ABS fumes

damage to machine

 kapton
   is fragile - don't use scraper!
   is expensive
   needs to be clean
 don't leave the machine unattended
   heater could stick on if software crashes, for example

general

 SD card eccentricities
 keep lid on when printing
 switch off when finished

PLA vs ABS

 how to tell the difference
 different temperature
 biodegradable
 need to change temperature profiles!

unload/load,

 different axles for different spools
 spool from under reel
 beware of wrapping round axle!
 colours (no need to run out all because test strip does that)
 setting PLA/ABS
 cut off lump

printing

 preheating
 if model stuck, wait to cool
 keep an eye on it. can go strange half way!

levelling

 not often needed
 symptoms of unlevelness
   first layer too thin or varying thickness
   part not sticking
   worst case: head touching bed
 be careful not to damage kapton

software/workflow (it is proposed that the course should not include detailed introduction to the software, as this is mostly obvious, can freely be downloaded, and is well documented) - if there is high demand, consider running a software training course

 scaffolding
 setting colours

multicolour

 can't do scaffolding and multicolour - maybe not true anymore?
 issues with mixed materials

other stuff

 strength characteristics - orientation is important
 don't use fine
 don't leave the room
 paying

Individual Training Task

The individual task to get familiar, prompt questions and check understanding:

Task

Make something?
Should demonstrate import, setup, position and run
possible examples (around 10m printing time)
- plain_game_tokes 1/2/5
- SpaceShuttle-small
- CookieCutter_apple_small

Steps

Set individual to work, don't prompt but do answer questions (or pose if needed)
Talk through design once done, question/check things etc
Proceed to printing (watch carefully all steps)

Assuming all ok:

Get them to read the health and safety notes about operation and materials
Add to the trained member list!

Project Oversight

For next 2-3 projects, ensure member will find another more experienced trained user to support them (second pair of eyes)

@@ Line 210: / Line 210: @@
 * Joe Turner
 * Clara Todd
+April 2015
+* Juan "Jay" Cano
+* Jenny Molloy
+* Timothy Baldock
+* Robin Sterling
+* Henry Begg
+* Matt Wayland
+* Hugo Keene
+* Carlos A Lugo
+* Andrew Lipson
+* Adam Mulligan
+* Charlotte Harvey
+* Luke Twydell
+* Ed Robertson
+* Maria Isabella Gariboldi
+* Patrick H. Riggs
+* Jo Brook
+* (Andrew Holland - not yet inducted to Makespace)
 = UP Trained Users =

Difference between revisions of "Equipment/3D Printer/Training"

Revision as of 22:14, 7 April 2015

Contents

3D Printer Training

Summary

Booking

Trained Users

UP Trained Users

Training Cheatsheet

Group Training

Individual Training Task

Project Oversight

Navigation menu

Views

Personal tools

Navigation

Search

Tools