Difference between revisions of "Equipment/MakitaCharger"

From Makespace
Jump to: navigation, search
(Created page with " = Summary = == Owners == == Health and Safety == '''Sharp Object/material''' * All cutting blades to be kept in their holders until they are required. * Power supply to ...")
 
 
Line 1: Line 1:
 
+
[[File:Charger.JPG|thumb|200px|right|link=Equipment/MakitaCharger|Makita DC18RC Li-Ion Charger]]
  
 
= Summary =
 
= Summary =
  
 
+
After due debate it was decided that whenever possible we would use cordless tools that use the Makita Lithium Ion battery. It means we need just one charger for most of our cordless tools. Please recharge batteries before they get flat.
 +
 
== Owners ==
 
== Owners ==
  
  
 
== Health and Safety ==
 
== Health and Safety ==
'''Sharp Object/material'''
 
* All cutting blades to be kept in their holders until they are required.
 
* Power supply to be disconnected when changing blades.
 
* Be aware of were the blade is in relation to body parts.
 
* Wait for the blade to stop moving before putting the tool down.
 
 
'''Slips, Trips and Falls'''
 
* Waste material/offcuts to be kept clear of work area.
 
  
 
'''Fire'''
 
'''Fire'''
Line 23: Line 16:
 
'''Electric shock'''  
 
'''Electric shock'''  
 
* The equipment will be checked before each use to ensure that there are no defects in the casing, battery or cutting head.  
 
* The equipment will be checked before each use to ensure that there are no defects in the casing, battery or cutting head.  
 
'''Sight/Noise/Dust/Vibration'''
 
* Goggles, ear defenders and dust mask to be worn when using the equipment.
 
* Regular brakes to prevent fingers becoming numb
 
 
'''Repetitive Action/Physical Fatigue'''
 
* Regular breaks if work is lasting more than 5 minutes in duration
 
 
== Training ==
 
 
 
  
 
== Instructions ==
 
== Instructions ==
  
 
== Tips & Tricks ==
 
== Tips & Tricks ==
 
* Keep work area clean and well lit. Cluttered and dark areas invite accidents.
 
* Keep bystanders away while operating a power tool. Distractions can cause you to lose control.
 
* Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
 
* Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a moving part of the power tool may result in personal injury.
 
* Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
 
* Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing, and gloves away from moving parts.
 
* Avoid cutting nails. Inspect work piece for any nails and remove them before operation.
 
  
 
* Tips for maintaining maximum battery life
 
* Tips for maintaining maximum battery life
Line 52: Line 26:
 
** Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.
 
** Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.
 
** Let a hot battery cartridge cool down before charging it.
 
** Let a hot battery cartridge cool down before charging it.
 
== Maintenance ==
 
Every month inspect for damage and general wear and tear and asses state of stock blades and replace as needed.
 
 
Every six months the carbon motor brushes should be inspected for wear, and replaced as necessary.
 
  
 
== Further Information ==
 
== Further Information ==

Latest revision as of 18:04, 30 November 2013

Makita DC18RC Li-Ion Charger

Summary

After due debate it was decided that whenever possible we would use cordless tools that use the Makita Lithium Ion battery. It means we need just one charger for most of our cordless tools. Please recharge batteries before they get flat.

Owners

Health and Safety

Fire

  • Equipment will be checked for defects before each use to minimise the risk of possible electrical faults or fire.
  • Carbon Dioxide extinguisher to be available for any electrical fires

Electric shock

  • The equipment will be checked before each use to ensure that there are no defects in the casing, battery or cutting head.

Instructions

Tips & Tricks

  • Tips for maintaining maximum battery life
    • Charge the battery cartridge before completely discharging.
    • Always stop tool operation and charge the battery cartridge when you notice less tool power.
    • Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.
    • Let a hot battery cartridge cool down before charging it.

Further Information