Revision as of 09:10, 20 August 2013

Big box!

Big Box of Breakout Boards and Bits

We have a box of bits containing Arduinos for use in the space along with an assortment of sensors, motors, lights and other things you might need to make up a project. It lives in... (to be confirmed, currently it lives in my kitchen, obviously that won't be its final location!)

This page exists to catalogue the contents of the box along with any notes on how to use each modules, including links to Arduino libraries, datasheets, photos showing pinouts and suchlike. Basically if you've figured out how to use a module through extensive googling and experimentation here is where you can share that knowledge with everyone else. Use your signatures to claim credit!

Policies

This is not primarily intended to be used as stock for people's projects, rather it's there to provide a lending library of parts for use at events such as the Arduino and Cake sessions and Family Makers. That said, none of the parts are particularly expensive and we try to have a reasonable number of them so if you really need something for a project right now, aren't going to be taking the last one of something and are prepared to provide a replacement in non ludicrous time that's probably fine. If unsure ask on the mailing list! Most things here have been bought from sellers from the far East on eBay, so while they're cheap the lead times are often quite lengthy.

There's a section at the end of this page for requests - if there's something you'd like to have access to and which is of general use (i.e. not for just one project you have in mind) add some details and we'll see whether we can source it at an appropriate price. If something goes wrong and the magic white smoke escapes from something please make a note in the section for the component or module concerned, that way we know it's broken and can either fix or replace it (and tell everyone how to avoid the same thing happening again)

What's in the Box?

Contents of the box, both current and planned. Things that have arrived and are ready for use are marked in this colour. We need photos and documentation for everything on this list!

Spotter's Guide
Max7219 based dot matrix display	Max7219 based seven segment LED display	5v stepper motor	Driver board for 5v stepper motor
NRF24L01 radio modules	IR beam break detector	DHT11 temperature / humidity sensor	Barometric pressure sensor
Geared 6v motor (ex servo)	Assorted pink, green, orange and blue LEDs	MPU6050 six axis motion sensor	Arduino nano v3
Arduino nano ethernet shield	Blue LCD display	9g servo and accessories	Ultrasonic rangefinder board
Dual H-bridge module	Cables of lurve

Arduinos

6x Arduino Nano v3

Breadboard compatible Arduinos with ATMega328 processors. Note that the 3.3v rail is driven from the FTDI chip (the part that interfaces with USB) so is only available when powered through the USB cable (in other cases use a 3.3v regulator). If supplying external power remember to use the VIn pin and not the 5v one, even if you think you have a regulated power supply.

Sensors and Input Devices

3x DHT11 temperature and humidity Sensors

These modules break out the three usable pins on the DHT11 sensors

MPU6050 based 6 axis motion sensor board

I2C based motion processor, contains a 3 axis gyroscope in conjunction with a 3 axis linear accelerometer and an embedded DSP

1x Barometric pressure sensor board

Not tested yet, but believed to be a BMP085, which if so is capable of resolving pressure differences corresponding to about 20cm of altitude, very nifty!

Ultrasonic rangefinders

Modules with an ultrasonic emitter / receiver pair and the logic to calculate distance to a reflecting object based on timing.

Motors and other Output Devices

12x Dual H-bridge modules, used to drive regular and stepper motors

H-Bridge modules, used to interface to high power devices including motors and drive them from the logic level signals on the Arduino.

1x hacked HiTec HS-625MG

A tough servo with the servo bits removed, now just acts as a high quality electric motor with a gearbox. Drive at 5-6v and use conventional PWM / H-Bridge to alter its speed and direction.

10x 9g servo motors

Basic servo motors. Use the Servo or modified Servo2 library (the latter for when you need to drive more than a couple of servos at a time from the Arduino)

4x 5V stepper motors with driver boards

Document how to make them work here (Martin?) - there's more info on these exact boards along with example code here, yet to be tried but they look identical!

Communications

10x NRF24L01 Radio Modules

Short range radio modules, use the mIRF library.

2x Arduino nano ethernet shields

Stackable modules providing an ethernet jack

LEDs and displays

High brightness LEDs

20 each of four different colours (pink, green, blue and orange) 5mm LEDs, remember to use current limiting resistors or a constant current source when driving them!

4x LED Dot matrix modules with drivers

Dot matrix displays, single colour with drivers

2x Eight digit seven segment displays with drivers

Standard 'calculator style' seven segment displays in a module of eight of them with associated driver circuitry.

4x LCD 20x4 character displays

LCD character displays, serial protocol (probably!) to drive them.

Everything else

2x IR correlation modules

IR beam break sensors with amplifiers to provide a clean signal. Not tested yet!

10x Playstation style joysticks

Analogue joysticks with an embedded press button

Male to male and male to female jumper leads

A load of long jump leads with pins and sockets (depending on type) to make it easier to interface to modules such as the NRF24L which have otherwise awkward pin layouts and can't be directly connected to a breadboard.

Requests

Put your requests for parts here...