Difference between revisions of "Equipment/Electronics Workbenches"
From Makespace
(→Equipment: List current equipment in more detail) |
|||
| Line 3: | Line 3: | ||
Workbenches for electronics and precision work. | Workbenches for electronics and precision work. | ||
| − | [[File:Electronics-thumb.jpg]] | + | [[File:Electronics-thumb.jpg|right]] |
| − | |||
| − | + | == Enthusiast Bench == | |
| + | A 1800mm x 900mm ESD cantilever bench from [http://www.bigdug.co.uk/workshop-benches-c348/antistatic-workbenches-c721/antistatic-workbenches-capacity-300kgs-pp4582 here] | ||
| − | == Equipment == | + | === Equipment === |
| + | * Hameg HM-203s 20MHz analogue oscilloscope | ||
| + | * Black*Star Jupiter 500 0.1Hz-500kHz function generator (sine, square, sawtooth) | ||
| + | * Philips PM6622 80MHz counter | ||
| + | |||
| + | |||
| + | == Expert Bench == | ||
| + | A 1800mm x 900mm ESD cantilever bench from [http://www.bigdug.co.uk/workshop-benches-c348/antistatic-workbenches-c721/antistatic-workbenches-capacity-300kgs-pp4582 here] | ||
| + | |||
| + | === Equipment === | ||
| + | * BlackJack BK6000 Rework station | ||
| + | * Philips PM 3217 50MHz analogue Oscilloscope | ||
| + | * Thurlby Thandar TG212 0.1Hz-2MHz function generator (sine, square, sawtooth) | ||
| + | * Thurlby Thandar TF830 1.3GHz high resolution reciprocal measurement | ||
<gallery> | <gallery> | ||
| Line 15: | Line 28: | ||
</gallery> | </gallery> | ||
| − | == | + | == Shared equipment == |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
* Soldering irons: | * Soldering irons: | ||
** 2x Tenma AT60D soldering stations (up to 400C) | ** 2x Tenma AT60D soldering stations (up to 400C) | ||
| − | |||
| − | |||
| − | |||
| − | |||
* Bench power supplies (e.g. a mix of 5V, 12V, variable, and multi-rail PSUs) | * Bench power supplies (e.g. a mix of 5V, 12V, variable, and multi-rail PSUs) | ||
** Farnell AP20-80: up to 20V at up to 80A | ** Farnell AP20-80: up to 20V at up to 80A | ||
** Hameg HM7042-3 dual: each channel up to 32V at up to 2A | ** Hameg HM7042-3 dual: each channel up to 32V at up to 2A | ||
** Tenma 72-8695 two channels each up to 32V at up to 3A, plus a single fixed 5V/2A channel | ** Tenma 72-8695 two channels each up to 32V at up to 3A, plus a single fixed 5V/2A channel | ||
| + | * Logic analyser: | ||
| + | ** HP 16500A (status unknown: may not be operational but has probes pack) | ||
| + | ** Currently assumed dead. | ||
| − | + | === Components and small tools === | |
| − | + | ||
| − | + | ||
| − | * | + | * PCB holders or "helping hands" |
| − | ** | + | * Magnifying lamps |
| − | ** | + | * Side cutters |
| + | * Multimeters | ||
| + | * Wire | ||
| + | * Selection of basic components (res, caps, v-reg, basic digital logic, basic IC's - 555,358, connectors, cable) | ||
| − | + | == Notes == | |
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
| − | + | ||
It would be nice if someone could dig out URLs for manuals for the above, if available, and link to them from their listing lines. | It would be nice if someone could dig out URLs for manuals for the above, if available, and link to them from their listing lines. | ||
| − | == | + | == Wishlist == |
| − | + | ===Need=== | |
* Abrasive pen | * Abrasive pen | ||
* Heatsink tweezers | * Heatsink tweezers | ||
| − | * | + | * Tweezers |
| − | + | ||
* ESD handling equipment, eg. anti-static mats, wrist-strap, earth points, tester | * ESD handling equipment, eg. anti-static mats, wrist-strap, earth points, tester | ||
| − | |||
| + | ===Want=== | ||
| + | * Logic Analyser | ||
| + | * 100MHZ Digital Oscilloscope | ||
| + | |||
| + | ===Would Be Nice=== | ||
| + | * USB microscope with monitor | ||
| + | * Spectrum Analyser | ||
| + | |||
| + | == Archive== | ||
Bench Requirements (based on conversations with lots of people!) | Bench Requirements (based on conversations with lots of people!) | ||
* Height: Standard workstation/stool height (~840mm) rather than desk/chair height - allows working standing or sitting on stools | * Height: Standard workstation/stool height (~840mm) rather than desk/chair height - allows working standing or sitting on stools | ||
| Line 77: | Line 79: | ||
** Worksurface (e.g. kitchen) fixed to wall with some drawer units as stands (e.g. ikea) | ** Worksurface (e.g. kitchen) fixed to wall with some drawer units as stands (e.g. ikea) | ||
* Other considerations: | * Other considerations: | ||
| − | ** Allow for a variable number of people to sit at it (i.e. | + | ** Allow for a variable number of people to sit at it (i.e. bunch up, couple of people around same project) |
** Decent storage for all the basic tools, components | ** Decent storage for all the basic tools, components | ||
** Some form of raised area for scopes/test equipment | ** Some form of raised area for scopes/test equipment | ||
** Very sturdy - i.e. wont move if lent on, pushed against etc | ** Very sturdy - i.e. wont move if lent on, pushed against etc | ||
Revision as of 22:48, 23 February 2014
Equipment / Electronics Workbenches
Workbenches for electronics and precision work.
Contents
Enthusiast Bench
A 1800mm x 900mm ESD cantilever bench from here
Equipment
- Hameg HM-203s 20MHz analogue oscilloscope
- Black*Star Jupiter 500 0.1Hz-500kHz function generator (sine, square, sawtooth)
- Philips PM6622 80MHz counter
Expert Bench
A 1800mm x 900mm ESD cantilever bench from here
Equipment
- BlackJack BK6000 Rework station
- Philips PM 3217 50MHz analogue Oscilloscope
- Thurlby Thandar TG212 0.1Hz-2MHz function generator (sine, square, sawtooth)
- Thurlby Thandar TF830 1.3GHz high resolution reciprocal measurement
- Soldering irons:
- 2x Tenma AT60D soldering stations (up to 400C)
- Bench power supplies (e.g. a mix of 5V, 12V, variable, and multi-rail PSUs)
- Farnell AP20-80: up to 20V at up to 80A
- Hameg HM7042-3 dual: each channel up to 32V at up to 2A
- Tenma 72-8695 two channels each up to 32V at up to 3A, plus a single fixed 5V/2A channel
- Logic analyser:
- HP 16500A (status unknown: may not be operational but has probes pack)
- Currently assumed dead.
Components and small tools
- PCB holders or "helping hands"
- Magnifying lamps
- Side cutters
- Multimeters
- Wire
- Selection of basic components (res, caps, v-reg, basic digital logic, basic IC's - 555,358, connectors, cable)
Notes
It would be nice if someone could dig out URLs for manuals for the above, if available, and link to them from their listing lines.
Wishlist
Need
- Abrasive pen
- Heatsink tweezers
- Tweezers
- ESD handling equipment, eg. anti-static mats, wrist-strap, earth points, tester
Want
- Logic Analyser
- 100MHZ Digital Oscilloscope
Would Be Nice
- USB microscope with monitor
- Spectrum Analyser
Archive
Bench Requirements (based on conversations with lots of people!)
- Height: Standard workstation/stool height (~840mm) rather than desk/chair height - allows working standing or sitting on stools
- Depth: Standard electronics workstation depth of ~900mm to allow for equipment at the back whilst still giving decent workspace
- ESD - whilst some people don't care, other seem to care a lot, so assume antistatic worksurface
- Structure - A long workbench surface along the wall of the main workshop, approximately 4m; Options:
- Standard electronics workbenches (metal structure bench with drawers below left/right, back power strip at back, raised shelf)
- Basic electronics workbences without storage below, cantilever or 4-post design
- Worksurface (e.g. kitchen) fixed to wall with some drawer units as stands (e.g. ikea)
- Other considerations:
- Allow for a variable number of people to sit at it (i.e. bunch up, couple of people around same project)
- Decent storage for all the basic tools, components
- Some form of raised area for scopes/test equipment
- Very sturdy - i.e. wont move if lent on, pushed against etc
