Difference between revisions of "Equipment/AxminsterBeltDiscSander"

From Makespace
Jump to: navigation, search
(Created page with "Equipment / Disc and Belt Sander Our combined disc and belt sander = Summary = A sander is a tool designed to sand...")
 
(Add warning about sanding metal)
(One intermediate revision by one user not shown)
Line 1: Line 1:
 +
{{OrangeTool}}
 +
 
[[Equipment|Equipment]] / Disc and Belt Sander
 
[[Equipment|Equipment]] / Disc and Belt Sander
  
Line 19: Line 21:
 
'''Fire'''
 
'''Fire'''
 
* Equipment will be checked for defects before each use to minimise the risk of possible electrical faults or fire.  
 
* Equipment will be checked for defects before each use to minimise the risk of possible electrical faults or fire.  
* Carbon Dioxide extinguisher to be available for any electrical fires  
+
* Carbon Dioxide extinguisher to be available for any electrical fires
 +
* Do not use for sanding metal, as the resulting sparks can cause sawdust to ignite
  
 
'''Electric shock'''  
 
'''Electric shock'''  

Revision as of 16:06, 10 February 2015

Class Orange equipment: Only use if you are confident doing so. Training is available if not.
(More about equipment classes)

Equipment / Disc and Belt Sander
Our combined disc and belt sander

Summary

A sander is a tool designed to sand down or smooth primarily wood for shaping and to prepare it for finishing. It can also be used to smooth or round edges. The sander is rather large and if not used properly can result in damaging to your material or causing serious injury. However, using the sander is a pretty simple operation.

Owners

Health and Safety

Sharp Object/material

  • Power supply to be disconnected when changing belts or discs.
  • Wait for all surfaces to stop moving before adjusting the tool.

Slips, Trips and Falls

  • Waste material/offcuts to be kept clear of work area.

Fire

  • Equipment will be checked for defects before each use to minimise the risk of possible electrical faults or fire.
  • Carbon Dioxide extinguisher to be available for any electrical fires
  • Do not use for sanding metal, as the resulting sparks can cause sawdust to ignite

Electric shock

  • The equipment will be checked before each use to ensure that there are no defects in the casing, battery or cutting head.

Sight/Noise/Dust/Vibration

  • P.P.E. to be worn when using the equipment.
  • Regular brakes to prevent fingers becoming numb

Repetitive Action/Physical Fatigue

  • Regular breaks if work is lasting more than 5 minutes in duration

Training

Instructions

If you've never used a belt/disc sander then it would be worth watching this video for an introduction to a similar machine.

Please refer to the product manual for detailed instructions on how to use the belt sander. A printed copy is also kept with the sander. File:Disc Belt manual.pdf

Prepare your wood to be sanded by ensuring it is properly secured on the table or workbench.

Put on the necessary safety gear, such as goggles or gloves. Belt sanders can kick up a lot of sawdust, which can easily fly into your eyes. This could lead to instinctively dropping the sander, which could cause injury.

Start the motor of the belt sander while holding it away from the wood you intend to sand. Ensure it is at full speed before bringing it in contact with the wood. Start with a coarse belt, and finish up the sanding with a finer grit.

Bring the rear of the sander down to the wood, ensuring you have a firm grip on the back handle, which is used to control the sander.

Bring the rest of the sander onto the wood as smooth as possible.

Move the sander back and forth in smooth, even motions, using the front handle to guide it across the wood.

Tips & Tricks

Always move the belt sander parallel to the grain of the wood. This will ensure an even and smooth surface.

Always keep the sander moving, as leaving it running in one place on the wood can prevent an uneven surface.

Don't tip the sander on its side, as the edge of the sander can cut into the wood

Don't put any unnecessary extra pressure on the wood. The belt sander is a heavy instrument and typically uses its own weight to apply even pressure.

Maintenance

Every month inspect for damage and general wear and tear and asses state of stock blades and replace as needed.

Every six months the carbon motor brushes should be inspected for wear, and replaced as necessary.

Further Information

Introduction video for combined disc and belt sander

File:Disc Belt manual.pdf