Difference between revisions of "ScreenprintingOnPaper"

From Makespace
Jump to: navigation, search
(Preparation)
(Detailed instructions)
Line 32: Line 32:
 
# '''Check paper or items are suitable for printing''' For best results paper should not be too thin or it may wrinkle or get waterlogged.  Note that typical 'office' or 'computer' paper (80 gsm) is usually too thin and will not dry flat especially if there is a lot of ink in the design.  Non-paper items should ideally be somewhat absorbent or the print may scratch off.
 
# '''Check paper or items are suitable for printing''' For best results paper should not be too thin or it may wrinkle or get waterlogged.  Note that typical 'office' or 'computer' paper (80 gsm) is usually too thin and will not dry flat especially if there is a lot of ink in the design.  Non-paper items should ideally be somewhat absorbent or the print may scratch off.
 
# '''Prepare a screen and stencil''' – see [[CreatingScreenprintingStencils]]
 
# '''Prepare a screen and stencil''' – see [[CreatingScreenprintingStencils]]
 +
# '''Clamp the screen into the printing frame using the hinge clamps'''
 +
# '''Ensure the screen has suitable snap / off-contact for the thickness of this paper/item'''  To test this press down gently on the centre of the screen. It should depress around 3mm and spring back. Use acrylic pieces (in the small drawer unit) under the edge of screen nearest you to increase the height. If printing on a thick item or using the small platen, also insert acrylic pieces between the underside of the screen inside the clamps.
 
# '''Mix '''non-textile''' printing ink'''
 
# '''Mix '''non-textile''' printing ink'''
 
## First decide on the colour to be printed in this session.   
 
## First decide on the colour to be printed in this session.   

Revision as of 00:14, 14 January 2016

Screenprinting on Paper and non-Fabrics

Summary

Preparation

  1. Check that paper or item is suitable for printing (flat, absorbent)
  2. Prepare a screen and stencil
  3. Clamp the screen into the printing frame using the hinge clamps
  4. Ensure the screen has suitable snap / off-contact for the thickness of this paper/item. To test this press down gently on the centre of the screen. It should depress around 3mm and spring back. Use acrylic pieces (in the small drawer unit) under the edge of screen nearest you to increase the height. If printing on a thick item or using the small platen, also insert acrylic pieces between the underside of the screen inside the clamps.
  5. Mix non-textile printing ink

Printing session

  1. Prepare some pieces of test paper (of similar size to your design)
  2. Select square-profile squeegee
  3. Clear space in drying rack
  4. Print on paper or items

Cleanup

  1. Wash screen, equipment and hands using washing-up liquid and cold water
  2. Mop up any water from the floor to avoid a slip hazard
  3. Log activity and pay for any Makespace materials by items x print size

Detailed instructions

  1. Check paper or items are suitable for printing For best results paper should not be too thin or it may wrinkle or get waterlogged. Note that typical 'office' or 'computer' paper (80 gsm) is usually too thin and will not dry flat especially if there is a lot of ink in the design. Non-paper items should ideally be somewhat absorbent or the print may scratch off.
  2. Prepare a screen and stencil – see CreatingScreenprintingStencils
  3. Clamp the screen into the printing frame using the hinge clamps
  4. Ensure the screen has suitable snap / off-contact for the thickness of this paper/item To test this press down gently on the centre of the screen. It should depress around 3mm and spring back. Use acrylic pieces (in the small drawer unit) under the edge of screen nearest you to increase the height. If printing on a thick item or using the small platen, also insert acrylic pieces between the underside of the screen inside the clamps.
  5. Mix non-textile printing ink
    1. First decide on the colour to be printed in this session.

Note: Items must be dry before printing additional colours so only prepare ink for each colour just before it is needed for printing.

To mix a new batch of non-textile ink:

  1. Take an empty clear plastic ink pot to mix your ink mixture in

and use a spoon to measure out pigments and mix if needed

  1. Choose a colour of System 3 pigment (paint) or mix System 3 pigments to create a new colour. For mixed colours mix well until the colour is completely even, so that the print will be consistent on each item
  2. When the pigment mixture is the colour you want, mix this with an equal amount (1:1) of System 3 Textile print medium.
  3. Mix well until the mixture looks consistent.
  4. For printing the mixture should have a consistency similar to domestic emulsion paint or liquid honey and should drop slowly from a palette knife dipped into it. If it is too dry or sticky to drop, mix in small amounts of extra medium until is more fluid. This can happen when ink has been stored and reused.