Difference between revisions of "Equipment/AxminsterScrollSaw"
Perfectphase (Talk | contribs) (Created page with "Equipment / Scroll Saw Rage 3DB Mitre Saw = Summary = A scroll saw is a small electric or pedal-operated saw that is usef...") |
Perfectphase (Talk | contribs) m (→Training) |
||
| Line 36: | Line 36: | ||
== Training == | == Training == | ||
| + | No mandatory training is required to use this tool. | ||
| + | |||
| + | Optional training will be available in the near future. | ||
== Instructions == | == Instructions == | ||
Revision as of 01:59, 8 April 2013
Equipment / Scroll Saw
Contents
Summary
A scroll saw is a small electric or pedal-operated saw that is useful for cutting intricate curves in cases where a jigsaw or coping saw is not appropriate. It is capable of creating curves with edges. It is somewhat similar to a band saw, but unlike band saws, in which the saw blade is a continuous loop, scroll saws use saw blades similar to those of coping saws and operate through a quick reciprocating up and down motion.
A scroll saw has two main advantages when compared to a band saw. The first is that the blade can be removed and placed in situ through a pre-drilled starting hole. This feature allows interior cut-outs to be made without creating an entry slot for the blade through the edge of the workpiece. Second, a scroll saw can cut significantly more intricate curves.
Owners
Health and Safety
Sharp Object/material
- Power supply to be disconnected when changing Blades.
- Wait for the blade to stop moving before removing the material or attempting any adjustments.
Slips, Trips and Falls
- Waste material/offcuts to be kept clear of work area.
Fire
- Equipment will be checked for defects before each use to minimise the risk of possible electrical faults or fire.
- Carbon Dioxide extinguisher to be available for any electrical fires
Electric shock
- The equipment will be checked before each use to ensure that there are no defects in the casing, battery or cutting head.
Sight/Noise/Dust/Vibration
- P.P.E. to be worn when using the equipment.
- Regular brakes to be taken to prevent fingers becoming numb
Repetitive Action/Physical Fatigue
- Regular breaks to be taken if work is lasting more than 5 minutes in duration
Training
No mandatory training is required to use this tool.
Optional training will be available in the near future.
Instructions
Please watch these introduction videos Miter Saw Safety and Miter Saw Safety & Operation before using the saw.
For detailed instructions se the manual or the saw Rage 3DB Manual
Technical Specification
| Cuts per Minute | 400-1,400 |
| Max Depth of Cut | 65mm |
| Net Weight | 29kg |
| Overall L x W x H | 620 x 285 x 310mm |
| Power | 120W |
| Rating | Trade |
| Stroke | 10 & 20mm |
| Table Size | 460 x 235mm |
| Table Tilt | 0-45° |
| Throat | 460mm(18") |
Tips & Tricks
- Always test run the cut without power to ensure there are no problems and your hands are clear of the blade.
- Be aware of the location of any power cords when operating the saw, keeping them out of the path of the cut at all times.
- Be aware of where cut off pieces of lumber will fall, to avoid injuries; if possible clamp or support the offcuts.
- Be especially careful of the placement of your hands when cutting at an angle. if possible clamp the workpiece so you hands are well clear of the machine when cutting.
- A circular saw blade will almost always kick straight back. Watch your body position. Keep slightly to the side, and never keep a hand behind the blade.
Maintenance
Every month inspect for damage and general wear and tear and asses state of stock blades and replace as needed.
Every six months the carbon motor brushes should be inspected for wear, and replaced as necessary.
Replacement blades Rage 255mm TCT Blade £30
